Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
, 
, and X-ray spectrum analysisOshima, Masumi*; Goto, Jun*; Hayakawa, Takehito*; Asai, Masato; Kin, Tadahiro*; Shinohara, Hirofumi*
Isotope News, (790), p.19 - 23, 2023/12
When analyzing samples that contain many radionuclides at various concentrations, such as radioactive waste or fuel debris, it is difficult to apply general spectrum analysis methods and is necessary to chemically separate each nuclide before quantifying it. The chemical separation is especially essential for analysis using a liquid scintillation counter (LSC). In this report, the authors explain the newly developed spectral determination method (SDM) in which the entire spectrum is fitted to quantify radioactivity of nuclides mixed in a sample. By applying the SDM to - and X-ray spectrum measured by LSC and -ray spectrum measured by Ge detector simultaneously, the authors demonstrated that radioactivity of 40 radionuclides mixed in a sample at concentrations varying by two orders could be quantified, which is useful to simplify chemical separation process in radionuclide quantification.
Fukaya, Yuji; Maruyama, Takahiro; Goto, Minoru; Ohashi, Hirofumi; Higuchi, Hideaki
JAEA-Research 2023-002, 19 Pages, 2023/06
JAEA-Research-2023-002.pdf:1.48MB
A study on disposal of waste derived from commercial High Temperature Gas-cooled Reactor ("HTGR") has been performed. Because of significant difference between the reprocessing of Light Water Reactor ("LWR") and that of HTGR due to difference in structures of the fuel, adoptability of the laws relating to reprocessing waste disposal, which is enacted for LWR, to HTGR waste should be confirmed. Then, we compared the technologies and waste of reprocessing and evaluated radioactivity concentration in graphite waste by activation and contamination based on whole core burn-up calculation. As a result, it was found that SiC residue waste should be disposed of into a geological repository as 2nd class designated radioactive waste in the Designated Radioactive Waste Final Disposal Act (Act No.117 of 2000), by way of amendment of the applicable order, same as hull and end-piece of LWR, and graphite waste should be shallowly disposed of than geological disposal as 2nd class waste for pit disposal in the Act on the Regulation of Nuclear Source Material, Nuclear Fuel Material and Reactors (Act No.166 of 1957) same as a channel box of LWR.
Fukaya, Yuji; Goto, Minoru; Ohashi, Hirofumi
Annals of Nuclear Energy, 181, p.109534_1 - 109534_10, 2023/02
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)Feasibility of reprocessing of High Temperature Gas-cooled Reactor (HTGR) spent fuel by existing Plutonium Uranium Redox EXtraction (PUREX) plant and technology has been investigated. The spent fuel dissolved solution includes approximately 3 times amount of uranium-235 and 1.5 times amount of protonium because of the 3 times higher burnup compared with that of Light Water Reactor (LWR). Then, the heavy metal of the spent fuel is planned to be diluted to 3.1 times by depleted uranium to satisfy the limitation of Rokkasho Reprocessing Plant (RRP) plant. In the present study, recoverability of uranium and plutonium with the dilution is confirmed by a simulation with a reprocessing process calculation code. Moreover, the case without the dilution from the economic perspective is investigated. As a result, the feasibility is confirmed without the dilution, and it is expected that the reprocessed amount is reduced to 1/3 compared with a diluted case even though the facility should be optimized from the perspective of mass flow and criticality.
Fukaya, Yuji; Okita, Shoichiro; Sasaki, Koei; Ueta, Shohei; Goto, Minoru; Ohashi, Hirofumi; Yan, X.
Nuclear Engineering and Design, 399, p.112033_1 - 112033_9, 2022/12
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)Kernel migration of TRi-structural ISOtropic (TRISO) fuel for High Temperature Gas-cooled Reactor (HTGR) has been analyzed to investigate the potential dominating effects. Kernel migration is a major fuel failure mode and dominant to determine the lifetime of the fuel for High Temperature engineering Test Reactor (HTTR). However, this study shows that the result and reliability depend on the evaluation method. The evaluation method used in this study takes into account of actual distribution of Coated Fuel Particles (CFPs) and the resulting heterogeneous fuel temperature calculation with such distribution. The result shows that the Kernel Migration Rate (KMR) is predicted to be about 10% less compared with the most conservative evaluation.
