Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
ion sourceShinto, Katsuhiro; Shibata, Takanori*; Okoshi, Kiyonori; Nammo, Kesao*; Kawai, Isao*; Ikegami, Kiyoshi*
Journal of Physics; Conference Series, 2743, p.012023_1 - 012023_5, 2024/05
We have been conducting the test of a new J-PARC-made internal antenna for the J-PARC RF-driven cesiated H ion source. After the development of the first J-PARC-made antenna, the composition of the porcelain enamel coating of the antenna was changed because we were afraid of the outgassing of the impurities from the previous antenna coating. During the test of high-density plasma production by the new antenna, we monitored the outgassing characteristics of the new antenna by measuring mass spectrometry and optical spectrum analysis. It is confirmed that no remarkable impurities were emitted from the new antenna. We also carried out the H beam extraction and measured the H beam characteristics by using the new antenna. It is found that the emittances of the H beam extracted from the J-PARC RF-driven cesiated H ion source by using the new antenna were similar to those in the case by using the SNS-made antenna. To accelerate the endurance test of the new antenna, we applied the antenna for the high-density plasma production to the 5% duty factor (1 ms pulse width with 50 Hz repetition rate) with the 2 MHz RF input power of approximately 60 kW, whose values were much higher than those in the J-PARC nominal operation; 0.8 ms pulse width with 25 Hz repetition rate (the duty factor of 2%) with the RF input power of approximately 30 kW. This presentation shows the results of the characteristics of the new J-PARC-made antenna and discusses the feasibility of the new antenna for use in the J-PARC accelerator operation.
Shibata, Takanori*; Shinto, Katsuhiro; Nakano, Haruhisa*; Hoshino, Kazuo*; Miyamoto, Kenji*; Okoshi, Kiyonori; Nammo, Kesao*; Ikegami, Kiyoshi*; Kawai, Isao*; Oguri, Hidetomo; et al.
Journal of Physics; Conference Series, 2743, p.012007_1 - 012007_5, 2024/05
Oscillation of the negative hydrogen ion (H) beam phase space in Radio Frequency (RF) ion source is investigated by a simple 3D Particle-In-Cell (PIC) model which takes into account the transport processes of electron, proton and H in the extraction region. The calculation domain is in vicinity of the single beam aperture in J-PARC ion source configuration. In order to understand relation between the plasma density oscillation and the extracted H beam characteristics, the input electron and proton fluxes from the driver region are varied parametrically with the 1st and the 2nd harmonics of the J-PARC RF frequency (2 or 4 MHz). The numerical results give an idea to the main physical processes between the oscillations of the plasma parameters and the extracted H ion trajectories in the different RF phases. Countermeasures to reduce the oscillation mechanisms are also discussed in the presentation.
ion beam extracted from an RF wave excited ion source plasmaWada, Motoi*; Shibata, Takanori*; Shinto, Katsuhiro
Journal of Physics; Conference Series, 2743, p.012031_1 - 012031_5, 2024/05
An internal antenna type RF driven negative hydrogen (H) ion source supplies beams to the J-PARC accelerator facility. The H ion beam current exhibits high stability, while it fluctuates with less than 5% amplitude of the DC current when a Faraday cup measures the current extracted from the source mounted on a test stand. Two frequencies are identified as the main oscillation components, 2 MHz and 4 MHz which are the driving RF frequency and the second harmonics, respectively. The amplitude levels of these components appear larger as parts of the beam directing specific angles passing through a slit are detected. A possible reason for observing a small amplitude oscillation in the total beam intensity is the averaged phase-shift of the local beam depending upon the position of the H ion production and the succeeding trajectory reaching the Faraday cup. To confirm if the phase-shift is the main reason for diminishing the oscillation amplitude for the total beam, the phase-shift between the 2 MHz and 4 MHz components were measured for beams passing through a 0.1 mm slit coupled to a Faraday cup having a 0.1 mm entrance slit. The result indicated the phase-shift changed substantially depending upon the position, but no simple model can explain the measured spatial distribution of the phase-shift. Further attempts will be made to clarify the beam dynamics relevant to the H ion beam transport including the measurements of the beam current phase-shift with respect to the RF antenna current, and the time evolution of Balmer-
light emission.
