Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Kondo, Yasuhiro; Hirano, Koichiro; Ito, Takashi; Kikuzawa, Nobuhiro; Kitamura, Ryo; Morishita, Takatoshi; Oguri, Hidetomo; Okoshi, Kiyonori; Shinozaki, Shinichi; Shinto, Katsuhiro; et al.
Journal of Physics; Conference Series, 1350, p.012077_1 - 012077_7, 2019/12
Times Cited Count：1 Percentile：48.14(Physics, Particles & Fields)We have upgraded a 3-MeV linac at J-PARC. The ion source is same as the J-PARC linac's, and the old 30-mA RFQ is replaced by a spare 50-mA RFQ, therefore, the beam energy is 3 MeV and the nominal beam current is 50 mA. The main purpose of this system is to test the spare RFQ, but also used for testing of various components required in order to keep the stable operation of the J-PARC accelerator. The accelerator has been already commissioned, and measurement programs have been started. In this paper, present status of this 3-MeV linac is presented.
Fuwa, Yasuhiro; Shinozaki, Shinichi; Chishiro, Etsuji; Hirane, Tatsuya; Fang, Z.*; Fukui, Yuji*; Futatsukawa, Kenta*; Mizobata, Satoshi*; Iwama, Yuhei*; Sato, Yoshikatsu*; et al.
Proceedings of 16th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.611 - 613, 2019/10
In the J-PARC linac, a proton accelerator is operated using 45 units of 324 MHz and 972 MHz klystrons. In the future stabilization and advancement of the accelerator, it is important to acquire the klystron output characteristics near the maximum output accurately. In order to understand this characteristics, measurement of the characteristics of the replaced klystron for some reason such as discharge, as well as the new klystron. However, such measurements have not been performed because of the risk of damage including peripheral equipment due to discharge and the temporal interference with the operation of the accelerator. Therefore, we set up a klystron test stand in the linac building and measured the high-voltage characteristics and input/output characteristics of the klystron under various operating parameters. By using this measurement result, the characteristics of klystron can be obtained before installation, and it becomes possible to determine the optimum operation parameters and make effective plan of klystron replacements. In addition, basic data for predicting the degradation tendency of klystron was acquired by comparing the characteristics of the used and used klystron.
Chadwick, M. B.*; Capote, R.*; Trkov, A.*; Herman, M. W.*; Brown, D. A.*; Hale, G. M.*; Kahler, A. C.*; Talou, P.*; Plompen, A. J.*; Schillebeeckx, P.*; et al.
Nuclear Data Sheets, 148, p.189 - 213, 2018/02
Times Cited Count：72 Percentile：97.99(Physics, Nuclear)The CIELO collaboration has studied neutron cross sections on nuclides that significantly impact criticality in nuclear facilities - 
U, 
U, 
Pu, 
Fe, 
O and 
H - with the aim of improving the accuracy of the data and resolving previous discrepancies in our understanding. This multi-laboratory pilot project, coordinated via the OECD/NEA Working Party on Evaluation Cooperation (WPEC) Subgroup 40 with support also from the IAEA, has motivated experimental and theoretical work and led to suites of new evaluated libraries that accurately reflect measured data and also perform well in integral simulations of criticality. This report summarizes our results and outlines plans for the next phase of this collaboration.
Chadwick, M. B.*; Capote, R.*; Trkov, A.*; Kahler, A. C.*; Herman, M. W.*; Brown, D. A.*; Hale, G. M.*; Pigni, M.*; Dunn, M.*; Leal, L.*; et al.
EPJ Web of Conferences, 146, p.02001_1 - 02001_9, 2017/09
Times Cited Count：6 Percentile：94.34(Nuclear Science & Technology)The CIELO collaboration has studied neutron cross sections on nuclides (O, Fe, 
U and Pu) that significantly impact criticality in nuclear technologies with the aim of improving the accuracy of the data and resolving previous discrepancies in our understanding. This multi-laboratory pilot project, coordinated via the OECD/NEA Working Party on Evaluation Cooperation (WPEC) Subgroup 40 with support also from the IAEA, has motivated experimental and theoretical work and led to suites of new evaluated libraries that accurately reflect measured data and also perform well in integral simulations of criticality.