Fukaya, Yuji; Ohashi, Hirofumi; Sato, Hiroyuki; Goto, Minoru; Kunitomi, Kazuhiko
Nihon Genshiryoku Gakkai Wabun Rombunshi (Internet), 21(2), p.116 - 126, 2022/06
An improvement electricity generation cost evaluation method for High Temperature Gas-cooled Reactors (HTGRs) has been performed. Japan Atomic Energy Agency (JAEA) had completed the commercial HTGR concept named Gas Turbine High Temperature Reactor (GTHTR300) and the electricity generation cost evaluation method approximately a decade ago. The cost evaluation was developed based on the method of Federation of Electric Power Companies (FEPC). The FEPC method was drastically revised after the Fukushima Daiichi nuclear disaster. Moreover, the escalation of material and labor cost for the decade should be consider to evaluate the latest cost. Therefore, we revised the cost evaluation method for GTHTR300 and the cost was compared with that of Light Water Reactor (LWR). As a result, it was found that the electricity generation cost of HTGR of 7.9 yen/kWh is cheaper than that of LWR of 11.7 yen/kWh by approximately 30% at the capacity factor of 70%.
Fukaya, Yuji; Okita, Shoichiro; Nakagawa, Shigeaki; Goto, Minoru; Ohashi, Hirofumi
Annals of Nuclear Energy, 168, p.108911_1 - 108911_7, 2022/04
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)A power distribution monitoring system by using a moving detector for a core with a long neutron flight path has been proposed. High Temperature Gas-cooled Reactor (HTGR) and Fast Reactor (FR) has a long neutron flight path and the neutrons reach to detector far from fuel assembly in the center of the core unlike Light Water Reactor (LWR). By using the feature, power distribution can be observed with a few detectors by moving the detector and computed tomography technology similar to X-ray Computed Tomography (CT). For a small-sized core, the power distribution can be evaluated only by an ex-core neutron detector. For a large-sized core with inner detectors, the power distribution can be observed with a small number of in-core detectors even if the deployment is limited due to material integrity conditions such as temperature environment. The feasibility is numerically confirmed by simulations of the HTGR core and its detector response. It is expected to observe the power distribution in the core of HTGR and FR, which is difficult continuously to deploy in-core detectors because of high temperature and/or high irradiation damage.
Sasaki, Koei; Miura, Shuichiro*; Fukumoto, Kenichi*; Goto, Minoru; Ohashi, Hirofumi
Proceedings of 28th International Conference on Nuclear Engineering (ICONE 28) (Internet), 6 Pages, 2021/08
Cs-Bi and Cs-Sb absorbed graphite samples (Cs-Bi/graphite and Cs-Sb/graphite) were synthesized and their high temperature chemical stabilities were tested up to 1500
C by TG and analyzed by TEM-EDS for the development of Cs trap material in high temperature gas-cooled reactor (HTGR) fuel particles. It was observed that Cs was stabilized by Sb but not by Bi in the specimens after the TG test. A rapid weight loss from 800 to 1000C may be caused by evaporation of Cs (boiling point: 671C) was seen in the TG result of both specimens. Precipitated Cs-Sb substance in the graphite matrix were not resolved even after the 1500C heating. The chemical composition of the Cs-Sb was specified as Cs
Sb. The experimental results suggest that Sb have potential to be a Cs getter material in graphite matrix. Long term heating test should be performed to confirm adaptability of Sb for Cs trap material in HTGR fuel particles.
Fukaya, Yuji; Ueta, Shohei; Goto, Minoru; Ohashi, Hirofumi
Annals of Nuclear Energy, 151, p.107937_1 - 107937_9, 2021/02
Times Cited Count：2 Percentile：31.78(Nuclear Science & Technology)Feasibility study on Burnable Poison (BP) credit concept to High Temperature Gas-cooled Reactor (HTGR) fuel fabrication has been performed. By mixing BP into fuel material in the first place of fuel fabrication, criticality safety is ensured in the all fuel fabrication process even with high enrichment fuel such as 14 wt% used in commercial HTGR. However, the poison effect also prevents the criticality even in the HTGR core, and it may shorten cycle length and achievable burn-up of the core. Therefore, the effect is evaluated by whole core burn-up calculation. As a BP, boron, gadolinium, erbium, and hafnium are investigated. As a result, it is found that boron and gadolinium suit this concept and the 14 wt% fuel can be fabricated in the plant fabricating 9.9 wt% High Temperature engineering Test Reactor (HTTR) fuel. With the boron and gadolinium, the commercial HTGR fuel can be fabricated with the safety measure as same as Light Water Reactor (LWR) fuel facility to treat the fuel with the enrichment up to 5 wt%. Especially, gadolinium is significantly suitable to this concept due to the dependency to spectrum, and more enhanced safety measure is feasible as well.
