The Development of a Multiphysics Coupled Solver for Studying the Effect of Dynamic Heterogeneous Configuration on Particulate Debris Bed Criticality and Cooling Characteristics

Li, C.-Y.; Wang, K.*; Uchibori, Akihiro; Okano, Yasushi; Pellegrini, M.*; Erkan, N.*; Takata, Takashi*; Okamoto, Koji*

Applied Sciences (Internet), 13(13), p.7705_1 - 7705_29, 2023/07

https://doi.org/10.3390/app13137705

Evaluation of fuel reactivity worth measurement in the prototype fast reactor Monju

Ohgama, Kazuya; Takegoshi, Atsushi*; Katagiri, Hiroki; Hazama, Taira

Nuclear Technology, 208(10), p.1619 - 1633, 2022/10

https://doi.org/10.1080/00295450.2022.2045532

Development of the unified cross-section set ADJ2017R

Yokoyama, Kenji; Maruyama, Shuhei; Taninaka, Hiroshi; Oki, Shigeo

JAEA-Data/Code 2021-019, 115 Pages, 2022/03

JAEA-Data-Code-2021-019.pdf:6.21MB
JAEA-Data-Code-2021-019-appendix(CD-ROM).zip:435.94MB

In JAEA, several versions of unified cross-section set for fast reactors have been developed so far; we have developed a new unified cross-section set ADJ2017R, which is an improved version of the unified cross-section setADJ2017 for fast reactors. The unified cross-section set is used for reflecting information of C/E values (analysis / experiment values) obtained by integral experiment analyses in reactor core design via the cross-section adjustment methodology; the values are stored in the standard database for FBR core design. In the methodology, the cross-section set is adjusted by integrating the information such as uncertainty (covariance) of nuclear data, uncertainty of integral experiment / analysis, sensitivity of integral experiment with respect to nuclear data. ADJ2017R basically has the same performance as ADJ2017, but we conducted an additional investigation on ADJ2017 and revised the following two points. The first is to unify the evaluation method of the correlation coefficient of uncertainty caused by experiments (hereinafter referred to as the experimental correlation coefficient). Because it was found that the common uncertainty used in the evaluation of the experimental correlation coefficient was evaluated by two different methods, the experimental correlation coefficients were revised for all experimental data, and the evaluation method was unified. The second is the review of the integral experiment data used for the cross-section adjustment calculation. It was found that one of the experimental values of composition ratio after irradiation of the Am-243 sample has a problem in uncertainty evaluation because its experimental uncertainty is extremely small compared to the others. The cross-section adjustment calculation was, therefore, redone by excluding the experimental value. In the creation of ADJ2017, a total of 719 data sets were analyzed and evaluated, and eventually adopted 620 integral experimental data sets. In contrast, a total of 61

Re-examinations of MA fuel composition for accelerator-driven system and its heat removal

Sugawara, Takanori; Moriguchi, Daisuke*; Ban, Yasutoshi; Tsubata, Yasuhiro; Takano, Masahide; Nishihara, Kenji

JAEA-Research 2021-008, 63 Pages, 2021/10

JAEA-Research-2021-008.pdf:4.43MB

This study aims to perform the neutronics calculations for accelerator-driven system (ADS) with a new fuel composition based on the SELECT process developed by Japan Atomic Energy Agency because the previous studies had used the ideal MA (minor actinide) fuel composition without uranium and rare earth elements. Through the neutronics calculations, it is shown that two calculation cases, with/without neptunium, satisfy the design criteria. Although the new fuel composition includes uranium and rare earth elements, the ADS core with the new fuel composition is feasible and consistent with the partitioning and transmutation (P&T) cycle. Based on the new fuel composition, the heat removal during fuel powder storage and fuel assembly assembling is evaluated. For the fuel powder storage, it is found that a cylindrical tube container with a length of 500 [mm] and a diameter of 11 - 21 [mm] should be stored under water. For the fuel assembly assembling, CFD analysis indicates that the cladding tube temperature would satisfy the criterion if the inlet velocity of air is larger than 0.5 [m/s]. Through these studies, the new fuel composition which is consistent with the P&T cycle is obtained and the heat removal with the latest conditions is investigated. It is also shown that the new fuel composition can be practically handled with respect to heat generation, which is one of the most difficult points in handling MA fuel.

