Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Kondo, Yasuhiro; Hirano, Koichiro; Ito, Takashi; Kikuzawa, Nobuhiro; Kitamura, Ryo; Morishita, Takatoshi; Oguri, Hidetomo; Okoshi, Kiyonori; Shinozaki, Shinichi; Shinto, Katsuhiro; et al.
Journal of Physics; Conference Series, 1350, p.012077_1 - 012077_7, 2019/12
Times Cited Count：1 Percentile：52.28(Physics, Particles & Fields)We have upgraded a 3-MeV linac at J-PARC. The ion source is same as the J-PARC linac's, and the old 30-mA RFQ is replaced by a spare 50-mA RFQ, therefore, the beam energy is 3 MeV and the nominal beam current is 50 mA. The main purpose of this system is to test the spare RFQ, but also used for testing of various components required in order to keep the stable operation of the J-PARC accelerator. The accelerator has been already commissioned, and measurement programs have been started. In this paper, present status of this 3-MeV linac is presented.
Kondo, Yasuhiro; Asano, Hiroyuki*; Chishiro, Etsuji; Hirano, Koichiro; Ishiyama, Tatsuya; Ito, Takashi; Kawane, Yusuke; Kikuzawa, Nobuhiro; Meigo, Shinichiro; Miura, Akihiko; et al.
Proceedings of 28th International Linear Accelerator Conference (LINAC 2016) (Internet), p.298 - 300, 2017/05
We have constructed a linac for development of various accelerator components at J-PARC. The ion source is same as the J-PARC linac's, and the RFQ is a used one in the J-PARC linac. The beam energy is 3 MeV and nominal beam current is 30 mA. The accelerator has been already commissioned, and the first development program, laser-charge-exchange experiment for the transmutation experimental facility, has been started. In this paper, present status of this 3-MeV linac is presented.
Sueyoshi, Tetsuro*; Nishimura, Takahiro*; Fujiyoshi, Takanori*; Mitsugi, Fumiaki*; Ikegami, Tomoaki*; Ishikawa, Norito
Superconductor Science and Technology, 29(10), p.105006_1 - 105006_7, 2016/10
Times Cited Count：8 Percentile：37.83(Physics, Applied)A systematic investigation of flux pinning by widely direction-dispersed columnar defects (CDs) in YBa
Cu
Oy thin films was carried out by using heavy-ion irradiation: a parallel configuration of CDs aligned along the 
-axis, and two trimodal splay configurations composed of crossing CDs; relative to the -axis, where the splay plane defined by the three irradiation angles is perpendicular (trimodal-A) or parallel (trimodal-B) to the transport current direction. The trimodal configurations show high pinning efficiency over a wide range of magnetic field orientations compared to the parallel one at low magnetic field. In particular, trimodal-B shows the higher critical current density of the two trimodal configurations.
Miura, Akihiko; Maruta, Tomofumi*; Liu, Y.*; Miyao, Tomoaki*; Kawane, Yusuke; Ouchi, Nobuo; Oguri, Hidetomo; Ikegami, Masanori*; Hasegawa, Kazuo
JPS Conference Proceedings (Internet), 8, p.011002_1 - 011002_6, 2015/09
In the J-PARC Linac, an energy upgrade project has started since 2009 using Annular-ring Coupled Structure cavities to achieve design beam power of 1 MW at the exit of the downstream rapid cycling synchrotron. Linac beam parameters of the upgraded Linac is drastically improved especially for the beam energy from 181 to 400 MeV in the project. To meet with the significant upgrades of the Linac, beam monitors to be used for the upgraded beam line are newly designed and fabricated as well as the beam monitor layout is designed with the consideration to the beam commissioning strategies. This paper introduces the beam monitor layout in the new beam line and the commissioning results to confirm the beam monitor functioning.