Shibata, Takanori*; Shinto, Katsuhiro; Nammo, Kesao*; Okoshi, Kiyonori; Ikegami, Kiyoshi*; Oguri, Hidetomo; Ishida, Masaki*; Wada, Motoi*
Journal of Instrumentation (Internet), 19, p.C01009_1 - C01009_8, 2024/01
From Nov. 2020 to Apr. 2021, the continuous ion source operation for 3,651 hours (5 months) was achieved. As the lifetime of the RF ion source is mainly limited by failure on the enamel coating of the RF antenna, detailed evaluation of the antenna surface is required to ensure feasibility of the further extension of the operation time. In the present study, surface discoloration on the RF antenna coil observed after the 5 months operation is investigated by application of digital microscope and SEM/EDS analyses. The material mapping and the line spectrum obtained by the EDS analysis show that depositions of the sputtered source chamber wall materials and the injected cesium on to the enamel coating are the most possible candidate for the discoloration. The dimension measurements of the RF antenna thickness before and after the long-term operation support the idea that the discoloration is due to the deposited materials and hence insulation of the RF antenna coil by enamel coating is maintained. The emittance measurement after the operation also shows that the RF plasma and the beam formations are not affected by the deposition on the antenna.
Shinto, Katsuhiro; Okoshi, Kiyonori; Shibata, Takanori*; Nammo, Kesao*; Kawai, Isao*; Ikegami, Kiyoshi*; Ueno, Akira
Proceedings of 20th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.928 - 931, 2023/11
J-PARC initiated the operation of the high-intensity rf-driven negative hydrogen (H) ion source in 2014 autumn. The ion source produces the H beam with the beam current of 60 mA and the beam energy of 50 keV in order to inject the H beam into the 3 GeV RCS with the beam current of 50 mA and the beam energy of 400 MeV from the J-PARC linac. We have achieved the longest continuous operation time of 4001 hours in the previous (2021/2022) campaign. The 2022/2023 campaign was the first time that the continuous operation of the H ion source without any exchanges of the ion source until the end of the campaign was examined. We present the operation status of the J-PARC H ion source in this campaign as well as the status of the J-PARC-made internal antenna test.
Shinto, Katsuhiro; Shibata, Takanori*; Wada, Motoi*
Proceedings of 20th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.392 - 395, 2023/11
Negative hydrogen (H) ion sources which are used at high-intensity proton accelerator facilities such as J-PARC or neutral beam injection system for plasma heating in the fusion devices such as ITER produce plasmas by using RF sources driving with the frequency of 1-2 MHz. We have shown that the H beams extracted from the RF-driven H ion source with the frequency of several MHz have some fluctuations with the frequency of the fundamental and second harmonics. The reason is that the high plasma density is produced in the ion source with the low driving frequency. Therefore, we propose the driving RF frequency same as the RF sources with that of 324 MHz in the J-PARC linac, which is much higher than the ion plasma frequency, is used for producing the plasma to suppress the H beam fluctuations. As a first step, we performed a design of a matching circuit for the higher frequency driven H ion source. We present the background for decision of a new RF amplifier with much higher frequency and the design results.
ion sourceShinto, Katsuhiro; Shibata, Takanori*; Okoshi, Kiyonori; Nammo, Kesao*; Ikegami, Kiyoshi*; Oguri, Hidetomo
Proceedings of 19th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.675 - 679, 2023/01
In J-PARC, we have been conducting the test of a J-PARC-made internal antenna in order to establish the production method and understand the beam characteristics of the antenna. At this time, we investigated the outgas characteristics during the production of a high-density plasma by using the J-PARC-made antenna. It is confirmed that no remarkable impurities are emitted from the antenna by a residual gas analysis using a quadrupole mass analyzer installed downstream the ion source and a spectroscopic analysis of the plasma in the ion source. It is found that the emittances of the H beam extracted from the J-PARC radio-frequency H ion source by using the antenna was similar as those in case by using SNS antenna.
Shibata, Takanori*; Ishida, Masaki*; Nammo, Kesao*; Ikegami, Kiyoshi*; Okoshi, Kiyonori; Shinto, Katsuhiro; Oguri, Hidetomo
Proceedings of 19th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.863 - 867, 2023/01
Continuous operation duration of the J-PARC Radio Frequency (RF) ion source has been extended step by step these years for the goal to supply stable beam during the entire period of J-PARC user operation (around 7 months) each year. A 3651 hours (5 months) continuous ion source operation has been achieved from Nov. 2020 to Apr. 2021. As the lifetime of the ion source is mainly limited by failure on the RF antenna coil, detailed evaluation of the antenna surface condition is required to ensure the feasibility of the further extension of the operation time. In the present study, dimension measurements and SEM/EDS analyses were applied to understand the surface discoloration of the RF antenna. The discoloration after the long-term continuous operation is due to deposition of injected cesium (for H surface production process) and of stainless used steel (Fe, Cr, Ni) from the ion source components sputtered by plasma. The results show that the enamel coating of the RF antenna has not worn out in the long-term continuous operation for several months and, hence, extension of the ion source continuous operation duration can be extended.
