検索対象:     
報告書番号:
※ 半角英数字
 年 ~ 
 年
検索結果: 92 件中 1件目~20件目を表示

発表形式

Initialising ...

選択項目を絞り込む

掲載資料名

Initialising ...

発表会議名

Initialising ...

筆頭著者名

Initialising ...

キーワード

Initialising ...

発表言語

Initialising ...

発行年

Initialising ...

開催年

Initialising ...

選択した検索結果をダウンロード

論文

Microstructural evolution and mechanical instability of Mar-M509 superalloy fabricated by laser powder bed fusion under short-term thermal exposure

Cao, T.*; Wei, D.*; Gong, W.; 川崎 卓郎; Harjo, S.; 他10名*

Materials Science and Engineering A, 940, p.148534_1 - 148534_16, 2025/09

The thermal stability of microstructure and mechanical performance is crucial for the industrial application of laser powder bed fusion (LPBF) superalloy components in gas turbines and jet engines. This work investigated the microstructural evolution and strengthening mechanism of LPBF Mar-M509 cobalt-based superalloy before and after thermal exposure at 1200 $$^{circ}$$C using multi-scale microstructural characterization and in situ neutron diffraction tensile testing. The as-built Mar-M509 superalloy exhibited a heterogeneous microstructural features with coarse columnar and fine equiaxed grains, both containing dendritic and cellular substructures enriched with nanoscale carbides and high-density dislocations. The ultra high strength of the as-built sample was primarily attributed to dislocation-precipitation synergistic strengthening. After thermal exposure at 1200 $$^{circ}$$C for 4 h, the dendritic and cellular substructures disappeared and the dislocation density decreased significantly. This study reveals the microstructural evolution and instability of LPBF Mar-M509 superalloy under high-temperature exposure and the impacts on mechanical properties, which provides critical support for the development of cobalt-based superalloys in high-temperature application fields.

論文

Enhanced work hardening in ferrite and austenite of duplex stainless steel at 200 K; ${it In situ}$ neutron diffraction study

山下 享介*; 古賀 紀光*; Mao, W.*; Gong, W.; 川崎 卓郎; Harjo, S.; 藤井 英俊*; 梅澤 修*

Materials Science and Engineering A, 941, p.148602_1 - 148602_11, 2025/09

 被引用回数:0

Ferrite-austenite duplex stainless steels offer excellent strength and ductility, making them suitable for extreme environments. In this study, ${it in situ}$ neutron diffraction during tensile testing at 293 K and 200 K was used to investigate stress partitioning and phase-specific deformation. Phase stress was calculated using a texture-compensated method. At both temperatures, ferrite showed higher phase stress than austenite, acting as the harder phase. At 200 K, both phases exhibited increased strength and work hardening. Austenite showed significant stacking fault formation alongside dislocation migration, while ferrite retained its dislocation-based deformation mode, becoming more effective. Stress contributions from both phases were comparable. No martensitic transformation occurred. Strengthening and enhanced work hardening in both phases led to high strength at 200 K, with ductility similar to that at 293 K.

論文

Role of solute hydrogen on mechanical property enhancement in Fe-24Cr-19Ni austenitic steel; An ${it in situ}$ neutron diffraction study

伊東 達矢; 小川 祐平*; Gong, W.; Mao, W.*; 川崎 卓郎; 岡田 和歩*; 柴田 曉伸*; Harjo, S.

Acta Materialia, 287, p.120767_1 - 120767_16, 2025/04

 被引用回数:1 パーセンタイル:0.00(Materials Science, Multidisciplinary)