Kondo, Yasuhiro; Asano, Hiroyuki*; Chishiro, Etsuji; Hirano, Koichiro; Ishiyama, Tatsuya; Ito, Takashi; Kawane, Yusuke; Kikuzawa, Nobuhiro; Meigo, Shinichiro; Miura, Akihiko; et al.
Proceedings of 28th International Linear Accelerator Conference (LINAC 2016) (Internet), p.298 - 300, 2017/05
We have constructed a linac for development of various accelerator components at J-PARC. The ion source is same as the J-PARC linac's, and the RFQ is a used one in the J-PARC linac. The beam energy is 3 MeV and nominal beam current is 30 mA. The accelerator has been already commissioned, and the first development program, laser-charge-exchange experiment for the transmutation experimental facility, has been started. In this paper, present status of this 3-MeV linac is presented.
Hori, Toshihiko*; Shinozaki, Shinichi; Sato, Yoshikatsu; Mizobata, Satoshi; Fukui, Yuji*; Futatsukawa, Kenta*
Proceedings of 13th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.429 - 432, 2016/11
The triode klystrons with a modulating anode have been used for the J-PARC linac. Recently, we exchanged four klystrons due to the frequent discharge at a modulating anode in the klystron tube. In order to understand the discharge mechanism and to estimate the time to replace the klystron, we need to monitor the long term performance of the klystron such as the degradation of a cathode emission current and the RF gain of the klystron tube and so on. Therefore, we started to develop the klystron perveance and gain monitor module (NIM Standard one). In this paper, we will present the design concept of the monitor module, and the first performance test result using the module prototype.
Hirano, Koichiro; Asano, Hiroyuki; Ishiyama, Tatsuya; Ito, Takashi; Okoshi, Kiyonori; Oguri, Hidetomo; Kondo, Yasuhiro; Kawane, Yusuke; Kikuzawa, Nobuhiro; Sato, Yoshikatsu; et al.
Proceedings of 13th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.310 - 313, 2016/11
We have used a beam scraper with the incident angle of 65deg to reduce the beam power deposition density in the MEBT between a 324 MHz RFQ and a 50-MeV DTL of the J-PARC linac. The 65
scraper was irradiated by the H
beam up to particle number of 1.47E22. We observed a lot of surface projections with several hundred micrometers high in the beam irradiation damage on the scraper by using the laser microscope. In order to study the limits of scrapers, we constructed a new 3 MeV linac at J-PARC. We will conduct the scraper irradiation test at the end of this year.
Kunieda, Satoshi; Shibata, Keiichi; Fukahori, Tokio; Kawano, Toshihiko*; Paris, M.*; Hale, G.*
JAEA-Conf 2015-003, p.33 - 38, 2016/03
We present recent progress of nuclear data evaluation method in the resolved resonance range. Our multi-channel R-matrix code now includes photon-channel and computational capability of charged-particle elastic scattering. We also present the physical constraint from the theory in the analysis of experimental data. Example analysis results are shown for 
Be and 
O compound system. Finally, perspectives are discussed toward the advancement of nuclear data in the resonance region including those for medium-heavy nuclei.
Futatsukawa, Kenta*; Kobayashi, Tetsuya*; Sato, Fumiaki; Shinozaki, Shinichi; Chishiro, Etsuji; Hirano, Koichiro; Fang, Z.*; Fukui, Yuji*; Hori, Toshihiko; Michizono, Shinichiro*
Proceedings of 12th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1317 - 1320, 2015/09
In the J-PARC linac, an RF deflector installed in 3-MeV Medium Energy Beam Transport (MEBT1) is used to kick the unnecessary beam and the intermediate-pulse like a comb is created. The kicked beam leads to a scraper downstream the RF deflector and lose all kinetic energy. When the beam current increases to 50 mA of the design value, the heat load of a scraper to irradiate the kicked beam increases and its surface is predicted to be damaged. Therefore, we are preparing the tandem scrapers to reduce the damage. The half of the kicked beam leads to a scraper and the residual is to the other. The chopping operation is achieved by rotating the phase of the RF deflector in the periodic cycles by the LLRF system. We will introduce the phase rotation system and the test results.