ion source with new parts exposed to plasmaUeno, Akira; Okoshi, Kiyonori; Ikegami, Kiyoshi*; Oguri, Hidetomo
Journal of Physics; Conference Series, 2244, p.012029_1 - 012029_5, 2022/04
Times Cited Count：0 Percentile：0.32(Engineering, Electrical & Electronic)The J-PARC cesiated RF-driven H ion source is stably suppling about 58 mA beam with a duty factor of 1.25 % (0.5 ms
25 Hz) for the J-PARC LINAC 50 mA operations. For them, only three plasma chambers (PCHs) of #7, #8 and #9PCHs among ten PCHs have been used since the transverse emittances are more superior than others for unknown reasons. However, the emittances were enlarged by 16 % with the #7PCH, in which the plasma electrode (PE) temperature control plate (PETCP) was replaced to brand-new one to solve the air leak at the VCR vacuum fitting. The impurities from the new parts exposed to the plasma seemed to cause the degradation. The beam with almost the best emittances was reproduced by #4PCH with a new PETCP, in which sapphire tubes were used instead of the 99.7 % alumina ceramics tubes, after a new 2-MHz RF power scanning impurities reduction conditioning for 48 hours.
Welton, R.*; Bollinger, D.*; Dehnel, M.*; Draganic, I.*; Faircloth, D.*; Han, B.*; Lettry, J.*; Stockli, M.*; Tarvainen, O.*; Ueno, Akira
Journal of Physics; Conference Series, 2244, p.012045_1 - 012045_13, 2022/04
Times Cited Count：2 Percentile：86.84(Engineering, Electrical & Electronic)High brightness, negative hydrogen ion sources are used extensively in many scientific facilities operating worldwide. Negative hydrogen beams have become the preferred means of filling circular accelerators and storage rings. Several facilities now have long-term (
several years) experience with operating a variety of these sources (RF, filament, magnetron and penning) and have encountered, and in some cases solved, performance limiting issues. A representative list of such facilities includes, the US Spallation Neutron Source (SNS), Japan Proton Accelerator Complex (J-PARC), Rutherford Appleton Laboratory (RAL-ISIS), Los Alamos Neutron Science Center (LANSCE), Fermi National Accelerator Laboratory (FNAL), CERN LINAC-4 and numerous installations of D-Pace ion sources. This report summarizes key ion source sustainability issues encountered at these facilities and discusses how some of them are being addressed through recent source improvements.
Shibata, Takanori*; Okoshi, Kiyonori; Shinto, Katsuhiro; Nammo, Kesao*; Ikegami, Kiyoshi*; Oguri, Hidetomo
Journal of Physics; Conference Series, 2244, p.012041_1 - 012041_5, 2022/04
Times Cited Count：1 Percentile：69.82(Engineering, Electrical & Electronic)In the J-PARC user operation from Nov. 2020 - Apr. 2021, continuous operation of J-PARC Radio Frequency (RF) negative hydrogen ion (H) source up to 3,651 hours (5 months) has been achieved. The ion source was operated with the output H current of 60 mA, the duty factor (for plasma generation) 2% and the input RF power up to 30 kW. After the operation, phase space diagrams at the Radio Frequency Quadrupole (RFQ) entrance were measured by the emittance monitor at the ion source test stand (IS-TS) under the same operation condition as in the J-PARC Linac. Comparison of the phase spaces and the beam emittances between the ion sources in the present and the previous operations shows slight difference. From the direct observation of the antenna coil, no exhaustion or the decrease in the thickness of the enamel coating of the coil have been confirmed. The results indicate the possibility of the next goal of the long-run up to 7 months, which is the same as the full duration of the J-PARC user operation in 1 year.
beam extracted from an RF-driven high-intensity H ion sourceShinto, Katsuhiro; Shibata, Takanori*; Wada, Motoi*
Proceedings of 18th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.230 - 233, 2021/10
In most proton accelerator facilities such as J-PARC, SNS, CERN, a H ion source equipped with a 2-MHz rf driver for plasma generation produces H beams. We have reported H beam characteristics extracted from the J-PARC rf-driven high-intensity H ion source. We have been developing an emittance measurement apparatus equipped with a highly time-resolved data acquisition system in order to observe fluctuation of the beam emittance in association with the frequency of the rf driver. By using this apparatus, we found that the beam emittance is fluctuated with the frequency with the rf driver and higher harmonics. We will show some obtained results of the emittance fluctuation.
Shibata, Takanori*; Hirano, Koichiro; Hirane, Tatsuya*; Shinto, Katsuhiro; Hayashi, Naoki; Oguri, Hidetomo
Proceedings of 18th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.417 - 421, 2021/10
In J-PARC linac, the operation of an rf-driven high-intensity H ion source was initiated in 2014. For plasma ignition, the 2-MHz rf amplifier outputs the power of several tens kW. However the rf amplifier for the ion source and those for the accelerating cavities have not been synchronized. As a result, the wave hights in the beam waveforms were different in shot by shot. Therefore, we have developed an synchronization system between the rf system for the ion source and those for the cavity systems and succeeded the same wave hights in the waveforms.