Incorporating solute hydrogen into Fe-Cr-Ni-based austenitic stainless steels enhances both strength and ductility, providing a promising solution to hydrogen embrittlement by causing solid-solution strengthening and assisting deformation twinning. However, its impacts on the relevant lattice defects evolution (${it i.e.}$, dislocations, stacking faults, and twins) during deformation remains unclear. This study compared the tensile deformation behavior in an Fe-24Cr-19Ni (mass%) austenitic steel with 7600 atom ppm hydrogen-charged (H-charged) and without hydrogen-charged (non-charged) using ${it in situ}$ neutron diffraction. Hydrogen effects on the lattice expansion, solid-solution strengthening, stacking fault probability, stacking fault energy, dislocation density, and strain/stress for twin evolution were quantitatively evaluated to link them with the macroscale mechanical properties. The H-charged sample showed improvements in yield stress, flow stress, and uniform elongation, consistent with earlier findings. However, solute hydrogen exhibited minimal influences on the evolution of dislocation and stacking fault. This fact contradicts the previous reports on hydrogen-enhanced dislocation and stacking fault evolutions, the latter of which can be responsible for the enhancement of twinning. The strain for twin evolution was smaller in the H-charged sample compared to the non-charged one. Nevertheless, when evaluated as the onset stress for twin evolution, there was minimal change between the two samples. These findings suggest that the increase in flow stress due to the solid-solution strengthening by hydrogen is a root cause of accelerated deformation twinning at a smaller strain, leading to an enhanced work-hardening rate and improved uniform elongation.

論文

Enhanced strength and ductility in an additively manufactured Al10SiMg alloy at cryogenic temperatures

Naeem, M.*; Rehman, A. U.*; Romero Resendiz, L.*; Salamci, E.*; Aydin, H.*; Ansari, P.*; Harjo, S.; Gong, W.; Wang, X.-L.*; 他3名*

Communications Materials (Internet), 6, p.65_1 - 65_13, 2025/04

The need for lightweight materials with mechanical integrity at ultralow temperatures drives the development of advanced alloys for cryogenic use. Additive manufacturing via laser powder bed fusion (LPBF) offers a scalable way to create alloys with tailored properties. Here, we show that LPBF-processed Al10SiMg exhibits a high ultimate tensile strength (395 MPa) and uniform elongation (25%) at 15 K. These enhancements stem from grain refinement, increased geometrically necessary dislocations, and stress partitioning between the Al matrix and the stiffer Si phase, aiding strain accommodation. ${it In-situ}$ neutron diffraction reveals that the Si phase, with its higher yield strength, bears most of the load, while the Al matrix undergoes continuous strain hardening, extending deformation capacity. These results highlight Al10SiMg's promise for cryogenic applications such as hydrogen storage, aerospace, and quantum computing hardware.

論文

Unusual low-temperature ductility increase mediated by dislocations alone

Naeem, M.*; Ma, Y.*; Tian, J.*; Kong, H.*; Romero-Resendiz, L.*; Fan, Z.*; Jiang, F.*; Gong, W.; Harjo, S.; Wu, Z.*; et al.

Materials Science & Engineering A, 924, p.147819_1 - 147819_10, 2025/02

 被引用回数:1 パーセンタイル:0.00(Nanoscience & Nanotechnology)

Face-centered cubic (fcc) medium-/high-entropy alloys (M/HEAs) typically enhance strength and ductility at cryogenic temperatures via stacking faults, twinning, or martensitic transformation. However, in-situ neutron diffraction on VCoNi MEA at 15 K reveals that strain hardening is driven solely by rapid dislocation accumulation, without these mechanisms. This results in increased yield strength, strain hardening, and fracture strain. The behavior, explained by the Orowan equation, challenges conventional views on cryogenic strengthening in fcc M/HEAs and highlights the role of dislocation-mediated plasticity at low temperatures.

論文

Characteristic deformation microstructure evolution and deformation mechanisms in face-centered cubic high/medium entropy alloys

吉田 周平*; Gong, W.; 他9名*

Acta Materialia, 283, p.120498_1 - 120498_15, 2025/01

 被引用回数:3 パーセンタイル:57.76(Materials Science, Multidisciplinary)