Takeda, Tetsuaki*; Inagaki, Yoshiyuki; Aihara, Jun; Aoki, Takeshi; Fujiwara, Yusuke; Fukaya, Yuji; Goto, Minoru; Ho, H. Q.; Iigaki, Kazuhiko; Imai, Yoshiyuki; et al.
High Temperature Gas-Cooled Reactors; JSME Series in Thermal and Nuclear Power Generation, Vol.5, 464 Pages, 2021/02
As a general overview of the research and development of a High Temperature Gas-cooled Reactor (HTGR) in JAEA, this book describes the achievements by the High Temperature Engineering Test Reactor (HTTR) on the designs, key component technologies such as fuel, reactor internals, high temperature components, etc., and operational experience such as rise-to-power tests, high temperature operation at 950C, safety demonstration tests, etc. In addition, based on the knowledge of the HTTR, the development of designs and component technologies such as high performance fuel, helium gas turbine and hydrogen production by IS process for commercial HTGRs are described. These results are very useful for the future development of HTGRs. This book is published as one of a series of technical books on fossil fuel and nuclear energy systems by the Power Energy Systems Division of the Japan Society of Mechanical Engineers.
Mineo, Hideaki; Nishihara, Tetsuo; Ohashi, Hirofumi; Goto, Minoru; Sato, Hiroyuki; Takegami, Hiroaki
Nihon Genshiryoku Gakkai-Shi ATOMO
, 62(9), p.504 - 508, 2020/09
High-Temperature Gas-cooled Reactor (HTGR) is one of thermal neutron reactor-type that employs helium gas coolant and graphite moderator. It has excellent inherent safety and can supply high-temperature heat which can be used not only for electric power generation but also for a wide range of application such as hydrogen production. Therefore, HTGR is expected to be an effective technology for reducing greenhouse gases in Japan as well as overseas. In this paper, we will introduce the forefront of technological development that JAEA is working toward the realization of an HTGR system consisting of a high temperature gas reactor and heat utilization facilities such as gas-turbine power generation and hydrogen production.
-ray detection to long-lived radioactive nuclide determination in environmental samplesOshima, Masumi*; Goto, Jun*; Haraga, Tomoko; Kin, Tadahiro*; Ikebe, Yurie*; Seto, Hirofumi*; Bamba, Shigeru*; Shinohara, Hirofumi*; Morimoto, Takao*; Isogai, Keisuke*
Journal of Nuclear Science and Technology, 57(6), p.663 - 670, 2020/06
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)Gamma-gamma coincidence measurement utilized in -ray spectroscopy experiments is well known to be effective for the improvement of signal-to-noise ratio in a -ray spectrum. We study its applicability to determination of long-lived radioactive nuclides in environmental samples. The -ray simulation code Geant 4.10.2 was used. We took up 35 nuclides which need to be determined for the evaluation of fission product leakage at the nuclear accident in the Fukushima nuclear power plants. Among them five nuclides of 
Co, 
Nb, 
Cs, 
Eu and 
Eu can be the objectives of the multiple -ray detection method. The simulation results indicate that the signal-to-noise ratio can be improved by a factor between 9.8 and 283, and the detection limit by a factor between 2.7 and 8.5 relative to the singles measurement, implying that the method can be well applied to the determination of the long-lived radioactive nuclides.
Fukaya, Yuji; Mizuta, Naoki; Goto, Minoru; Ohashi, Hirofumi; Yan, X.
Nuclear Engineering and Design, 361, p.110577_1 - 110577_6, 2020/05
Times Cited Count：4 Percentile：45.45(Nuclear Science & Technology)Conceptual design study of a commercial High Temperature Gas-cooled Reactor (HTGR) for early introduction has been performed based on the cumulated experience in design, construction, and operation of the High Temperature engineering Test Reactor (HTTR) and design of the commercial Gas Turbine High Temperature Reactor 300 (GTHTR300). The power output is 165 MWt and the inlet and outlet coolant temperatures are 325C and 750C, respectively, to provide steam for industrial utilization. However, given a requirement for the reactor pressure vessel to be smaller even that of the 30 MWt HTTR, several challenging technical problems have to be dealt with to arrive in a high performance core design that provides extended fuel burnup, prolonged refueling period, improved fuel refueling scheme, improved fuel element and so on from the HTTR.