Hori, Toshihiko; Shinozaki, Shinichi; Sato, Fumiaki; Fukui, Yuji*; Futatsukawa, Kenta*
Proceedings of 12th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.643 - 646, 2015/09
We are making efforts to decrease the fault rate of the high voltage power supplies for 324 MHz klystron. A new Veto module has been developed to prevent the 25 Hz trigger fan out module from malfunction due to the klystron discharge. As the result of installing the Veto module to the SDTL#16 klystron station, the klystron had never stopped for two months operation although the discharge occurred forty-two times during the operation. It confirmed that the installation of the Veto module is extremely useful to operate the klystron stably.
O through R-matrix analysisKunieda, Satoshi; Kawano, Toshihiko*; Paris, M.*; Hale, G. M.*; Shibata, Keiichi; Fukahori, Tokio
Nuclear Data Sheets, 123, p.159 - 164, 2015/01
Times Cited Count：7 Percentile：45.00(Physics, Nuclear)The collision matrix in the R-matrix theory is unitary, hence theory brings strong constraints to behavior of the parameters. An unitarity-imposed R-matrix analysis is carried out for O system to evaluate O neutron cross-sections in the resolved resonance range. Covariance matrices are also estimated both for the cross-sections and angular distributions with a deterministic method. Present results mirror the nature in the theory as well as experimental information.
Kondo, Yasuhiro; Morishita, Takatoshi; Yamazaki, Saishun; Hori, Toshihiko; Sawabe, Yuki; Chishiro, Etsuji; Fukuda, Shimpei; Hasegawa, Kazuo; Hirano, Koichiro; Kikuzawa, Nobuhiro; et al.
Physical Review Special Topics; Accelerators and Beams, 17(12), p.120101_1 - 120101_8, 2014/12
Times Cited Count：6 Percentile：41.82(Physics, Nuclear)We performed a beam test of a new radio frequency quadrupole linac (RFQ III) for the beam current upgrade of the Japan Proton Accelerator Research Complex. First, the conditioning of RFQ III was conducted, and after 20 h of conditioning, RFQ III became very stable with a nominal peak power and duty factor of 400 kW and 1.5%, respectively. An off-line beam test was subsequently conducted before installation in the accelerator tunnel. The transmission, transverse emittance, and energy spread of the 50-mA negative hydrogen beam from RFQ III were measured and compared with simulation results. The experiment and simulation results showed good agreement; therefore, we conclude that the performance of RFQ III conforms to its design.
Kondo, Yasuhiro; Morishita, Takatoshi; Yamazaki, Saishun; Hori, Toshihiko; Sawabe, Yuki; Takagi, Akira*
Proceedings of 27th International Linear Accelerator Conference (LINAC 2014) (Internet), p.267 - 269, 2014/12
We performed a beam test of a new 324-MHz 3-MeV H RFQ (RFQ III) for the beam-current upgrade of the J-PARC linac. RFQ III is the first RFQ developed to meet the requirement of the J-PARC linac. The peak beam current is 50 mA, pulse length is 500 micro-sec, and the repetition is 25 Hz. Prior to the installation to the accelerator tunnel in summer of 2014, we constructed a test stand for off line testing of the new ion source and RFQ. Basic performances of RFQ III such as transmission and emittances were measured. In this paper, the beam test results are presented.
Arita, Ren*; Nakazato, Tomoharu*; Shimizu, Toshihiko*; Yamanoi, Kohei*; Empizo, M.*; Hori, Tatsuhiro*; Fukuda, Kazuhito*; Minami, Yuki*; Sarukura, Nobuhiko*; Maruyama, Momoko; et al.
