検索対象:     
報告書番号:
※ 半角英数字
 年 ~ 
 年
検索結果: 7 件中 1件目~7件目を表示
  • 1

発表形式

Initialising ...

選択項目を絞り込む

掲載資料名

Initialising ...

発表会議名

Initialising ...

筆頭著者名

Initialising ...

キーワード

Initialising ...

使用言語

Initialising ...

発行年

Initialising ...

開催年

Initialising ...

選択した検索結果をダウンロード

論文

Observation and evaluation of plastic collapse for double-notch pipe

鈴木 良祐*; 松原 雅昭*; 坂本 賢治*; 鈴木 将人*; 白石 泰祐*; 柳原 星児*; 伊沢 悟*; 若井 隆純

Experimental Techniques, 40(1), p.253 - 260, 2016/09

 被引用回数:0 パーセンタイル:0.03(Engineering, Mechanical)

軸方向に垂直な2つの90度貫通切欠きを持つオーステナイト系ステンレス鋼管の塑性崩壊挙動と強度を調べた。様々なノッチ間距離で二つのノッチ試験片を光塑性フィルムで覆った。試験片には、軸方向の引張荷重と曲げ荷重を任意に組み合わせた荷重を加えた。塑性崩壊挙動を調査するために、試験中に光塑性フリンジパターンの変化が観察された。塑性崩壊強度は、弾完全塑性体に基づくモデルを用いて評価した。実験的な塑性崩壊点での光塑性フリンジパターンは荷重履歴によって異なった。このことから、塑性崩壊挙動は荷重履歴に依存することがわかった。一方、塑性崩壊強度はノッチ間距離にはほとんど依存しなかった。実験的な塑性崩壊は、いくつかの純引張荷重試験でのみ理論塑性点に達する前に発生した。したがって、この研究で使用された弾完全塑性体に基づくモデル解析は、純粋な引張荷重を受けるステンレス鋼管の塑性崩壊には非保守的な推定を与える可能性がある。

論文

Density and X-ray emission profile relationships in highly ionized high-Z laser-produced plasmas

吉田 健祐*; 藤岡 慎介*; 東口 武史*; 鵜篭 照之*; 田中 のぞみ*; 川崎 将人*; 鈴木 悠平*; 鈴木 千尋*; 富田 健太郎*; 廣瀬 僚一*; et al.

Applied Physics Letters, 106(12), p.121109_1 - 121109_5, 2015/03

 被引用回数:8 パーセンタイル:34.82(Physics, Applied)

We present a benchmark measurement of the electron density profile in the region where the electron density is 10$$^{19}$$ cm$$^{-3}$$ and where the bulk of extreme ultraviolet (EUV) emission occurs from isotropically expanding spherical high-Z gadolinium plasmas. It was found that, due to opacity effects, the observed EUV emission is mostly produced from an underdense region. We have analyzed time-resolved emission spectra with the aid of atomic structure calculations, and find that while the multiple ion charge states around 18+ during the laser pulse irradiation.

論文

Efficient extreme ultraviolet emission from one-dimensional spherical plasmas produced by multiple lasers

吉田 健祐*; 藤岡 慎介*; 東口 武史*; 鵜篭 照之*; 田中 のぞみ*; 大橋 隼人*; 川崎 将人*; 鈴木 悠平*; 鈴木 千尋*; 富田 健太郎*; et al.

Applied Physics Express, 7(8), p.086202_1 - 086202_4, 2014/08

 被引用回数:28 パーセンタイル:73.87(Physics, Applied)

半導体デバイスには更なる高性能化, 小型化が求められておりノードの微細化は急務となっている。さらなる細線化を目指して波長6.5-6.7nmの極端紫外光源の研究開発に着手している。極端紫外光源を実現させるために最も重要な開発課題は、光源の高出力化であり、本研究では球状ターゲットにレーザーを球対称に12方向から同時にターゲットに照射することで球対称なプラズマを生成させ6.5-6.7nm帯域の放射特性を調べた。本実験では変換効率のレーザー照射強度依存性をスペクトル, 電子密度, イオン価数, 電子温度など様々なパラメータから考察することでリソグラフィに求められる光源として最適なプラズマの生成条件の研究を行った。ガドリニウムターゲットの最適なレーザー照射強度に対する変換効率として、これまでの研究報告の中で最高の0.8%が得られた。