A Validation study of a neutronics design methodology for fast reactors using reaction rate distribution measurements in the prototype fast reactor Monju

Ohgama, Kazuya; Takegoshi, Atsushi; Katagiri, Hiroki*; Hazama, Taira

Proceedings of 2019 International Congress on Advances in Nuclear Power Plants (ICAPP 2019) (Internet), 8 Pages, 2019/05

Impact of impurity in transmutation cycle on neutronics design of revised accelerator-driven system

Sugawara, Takanori; Katano, Ryota; Tsujimoto, Kazufumi

Annals of Nuclear Energy, 111, p.449 - 459, 2018/01

https://doi.org/10.1016/j.anucene.2017.09.017

This study aims to review the ADS design based on the outcome for the last dozen years and to investigate the impact of impurities in the transmutation cycle on the ADS neutronics design. The impact of impurities in the transmutation cycle is investigated for the reviewed reference design. For the uranium from the partitioning, the accompaniment of 20 wt.% U against the Pu weight is acceptable although the MA transmutation amount will be decreased slightly. For the rare earth (RE) from the partitioning, the accompaniment of 5 wt.% RE against the MA weight is allowable. In the reprocessing, the decontamination factor, DF=10 for RE is enough from the viewpoint of the neutronics design. The impact of the fuel composition accuracy is also investigated. The uncertainty of the ZrN ratio against the MA fuel should be less than 0.2% to minimize a surplus proton beam current due to the uncertainty.

Tradeoff analysis of metal-fueled fast reactor design concepts

Stauff, N. E.*; Ohgama, Kazuya; Aliberti, G.*; Oki, Shigeo; Kim, T. K.*

Proceedings of 2017 International Congress on Advances in Nuclear Power Plants (ICAPP 2017) (CD-ROM), 10 Pages, 2017/04

Development of the versatile reactor analysis code system, MARBLE2

Yokoyama, Kenji; Jin, Tomoyuki; Hirai, Yasushi*; Hazama, Taira

JAEA-Data/Code 2015-009, 120 Pages, 2015/07

JAEA-Data-Code-2015-009.pdf:1.93MB

The second version of the versatile reactor analysis code system, MARBLE2, has been developed. A lot of new functions have been added inMARBLE2 by using the base technology developed in the first version (MARBLE1). Introducing the remaining functions of the conventional code system (JOINT-FR and SAGEP-FR), MARBLE2 enables one to execute almost all analysis functions of the conventional code system with the unified user interfaces of its subsystem, SCHEME. In particular, the sensitivity analysis functionality is available in MARBLE2. On the other hand, new built-in solvers have been developed, and existing ones have been upgraded. Furthermore, some other analysis codes and libraries developed in JAEA have been consolidated and prepared in SCHEME. In addition, several analysis codes developed in the other institutes have been additionally introduced as plug-in solvers. Consequently, -ray transport calculation and heating evaluation become available. As for another subsystem, ORPHEUS, various functionality updates and speed-up techniques have been applied based on user experience of MARBLE1 to enhance its usability.

Neutronics design of the low aspect ratio tokamak reactor, VECTOR

Nishitani, Takeo; Yamauchi, Michinori*; Nishio, Satoshi; Wada, Masayuki*

Fusion Engineering and Design, 81(8-14), p.1245 - 1249, 2006/02

https://doi.org/10.1016/j.fusengdes.2005.09.059

no abstracts in English

Key achievements in elementary R&D on water-cooled solid breeder blanket for ITER test blanket module in JAERI

Suzuki, Satoshi; Enoeda, Mikio; Hatano, Toshihisa; Hirose, Takanori; Hayashi, Kimio; Tanigawa, Hisashi; Ochiai, Kentaro; Nishitani, Takeo; Tobita, Kenji; Akiba, Masato

Nuclear Fusion, 46(2), p.285 - 290, 2006/02

https://doi.org/10.1088/0029-5515/46/2/012

This paper presents significant progress in R&D of key technologies on the water-cooled solid breeder blanket for the ITER-TBM in JAERI. By the improvement of heat treatment process for blanket module fabrication, a fine-grained microstructure of F82H, can be obtained by homogenizing it at 1150 C followed by normalizing at 930 C after the HIP process. Moreover, a promising bonding process for a tungsten armor and an F82H structural material was developed by using a uniaxial hot compression without any artificial compliant layer. Also, it has been confirmed that a fatigue lifetime correlation, which was developed for ITER divertor, can be applicable for F82H first wall mock-up. As for R&D on a breeder material, LiTiO, the effect of compression loads on thermal conductivity of pebble beds has been clarified. JAERI have extensively developed key technologies for ITER-TBM, and now steps up into an engineering R&D stage, where integrated performance of TBM structures will be demonstrated by scalable mock-ups.