Face-centered cubic (FCC) high/medium entropy alloys (HEAs/MEAs), novel multi-principal element alloys, are known to exhibit exceptional mechanical properties at room temperature; however, the origin is still elusive. Here, we report the deformation microstructure evolutions in a tensile-deformed Co$$_{20}$$Cr$$_{40}$$Ni$$_{40}$$ representative MEA and Co$$_{60}$$Ni$$_{40}$$ alloy, a conventional binary alloy for comparison. These FCC alloys have high/low friction stresses, and share similar other material properties. The Co$$_{20}$$Cr$$_{40}$$Ni$$_{40}$$ MEA exhibited higher yield strength and work-hardening ability than in the Co$$_{60}$$Ni$$_{40}$$ alloy. Deformation microstructures in the Co$$_{20}$$Cr$$_{40}$$Ni$$_{40}$$ alloy were marked by the presence of coarse dislocation cells (DCs) regardless of grain orientation and a few deformation twins (DTs) in grains with the tensile axis (TA) near $$<$$1 1 1$$>$$. In contrast, the MEA developed three distinct deformation microstructures depending on grain orientations: fine DCs in grains with the TA near $$<$$1 0 0$$>$$, planar dislocation structure (PDS) in grains with other orientations, and a high density of DTs along with PDS in grains oriented $$<$$1 1 1$$>$$. These findings demonstrate that FCC HEAs/MEAs with high friction stresses naturally develop unique deformation microstructures which is beneficial for realizing superior mechanical properties compared to conventional materials.

論文

Role of retained austenite and deformation-induced martensite in 0.15C-5Mn steel monitored by ${it in situ}$ neutron diffraction measurement during tensile deformation

山下 享介*; 諸岡 聡; Gong, W.; 川崎 卓郎; Harjo, S.; 北條 智彦*; 興津 貴隆*; 藤井 英俊*

ISIJ International, 64(14), p.2051 - 2060, 2024/12

 被引用回数:0

An Fe-0.15C-5Mn-0.5Si-0.05Nb steel annealed at 660$$^{circ}$$C and 685$$^{circ}$$C showed L$"u$ders deformation followed by high work hardening, with variations in L$"u$ders strain and hardening behavior. ${it In situ}$ neutron diffraction during tensile tests analyzed phase stresses, strength contributions, and austenite orientation. Deformation-induced martensite contributed $$sim$$1000 MPa to strength near tensile failure, while austenite mainly enhanced ductility via transformation-induced plasticity. Austenite transformed to martensite during L$"u$ders deformation regardless of orientation, though 311-oriented grains tended to remain along the tensile direction.

論文

Enhanced cryogenic mechanical properties of heterostructured CrCoNi multicomponent alloy; Insights from ${it in situ}$ neutron diffraction

Naeem, M.*; Ma, Y.*; Knowles, A. J.*; Gong, W.; Harjo, S.; Wang, X.-L.*; Romero Resendiz, L.*; 他6名*

Materials Science & Engineering A, 916, p.147374_1 - 147374_8, 2024/11

 被引用回数:3 パーセンタイル:57.76(Nanoscience & Nanotechnology)

Heterostructured materials (HSMs) improve the strength-ductility trade-off of alloys, but their cryogenic performance under real-time deformation is unclear. We studied heterostructured CrCoNi medium-entropy alloy via ${it in situ}$ neutron diffraction at 77 K and 293 K. A significant mechanical mismatch between fine and coarse grains led to an exceptional yield strength of 918 MPa at 293 K, increasing to 1244 MPa at 77 K with a uniform elongation of 34%. This strength-ductility synergy at 77 K is attributed to high dislocation pile-up density, increased planar faults, and martensitic transformation. Compared to homogeneous alloys, HSMs show promise for enhancing cryogenic mechanical performance in medium-/high-entropy alloys.

論文

${it In situ}$ neutron diffraction study to elucidate hydrogen effect on the deformation mechanism in Type 310S austenitic stainless steel

伊東 達矢; 小川 祐平*; Gong, W.; Mao, W.*; 川崎 卓郎; 岡田 和歩*; 柴田 曉伸*; Harjo, S.