論文

軸力と曲げを受ける切欠付ステンレス配管の塑性崩壊強度及び最大荷重評価

柳原 星児*; 松原 雅昭*; 鈴木 良祐*; 鈴木 将人*; 白石 太祐*; 坂本 賢治*; 若井 隆純

日本機械学会M&M2012材料力学カンファレンス講演論文集(CD-ROM), 2 Pages, 2012/09

The fracture assessment of independent multiple flaws is not developed in the piping for nuclear power in the Japan Society of Mechanical Engineers maintenance standard. In the maintenance standard, an enough examination is not performed about the influence that the load history of the axial tension due to inner pressure and the bending such as the earthquake affects on collapse strength of the piping. This study clarified that the effect of multiple flaws affected on the plastic collapse strength of the stainless steel piping that loaded axial tension and bending independently, and proposed the maximum load evaluation method. Conclusions are as follows: (1) Multiple flaws on piping can be evaluated by the plastic collapse theory of the single flaw, and the flaw can be simplified, and a conservative evaluation of piping be done. (2) The maximum stress can be calculated from the flaw size and mechanical properties of piping and piping size.

論文

軸力と曲げを受ける周方向複数切欠を有するSUS304鋼配管の塑性崩壊強度

白石 太祐*; 松原 雅昭*; 鈴木 良祐*; 鈴木 将人*; 柳原 星児*; 坂本 賢治*; 若井 隆純

日本機械学会M&M2012材料力学カンファレンス講演論文集(CD-ROM), 3 Pages, 2012/09

The aim of this study is to investigate the effect of notch interval on plastic collapse strength of the type 304 stainless steel piping and simplify the flaw assessment method of type 304 stainless steel piping subjected to combined tension and bending. Typical loads applied to type 304 stainless steel piping are axial tension due to internal pressure and bending load caused by external forces. Two 90 degree through-wall notches were machined perpendicular to the axial direction of the pipe with interval, $$L$$$$_{rm N}$$, from 1 to 28 mm. The experimental plastic collapse strength of the specimens with single notch and two notches were higher than the theoretical ones of the single notched pipe assumed elastic perfectly plastic body. Therefore, it was clarified that the plastic collapse strengths of type 304 stainless steel pipes with two notches perpendicular to the pipe axis can be evaluated safely using the theoretical ones of the single notched pipe assumed elastic perfectly plastic body.

論文

Collapse strength of multiple notched pipes under combined load

白石 太祐*; 松原 雅昭*; 鈴木 良祐*; 鈴木 将人*; 若井 隆純; 坂本 賢治*

Proceedings of 5th International Workshop New Methods of Damage and Failure Analysis of Structural Parts (CD-ROM), 6 Pages, 2012/09

The aim of this study is to investigate the effect of notch interval on plastic collapse strength of the type 304 stainless steel piping and simplify the flaw assessment method of type 304 stainless steel piping subjected to combined tension and bending. Typical loads applied to type 304 stainless steel piping are axial tension due to internal pressure and bending load caused by external forces. The plastic collapse strengths of the notched specimen subjected to arbitrary combined axial tension and bending loads were evaluated. Two 90 degree through-wall notches were machined perpendicular to the pipe axis with interval from 1 to 28 mm. It was clarified that the plastic collapse strengths of type 304 stainless steel pipes with two notches perpendicular to the pipe axis can be evaluated safely using the theoretical plastic collapse strength of the pipe with single notch assuming elastic perfectly plastic body.

論文

軸力と曲げを受けるステンレス配管の塑性崩壊強度に関する研究

松原 雅昭*; 林 達也*; 鈴木 将人*; 白石 太祐*; 坂本 賢治*; 若井 隆純

日本機械学会M&M2011材料力学カンファレンス講演論文集(CD-ROM), 2 Pages, 2011/07

本研究では、原子力設備の安全性向上に寄与するため、複数欠陥がステンレス鋼管の塑性崩壊強度に及ぼす影響について調べた。複数欠陥を有する配管の塑性崩壊荷重を知ることは重要である。そこで、簡単のために、複数欠陥を単一欠陥でモデル化することを目的として、単一及び複数の欠陥を有する管に対して、引張及び曲げ荷重が重畳する実験を行った。その結果、(1)複数欠陥を単一欠陥にモデル化することにより保守的に評価可能であることがわかった、(2)いずれの荷重条件においても、並列欠陥は単一欠陥に置き換えて考えることが可能であることがわかった。

7 件中 1件目~7件目を表示
  • 1