Shibata, Takanori*; Shinto, Katsuhiro; Wada, Motoi*; Oguri, Hidetomo; Ikegami, Kiyoshi*; Okoshi, Kiyonori; Nammo, Kesao*
AIP Conference Proceedings 2373, p.050002_1 - 050002_9, 2021/08
Oscillation of emittance and Twiss parameters in the negative ion beam from the J-PARC 2-MHz RF ion source is measured by applications of a double-slit emittance monitor located at the RFQ (Radio Frequency Quadrupole) entrance. The emittance monitor is equipped with a newly-developed 60 MS/s data acquisition system, so that beam current oscillation in a few MHz can be observed with enough time resolution. From the measurement, it is shown that the beam phase space consists of (1) a DC component in the beam core, (2) a 2-MHz oscillating component which takes place both in the beam core and the halo and (3) a doubled RF frequency (4 MHz) oscillation which slightly exists in the beam halo. The major component is the 2-MHz component, which resultantly decides the beam emittance oscillation frequency. A typical value of the beam emittance in the present experiment is 0.34 
mm-mrad, while the amplitude of the 2 MHz oscillation is around 0.04 mm-mrad. The results indicate that the high-frequency oscillation component occupying about ten-percent of the beam from the RF source travels a few meters passing through a magnetic lens focusing system.
Sarmento, T.*; W
nderlich, D.*; Fantz, U.*; Friedl, R.*; Rauner, D.*; Tsumori, Katsuyoshi*; Shenjin, L.*; Chen, W.*; Bollinger, D.*; Oguri, Hidetomo; et al.
AIP Conference Proceedings 2373, p.110001_1 - 110001_18, 2021/08
In preparation for NIBS 2020 various labs prepared reference sheets containing key information about their ion sources and the machines that they serve. The contents of the reference sheets have been formatted and edited into this paper for posterity and ease of access.
ion source and space-charge neutralized LEBT for 100-mA high energy and high duty factor LINACsUeno, Akira
Review of Scientific Instruments, 91(3), p.033312_1 - 033312_9, 2020/03
Times Cited Count：4 Percentile：27.22(Instruments & Instrumentation)In July 2019, a 3 GeV 920 kW beam was accelerated for 10.5 hours in the J-PARC. During the operation, the H ion source and LINAC was operated with the beam duty factor (BDF) of 1.25% (0.5 ms25 Hz) and the ejected beam intensities of 58 and 50 mA, respectively. Separately, they were stably operated with the BDF of 1.5% (0.6 ms25 Hz) and the ejected beam intensities of 72 and 60 mA, respectively. Based upon the 100-mA and BDF 5% (1 ms50 Hz) H ion source operation on a test-stand, the possibility of the 100-mA high energy and high duty factor LINACs with a radio frequency quadrupole LINAC with an injection energy higher than 64 keV is presented. The unexpectedly effective space-charge neutralization effects in the low energy beam transport are also presented. Furthermore, the transverse emittance improvements by about 8% with the shortest beam extractor are presented.
Oguri, Hidetomo
Purazuma, Kaku Yugo Gakkai-Shi, 95(7), p.340 - 344, 2019/07
no abstracts in English
Shinto, Katsuhiro; Okoshi, Kiyonori; Shibata, Takanori*; Nammo, Kesao*; Ikegami, Kiyoshi*; Takagi, Akira*; Namekawa, Yuya*; Ueno, Akira; Oguri, Hidetomo
AIP Conference Proceedings 2052, p.050002_1 - 050002_7, 2018/12
Times Cited Count：6 Percentile：93.67(Physics, Applied)In the 2017/2018 campaign, the J-PARC cesiated rf-driven negative hydrogen (H) ion source producing H beam with the beam current of 47 mA accomplished three long-term operations more than 2,000 hours without any serious issues. On the final day of this campaign, the ion source produced an H beam current of 72 mA so that the linac commissioning group could demonstrate the beam current of 60 mA at the linac exit. We are also conducting an endurance test of a J-PARC-made antenna at a test bench. The antenna achieved the operation time approximately 1,400 hours.
ion sourceShinto, Katsuhiro; Okoshi, Kiyonori; Ikegami, Kiyoshi*; Takagi, Akira*; Shibata, Takanori*; Nammo, Kesao*; Namekawa, Yuya*; Ueno, Akira; Oguri, Hidetomo
AIP Conference Proceedings 2011, p.050018_1 - 050018_3, 2018/09
Times Cited Count：3 Percentile：81.69(Physics, Applied) ion sourceShinto, Katsuhiro; Shibata, Takanori*; Miura, Akihiko; Miyao, Tomoaki*; Wada, Motoi*
AIP Conference Proceedings 2011, p.080016_1 - 080016_3, 2018/09
Times Cited Count：6 Percentile：93.67(Physics, Applied)