Proceedings of the 7th International Symposium on Steel Science (ISSS 2024), p.237 - 240, 2024/11

Hydrogen embrittlement has long been an obstacle to the development of safe infrastructure. However, in contrast to hydrogen's embrittling effect, recent research has revealed that the addition of hydrogen improves both the strength and uniform elongation of AISI Type 310S austenitic stainless steel. A detailed understanding of how hydrogen affects the deformation mechanism of this steel could pave the way for the development of more advanced materials with superior properties. In the present study, ${it in situ}$ neutron diffraction experiments were conducted on Type 310S steel with and without hydrogen-charged to investigate the effect of hydrogen on the deformation mechanism. In addition to the effect of solid-solution strengthening by hydrogen, the q-value, a parameter representing the proportion of edge and screw dislocations in the accumulated dislocations, was quantitatively evaluated using CMWP analysis on neutron diffraction patterns. The comparison of q-values between the hydrogen-charged and non-charged samples reveals that hydrogen has minimal effect on dislocation character in Type 310S steel.

論文

Internal strain measurement by neutron diffraction under transverse compressive stress for Nb$$_{3}$$Sn wires with and without Cu-Nb reinforcement

中本 美緒*; 菅野 未知央*; 荻津 透*; 杉本 昌弘*; 谷口 諒*; 廣瀬 清慈*; 川崎 卓郎; Gong, W.; Harjo, S.; 淡路 智*; et al.

IEEE Transactions on Applied Superconductivity, 34(5), p.8400806_1 - 8400806_6, 2024/08

 被引用回数:0 パーセンタイル:0.00(Engineering, Electrical & Electronic)

For an accelerator magnet, a certain mechanical strength is required to sustain against a transverse compression stress due to Lorentz force. A bronze-route Nb$$_{3}$$Sn wire with Cu-Nb reinforcement was developed by Tohoku University and Furukawa Electric to enhance the strength against axial tension. The Cu-Nb reinforcement wire also exhibited some indication of strength improvement against transverse compression; however, the details of a reinforcement mechanism for the transverse compression stress have not been clarified. In this study, the internal strains of Nb$$_{3}$$Sn bronze-route wires with and without the Cu-Nb reinforcement under transverse compression stress were evaluated by neutron diffraction at BL19 (TAKUMI) in J-PARC. The samples were attached to jig with solder only at the ends and compression was applied at the center of the samples with 30-mm anvil with 5-mm wide and 8- to 15-mm high beam. Since a critical current, Ic of a superconducting wire depends on the three-dimensional strain, internal strain of Nb$$_{3}$$Sn along the axial and two orthogonal radial directions were evaluated at room temperature (RT). In the different setup, Ic measurements of the wires under transverse compression stresses were also performed at 4.2 K and 14.5 T. Using 3-mm wide anvil, the transverse compression was applied at 4.2 K or RT. The neutron diffraction results indicated no significant differences in the internal strains of Nb$$_{3}$$Sn under transverse compression between the samples with and without Cu-Nb reinforcement, while the Ic measurements showed potential increase in the irreversible stress ($$sigma$$$$_{irr}$$) for Cu-Nb reinforced wires. The reason for this discrepancy was discussed based on the difference in the experimental setups for each measurement.

論文

Effects of loading direction on the anisotropic tensile properties of duplex stainless steels based on phase strains obtained by in situ neutron diffraction experiments

松下 慧*; 土田 紀之*; 石丸 詠一郎*; 平川 直樹*; Gong, W.; Harjo, S.

Journal of Materials Engineering and Performance, 33(13), p.6352 - 6361, 2024/07

 被引用回数:2 パーセンタイル:9.61(Materials Science, Multidisciplinary)

This study investigated the anisotropy of the tensile properties in a duplex stainless steel of 24Cr-5Ni-0.18N based on in situ neutron diffraction experiments. The 24Cr-5Ni-0.18N steel showed a better balance of tensile strength (TS) and uniform elongation (U.El) compared with 329J4L and 329J1 steels. The Lankford value ($$r$$-value) of the 24Cr-5Ni-0.18N steel was comparable to other duplex stainless steels while showing a larger TS. Regarding the anisotropy of the mechanical properties, the results for a test specimen oriented at 45$$^{circ}$$ showed a low yield strength (YS) and TS, but a better U.El and $$r$$-value. The neutron diffraction results are discussed to explain the mechanical properties.

論文

Dual nanoprecipitation and nanoscale chemical heterogeneity in a secondary hardening steel for ultrahigh strength and large uniform elongation

Wang, S.*; Wang, J.*; Zhang, S.*; Wei, D.*; Chen, Y.*; Rong, X.*; Gong, W.; Harjo, S.; Liu, X.*; Jiao, Z.*; et al.