Fukaya, Yuji; Goto, Minoru; Ohashi, Hirofumi
Annals of Nuclear Energy, 138, p.107182_1 - 107182_9, 2020/04
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)The investigation on self-shielding effect of double heterogeneity for plutonium burner High Temperature Gas-cooled Reactor (HTGR) design has been performed. Plutonium burner HTGR designed in the previous study by using the advantage of double heterogeneity to control excess reactivity. In the present study, the mechanism of the self-shielding effect is elucidated by the analysis of burn-up calculation and reactivity decomposition based on exact perturbation theory. As a result, it is revealed that the characteristics of burn-up reactivity are determined by resonance cross section peak at 1 eV of 
Pu due to the surface term of background cross section, this is, the characteristics of neutron leakage from fuel lump and collision to a moderator. Moreover, significant spectrum shift is caused during the burn-up period, and it enhances reactivity worth of 
Pu and Pu in EOL.
Fukaya, Yuji; Goto, Minoru; Ohashi, Hirofumi; Yan, X.; Nishihara, Tetsuo; Tsubata, Yasuhiro; Matsumura, Tatsuro
Journal of Nuclear Science and Technology, 55(11), p.1275 - 1290, 2018/11
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)To reduce environmental burden and thread of nuclear proliferation, multi-recycling fuel cycle with High Temperature Gas-cooled Reactor (HTGR) has been investigated. Those problems are solved by incinerating TRans Uranium (TRU) nuclides, which is composed of plutonium and Minor Actinoide (MA), and there is concept to realize TRU incineration by multi-recycling with Fast Breeder Reactor (FBR). In this study, multi-recycling is realized even with thermal reactor by feeding fissile uranium from outside of the fuel cycle instead of breeding fissile nuclide. In this fuel cycle, recovered uranium by reprocessing and natural uranium are enriched and mixed with recovered TRU by reprocessing and partitioning to fabricate fresh fuels. The fuel cycle was designed for a Gas Turbine High Temperature Reactor (GTHTR300), whose thermal power is 600 MW, including conceptual design of uranium enrichment facility. Reprocessing is assumed as existing Plutonium Uranium Redox EXtraction (PUREX) with four-group partitioning technology. As a result, it was found that the TRU nuclides excluding neptunium can be recycled by the proposed cycle. The duration of potential toxicity decaying to natural uranium level can be reduced to approximately 300 years, and the footprint of repository for High Level Waste (HLW) can be reduced by 99.7% compared with GTHTR300 using existing reprocessing and disposal technology. Suppress plutonium is not generated from this cycle. Moreover, incineration of TRU from Light Water Reactor (LWR) cycle can be performed in this cycle.
Fukaya, Yuji; Mizuta, Naoki; Goto, Minoru; Ohashi, Hirofumi; Yan, X.
Proceedings of 9th International Topical Meeting on High Temperature Reactor Technology (HTR 2018) (USB Flash Drive), 7 Pages, 2018/10
Conceptual design study of a high performance commercial HTGR has been performed at target output of 165MWt. Requirements for the HTGR are small-sized vessel for transportation, durability of vessel to irradiation damage, fuel reloading scheme to shorten the duration of reloading, low pressure drop fuel element, a small number of fuel enrichments, and so on. To satisfy the requirement, we investigated the core configuration, shielding and reflector configuration, fuel reloading scheme. As a result, we completed the design with the vessel diameter of 4.5m, which can be transported by any means, such as, by load, rail, ship, and air plane, and high load factor over 90%.
Ohashi, Hirofumi; Goto, Minoru; Ueta, Shohei; Sato, Hiroyuki; Fukaya, Yuji; Kasahara, Seiji; Sasaki, Koei; Mizuta, Naoki; Yan, X.; Aoki, Takeshi*
Proceedings of 9th International Topical Meeting on High Temperature Reactor Technology (HTR 2018) (USB Flash Drive), 6 Pages, 2018/10
Conceptual design study of an experimental HTGR is performed to upgrade the plant system from Japanese High Temperature engineering Test Reactor (HTTR) to a commercial HTGR. Safety systems of HTTR are upgraded to demonstrate the commercial HTGR concept, such as a passive reactor cavity cooling system, a confinement, etc. An intermediate heat exchanger (IHX) is replaced by a steam generator (SG) for a process heat supply to demonstrate the technology for a commercial use. This paper describes the conceptual design study results of the plant system of the experimental HTGR.