Optical Materials, 36(12), p.2012 - 2015, 2014/10
Times Cited Count：10 Percentile：47.73(Materials Science, Multidisciplinary)A single shot image of a ZnO crystal excited by the EUV laser of Kansai Photon Science Institute was captured. The evaluated EUV beam waist radii from the ZnO emission pattern along the horizontal and vertical axes are 5.0 and 4.7
m, respectively. The expected focal spot size of EUV laser and the spatial resolution of the magnifier (including the Schwarzschild objectives and lenses) are however 1 and 4m, respectively. The discrepancy on the spatial resolutions is attributed to exciton diffusion. We estimated the ZnO exciton diffusion length from the effective decay time which is shortened by exciton-exciton collision quenching and which is dependence on excitation energy density. Our results indicate that the short lifetime of ZnO is required to improve the spatial resolution.
Oguri, Hidetomo; Hasegawa, Kazuo; Ito, Takashi; Chishiro, Etsuji; Hirano, Koichiro; Morishita, Takatoshi; Shinozaki, Shinichi; Ao, Hiroyuki; Okoshi, Kiyonori; Kondo, Yasuhiro; et al.
Proceedings of 11th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.389 - 393, 2014/10
no abstracts in English
O up to 5.2 MeV through R-matrix analysisKunieda, Satoshi; Kawano, Toshihiko*; Paris, M.*; Hale, G. M.*; Shibata, Keiichi; Fukahori, Tokio
NEA/NSC/DOC(2014)13 (Internet), p.33 - 39, 2014/07
There still remain differences among measured data, which makes the evaluated cross-sections uncertain, and which consequently affects some integral calculation. O is one of the important nuclei in the nuclear application, but such kinds of issues appears in elastic-scattering and (n,
) reaction cross-sections. Purpose of this study is to solve those issues as they are common concerns in the world. We present estimated cross sections and their covariance data which are "physically" constrained by the R-matrix theory. The differences between the estimated and the measured cross-sections will be also discussed.
Futatsukawa, Kenta*; Ikegami, Masanori*; Ito, Yuichi; Kikuzawa, Nobuhiro; Sato, Fumiaki; Shinozaki, Shinichi; Suzuki, Takahiro*; Chishiro, Etsuji; Hirano, Koichiro; Fang, Z.*; et al.
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1149 - 1153, 2014/06
no abstracts in English
Hori, Toshihiko; Sato, Fumiaki; Shinozaki, Shinichi; Chishiro, Etsuji; Oguri, Hidetomo; Futatsukawa, Kenta*; Fukui, Yuji*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1001 - 1003, 2014/06
no abstracts in English
Kawamura, Masato*; Chishiro, Etsuji; Hori, Toshihiko; Shinozaki, Shinichi; Sato, Fumiaki; Fukui, Yuji*; Futatsukawa, Kenta*; Yamazaki, Masayoshi*; Sagawa, Ryu*; Miyajima, Noriyuki*; et al.
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.605 - 607, 2014/06
This report describes the present status of the klystron power supply systems for the J-PARC linac. The systems for the 181 MeV linac were operated from September to May. A few breakdowns were occurred, and are described in this report. The new systems for the upgrade of the linac from 181MeV to 400 MeV have been installed until now, and the 3 HVDCPSs and the 3 anode modulators of the new systems have been operated. All the systems for 400 MeV linac will be operated in this autumn.
H, O, Fe, U, and PuChadwick, M. B.*; Dupont, E.*; Bauge, E.*; Blokhin, A.*; Bouland, O.*; Brown, D. A.*; Capote, R.*; Carlson, A. D.*; Danon, Y.*; De Saint Jean, C.*; et al.
Nuclear Data Sheets, 118, p.1 - 25, 2014/04
Times Cited Count：108 Percentile：98.39(Physics, Nuclear)CIELO (Collaborative International Evaluated Library Organization) provides a new working paradigm to facilitate evaluated nuclear reaction data advances. It brings together experts from across the international nuclear reaction data community to identify and document discrepancies among existing evaluated data libraries, measured data, and model calculation interpretations, and aims to make progress in reconciling these discrepancies to create more accurate ENDF-formatted files. The focus will initially be on a small number of the highest-priority isotopes, namely H, O, Fe, U, and Pu. This paper identifies discrepancies between various evaluations of the highest priority isotopes. The evaluated data for these materials in the existing nuclear data libraries are reviewed, and some integral properties are given. The paper summarizes a program of nuclear science and computational work needed to create the new CIELO nuclear data evaluations.