Journal of Materials Science & Technology, 185, p.245 - 258, 2024/06

 被引用回数:17 パーセンタイル:98.00(Materials Science, Multidisciplinary)

Nanoprecipitates and nanoscale retained austenite (RA) with suitable stability play crucial roles in determining the yield strength (YS) and ductility of ultrahigh strength steels (UHSSs). However, owing to the kinetics incompatibility between nanoprecipitation and austenite reversion, it is highly challenging to simultaneously introduce high-density nanoprecipitates and optimized RA in UHSSs. In this work, through the combination of austenite reversion treatment (ART) and subsequent flash austenitizing (FA), nanoscale chemical heterogeneity was successfully introduced into a low-cost UHSS prior to the aging process. This chemical heterogeneity involved the enrichment of Mn and Ni in the austenite phase. The resulting UHSS exhibited dual-nanoprecipitation of Ni(Al,Mn) and (Mo,Cr)$$_{2}$$ C and nanoscale austenite stabilized via Mn and Ni enrichment. The hard martensitic matrix strengthened by high-density dual-nanoprecipitates constrains the plastic deformation of soft RA with a relatively low fraction, and the presence of relatively stable nanoscale RA with adequate Mn and Ni enrichment leads to a marginal loss in YS but keeps a persistent transformation-induced plasticity (TRIP) effect. As a result, the newly-developed UHSS exhibits an ultrahigh YS of 1.7 GPa, an ultimate tensile strength (UTS) of 1.8 GPa, a large uniform elongation (UE) of 8.5 percent, and a total elongation (TE) of 13 percent. The strategy of presetting chemical heterogeneity to introduce proper metastable phases before aging can be extended to other UHSSs and precipitation-hardened alloys.

論文

Cryogenic deformation behavior of a dual-phase Mg-Li alloy investigated by in-situ neutron diffraction

Gong, W.; Gholizadeh, R.*; 川崎 卓郎; 相澤 一也; Harjo, S.

Magnesium Technology 2024, p.89 - 90, 2024/03

Mg and its alloys generally exist as a single hcp crystal structure at room temperature. It is widely recognized that the application of Mg alloys is hindered by their limited formability at room temperature, primarily attributable to the scarcity of readily activated deformation modes within the hcp phase. The addition of Li in Mg alloy can stable the bcc phase at room temperature, and these dual-phase (hcp+bcc) Mg-Li alloys exhibit excellent formability. The Li-enriched bcc phase has been frequently considered as the origin for improving formability. However, these Mg-Li alloys show poor work-hardening ability and the resultant low strength at room temperature. Considering that the dislocation recovery can be suppressed by decreasing the deformation temperature and the activity of deformation mode may be changed with temperature, we investigated the deformation behavior of a commercial LZ91 magnesium alloy at cryogenic temperatures using in-situ neutron diffraction.

論文

Role of retained austenite and deformation induced martensite in 0.15C-5Mn steel monitored by ${it in-situ}$ neutron diffraction measurement during tensile deformation

山下 享介*; 諸岡 聡; Gong, W.; 川崎 卓郎; Harjo, S.; 北條 智彦*; 興津 貴隆*; 藤井 英俊*

鉄と鋼, 110(3), p.241 - 251, 2024/02

 被引用回数:0 パーセンタイル:0.00(Metallurgy & Metallurgical Engineering)

A Fe-0.15C-5Mn-0.5Si-0.05Nb medium Mn steel annealed at 660$$^{circ}$$C and 685$$^{circ}$$C both exhibited inhomogeneous deformation with Luders deformation and extremely high work hardening rates, but with different Luders strain and work hardening behavior. ${it In-situ}$ neutron diffraction measurements during tensile test were performed to investigate changes in the phase stresses and in the contributed stresses to the strength of the constituent phases, and crystal orientation of austenite. The role of each constituent phase in the deformation and the effect of crystallographic orientation on austenite stability were discussed. Deformation induced martensite showed excellent phase stress and contributed to the strength approximately 1000 MPa, which is close to macroscopic tensile strength.