Goto, Minoru; Fukaya, Yuji; Mizuta, Naoki; Inaba, Yoshitomo; Ohashi, Hirofumi; Yan, X.
Proceedings of 9th International Topical Meeting on High Temperature Reactor Technology (HTR 2018) (USB Flash Drive), 6 Pages, 2018/10
The HTTR (High Temperature engineering Test Reactor) constructed at JAEA-Oarai R&D center is a block-type experimental HTGR (High Temperature Gas-cooled Reactor) with 30 MW thermal power. It attained the first criticality at 1998 and has yielded very useful data for future HTGR design. Although the HTTR was designed very conservatively because the HTTR is the first HTGR for Japan, future HTGRs can be designed with a reasonable conservativeness based on the HTTR data. Additionally, it is possible to enhance the performance of the reactor core by improving the design and introducing new technologies. This paper describes a concept of an experimental HTGR that is upgraded from the HTTR by the reasonable conservativeness, the design improvement and the new technology introduction.
Nishihara, Tetsuo; Yan, X.; Tachibana, Yukio; Shibata, Taiju; Ohashi, Hirofumi; Kubo, Shinji; Inaba, Yoshitomo; Nakagawa, Shigeaki; Goto, Minoru; Ueta, Shohei; et al.
JAEA-Technology 2018-004, 182 Pages, 2018/07
JAEA-Technology-2018-004.pdf:18.14MB
Research and development on High Temperature Gas-cooled Reactor (HTGR) in Japan started since late 1960s. Japan Atomic Energy Agency (JAEA) in cooperation with Japanese industries has researched and developed system design, fuel, graphite, metallic material, reactor engineering, high temperature components, high temperature irradiation and post irradiation test of fuel and graphite, high temperature heat application and so on. Construction of the first Japanese HTGR, High Temperature engineering Test Reactor (HTTR), started in 1990. HTTR achieved first criticality in 1998. After that, various test operations have been carried out to establish the Japanese HTGR technologies and to verify the inherent safety features of HTGR. This report presents several system design of HTGR, the world-highest-level Japanese HTGR technologies, JAEA's knowledge obtained from construction, operation and management of HTTR and heat application technologies for HTGR.
Aihara, Jun; Ueta, Shohei; Goto, Minoru; Inaba, Yoshitomo; Shibata, Taiju; Ohashi, Hirofumi
JAEA-Technology 2018-002, 70 Pages, 2018/06
JAEA-Technology-2018-002.pdf:1.46MB
HTFP code is code for calculation of additional release amount of fission product (FP) from fuel rod in high temperature gas-cooled reactor (HTGR) after stop of fission. Minory changed Fornax-A code also can calculate that. Therefore, release behavior of Cs calculated with HTFP code was compared with that calculated with minory modified FORNAX-A code in this report. Release constants of Cs evaluated with minory modified FORNAX-A code are rather different from default values for HTFP code.
Fukaya, Yuji; Goto, Minoru; Ohashi, Hirofumi; Nishihara, Tetsuo; Tsubata, Yasuhiro; Matsumura, Tatsuro
Annals of Nuclear Energy, 116, p.224 - 234, 2018/06
Times Cited Count：2 Percentile：20.93(Nuclear Science & Technology)Optimization of disposal method and scenario to reduce volume of High Level Waste (HLW) and the footprint in a geological repository for High Temperature Gas-cooled Reactor (HTGR) has been performed. It was found that HTGR has great advantages to reducing HLW volume and its footprint, which are high burn-up, high thermal efficiency and pin-in-block type fuel, compared with those of LWR and has potential to reduce those more in the previous study. In this study, the scenario is optimized, and the geological repository layout is designed with the horizontal emplacement based on the KBS-3H concept instead of the vertical emplacement based on KBS-3V concept employed in the previous study. As a result, for direct disposal, the repository footprint can be reduced by 20 % by employing the horizontal without change of the scenario. By extending 40 years for cooling time before disposal, the footprint can be reduced by 50 %. For disposal with reprocessing, the number of canister generation can be reduced by 20 % by extending cooling time of 1.5 years between the discharge and reprocessing. The footprint per electricity generation can be reduced by 80 % by extending 40 years before disposal. Moreover, by employing four-group partitioning technology without transmutation, the footprint can be reduced by 90 % with cooling time of 150 years.