論文

Deformation-induced martensitic transformation at tensile and compressive deformations of bainitic steels with different carbon contents

上路 林太郎*; Gong, W.; Harjo, S.; 川崎 卓郎; 柴田 曉伸*; 木村 勇次*; 井上 忠信*; 土田 紀之*

ISIJ International, 64(2), p.459 - 465, 2024/01

 被引用回数:1 パーセンタイル:36.18(Metallurgy & Metallurgical Engineering)

Deformation-induced martensitic transformation (DIMT) during tensile or compressive deformations of the bainitic steels with various carbon content (0.15%C, 0.25%C, 0.62%C) was studied. In all of the bainitic steels, the tensile deformation exhibited larger work hardening than the compression. This difference indicates the suppression of the DIMT at the compression, and actually the measurements of electron back scattering diffraction (EBSD) confirmed the less reduction of retained austenite at the compression of all the bainitic steels. Additionally, the steel with the highest carbon content was examined by in situ neutron diffraction and clarified the difference similar to that obtained by the EBSD measurement. The regression of the relation between the fraction of austenite and applied strain with the conventional empirical equation revealed that the kinetic of DIMT is strongly dependent with the stress polarity, but not significantly changed by the carbon content.

論文

Change in mechanical properties of high-strength martensitic steel by the combination of pre-strain and deformation temperature

土田 紀之*; Kuramoto, Shota*; 上路 林太郎*; Gong, W.; Harjo, S.; 廣井 孝介; 河村 幸彦*

ISIJ International, 64(2), p.354 - 360, 2024/01

 被引用回数:0 パーセンタイル:0.00(Metallurgy & Metallurgical Engineering)

The effects of pre-strain on the mechanical properties of high strength martensitic steels were investigated using either strain tempering (ST) or quenching and tempering (QT) samples. In the tensile tests at deformation temperatures between 296 and 573 K, the ST sample exhibited an increase in both the tensile strength (TS) and uniform elongation (U El) at 473 to 523 K, whereas the QT sample showed an increase in U El with little change in the TS and yield strength (YS). The results of in situ neutron diffraction experiments revealed an increase in the stress partitioning to the bcc phase with an increase in the deformation temperature from 296 to 523 K. The difference in the phase stress between the bcc and cementite phases decreased with an increase in the temperature due to the decrease in the cementite strength. Pre-strain of 0.5% increased the YS at 296 K with a slight work hardening; the initial dislocation density ($$rho$$) decreased at 523 K, but increased significantly after yielding, leading to a better combination of TS and U.El. The combination of pre-strain, tempering, and deformation temperatures caused the change in $$rho$$ before deformation and the increase in $$rho$$ after yielding of the martensitic steel.

論文

Martensitic transformation behavior of Fe-Ni-C alloys monitored by ${it in-situ}$ neutron diffraction during cryogenic cooling

山下 享介*; Harjo, S.; 川崎 卓郎; 諸岡 聡; Gong, W.; 藤井 英俊*; 友田 陽*

ISIJ International, 64(2), p.192 - 201, 2024/01

 被引用回数:1 パーセンタイル:0.00(Metallurgy & Metallurgical Engineering)

${it In situ}$ neutron diffraction measurements were performed on Fe-33Ni-0.004C alloy (33Ni alloy) and Fe-27Ni-0.5C alloy (27Ni-0.5C alloy) during cooling from room temperature to the cryogenic temperature (4 K) to evaluate changes in the lattice constants of austenite and martensite, and changes in the tetragonality of martensite due to thermally induced martensitic transformation. As the martensitic transformation progressed, the lattice constants of austenite in both alloys deviated to smaller values than those predicted considering the thermal shrinkage, accompanied by an increase in the full width at half maximum of austenite. The fresh martensite formed in both alloys had a body-centered tetragonal (BCT) structure, regardless of the carbon content. The tetragonality of martensite decreased with progressive martensitic transformation during cooling in the 33Ni alloy, but was almost constant in the 27Ni-0.5C alloy. This suggests that carbon is necessary to maintain the tetragonality of martensite during cooling. The tetragonality of martensite in the 27Ni-0.5C alloy decreased during room temperature aging because of carbon mobility.

論文

Probing deformation behavior of a refractory high-entropy alloy using ${it in situ}$ neutron diffraction

Zhou, Y.*; Song, W.*; Zhang, F.*; Wu, Y.*; Lei, Z.*; Jiao, M.*; Zhang, X.*; Dong, J.*; Zhang, Y.*; Yang, M.*; et al.

Journal of Alloys and Compounds, 971, p.172635_1 - 172635_7, 2024/01

 被引用回数:3 パーセンタイル:23.52(Chemistry, Physical)

The grain orientation-dependent lattice strain evolution of a (TiZrHfNb)$$_{98}$$$$N_2$$ refractory high-entropy alloy (HEA) during tensile loading has been investigated using ${it in situ}$ neutron diffraction. The equivalent strain-hardening rate of each of the primary $$<hkl>$$-oriented grain families was found to be relatively low, manifesting the macroscopically weak work-hardening ability of such a body-centered cubic (BCC)-structured HEA. This finding is indicative of a dislocation planar slip mode that is confined in a few single-slip planes and leads to in-plane softening by high pile-up stresses.

論文

Effects of dislocation arrangement and character on the work hardening of lath martensitic steels

段野下 宙志*; 長谷川 寛*; 樋口 翔*; 松田 広志*; Gong, W.; 川崎 卓郎; Harjo, S.; 梅澤 修*

Scripta Materialia, 236, p.115648_1 - 115648_5, 2023/11

 被引用回数:3 パーセンタイル:34.67(Nanoscience & Nanotechnology)

Work-hardening behavior of a lath martensitic Fe-18Ni alloy during tensile deformation is discussed based on the Taylor's equation. The dislocation characteristics are monitored using in situ neutron diffraction. In the specimens of as-quenched (AQ) and tempered at 573 K (T573), the dislocations are extremely dense and randomly arranged. The dislocations in AQ and T573 form dislocation cells as deformation progresses. Consequently, a composite condition comprising cell walls and cell interiors is formed, and the coefficient $$alpha$$ in the Taylor's equation increases. Cells are already present in the specimen tempered at 773 K (T773), which has a low dislocation density and a large fraction of edge-type dislocations. As deformation continues, the dislocation density of T773 increases, its cell size decreases, and its composite condition become stronger. Simultaneously, the edge-type dislocation fraction decreases, keeping $$alpha$$ unchanged. Thus, both the dislocation arrangement and character affected $$alpha$$, thereby affecting the work-hardening behavior.

論文

${it In situ}$ neutron diffraction study on the deformation behavior of the plastic inorganic semiconductor Ag$$_{2}$$S

Wang, Y.*; Gong, W.; 川崎 卓郎; Harjo, S.; Zhang, K.*; Zhang, Z. D.*; Li, B.*

Applied Physics Letters, 123(1), p.011903_1 - 011903_6, 2023/07

 被引用回数:4 パーセンタイル:47.87(Physics, Applied)

Bulk Ag$$_{2}$$S is a plastic inorganic semiconductor at room temperature. It exhibits a compressive strain greater than 50%, which is highly different from brittle conventional counterparts, such as silicon. Here, we present the experimental investigation of the deformation behavior in a plastic inorganic semiconductor Ag$$_{2}$$S using ${it in situ}$ neutron diffraction during compressive deformation at room and elevated temperatures. At room temperature, the lattice strain partitioning among $$hkl$$-orientated grain families could be responsible for the significant work-hardening behavior in the bulk Ag$$_{2}$$S with a monoclinic structure. The rapid accumulation of lattice defects and remarkable development of the deformation texture suggest that dislocation slip promotes plasticity. At 453 K, a monoclinic phase transforms into a body-centered cubic phase. A stress plateau appears at $$sim$$-4.8 MPa, followed by a rehardening state. The deformation mode of bulk Ag$$_{2}$$S at the initial stage is likely attributable to the migration of silver ions, and as strain increases, it is closer to that of room temperature, leading to rehardening.

92 件中 1件目~20件目を表示