Miura, Akihiko; Feschenko, A. V.*; Mirzojan, A. N.*; Miyao, Tomoaki*; Ouchi, Nobuo; Maruta, Tomofumi*; Liu, Y.*; Oguri, Hidetomo; Ikegami, Masanori*; Hasegawa, Kazuo
JPS Conference Proceedings (Internet), 8, p.011003_1 - 011003_6, 2015/09
In J-PARC Linac, an energy upgrade project has started since 2009 using Annular-ring Coupled Structure (ACS) cavities. We have decided to use the bunch shape monitors (BSM) as the monitors of the longitudinal beam width measurement in order to take the longitudinal matching using two bunchers located in the upstream of ACS cavities, where the RF frequency jumps from 324 to 972 MHz. Three BSMs were completely fabricated and installed in the beam line. The BSMs were commissioned with the beam and their operability was demonstrated. We found the vacuum degradation during the measurement. We once removed all BSMs to have a vacuum conditioning and postponed the longitudinal matching at the establishment of 400-MeV operation of the energy upgraded Linac. In this paper, we introduce the mechanism of the BSM, its operability, the measurement results with the 181 MeV beam and consistency check with the respect cavity amplitude. We also describe the operational vacuum conditions and the outline of the improvement of the vacuum system for the BSMs.
Maruta, Tomofumi*; Liu, Y.*; Futatsukawa, Kenta*; Miyao, Tomoaki*; Miura, Akihiko; Ikegami, Masanori*
Proceedings of 12th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.432 - 436, 2015/09
no abstracts in English
Miura, Akihiko; Ouchi, Nobuo; Oguri, Hidetomo; Hasegawa, Kazuo; Miyao, Tomoaki*; Ikegami, Masanori*
Journal of the Korean Physical Society, 66(3), p.364 - 372, 2015/02
Times Cited Count：2 Percentile：20.46(Physics, Multidisciplinary)In J-PARC Linac, an energy upgrade project has started to achieve the design beam power of 1 MW at the exit of downstream synchrotron. To meet with significant upgrades of the beam parameters, beam monitors used for the beam commissioning are modified and fabricated. We discuss how to design and assemble the beam monitors for the upgraded Linac. We delivered them for the new upgraded beam line periodically and newly fabricated monitors for the longitudinal matching are also delivered because of the frequency jump between original RF cavity and newly developed cavity. Finally we suppose the commissioning plans to support the monitor check.
Kondo, Yasuhiro; Morishita, Takatoshi; Yamazaki, Saishun; Hori, Toshihiko; Sawabe, Yuki; Chishiro, Etsuji; Fukuda, Shimpei; Hasegawa, Kazuo; Hirano, Koichiro; Kikuzawa, Nobuhiro; et al.
Physical Review Special Topics; Accelerators and Beams, 17(12), p.120101_1 - 120101_8, 2014/12
Times Cited Count：6 Percentile：42.9(Physics, Nuclear)We performed a beam test of a new radio frequency quadrupole linac (RFQ III) for the beam current upgrade of the Japan Proton Accelerator Research Complex. First, the conditioning of RFQ III was conducted, and after 20 h of conditioning, RFQ III became very stable with a nominal peak power and duty factor of 400 kW and 1.5%, respectively. An off-line beam test was subsequently conducted before installation in the accelerator tunnel. The transmission, transverse emittance, and energy spread of the 50-mA negative hydrogen beam from RFQ III were measured and compared with simulation results. The experiment and simulation results showed good agreement; therefore, we conclude that the performance of RFQ III conforms to its design.
Miura, Akihiko; Ouchi, Nobuo; Oguri, Hidetomo; Hasegawa, Kazuo; Maruta, Tomofumi*; Liu, Y.*; Miyao, Tomoaki*; Ikegami, Masanori*
Proceedings of 27th International Linear Accelerator Conference (LINAC 2014) (Internet), p.1059 - 1061, 2014/12
An energy upgrade project has started in the J-PARC Linac since 2009. In the upgraded project, beam energy in the Linac has increased from original 181 MeV to 400 MeV using the additional 21 Annular-ring Coupled Structure Linac (ACS) cavities. The new beam monitors as the beam current monitors, the phase monitors, the beam position monitors and the transverse profile monitors (wire scanner monitors) were designed and fabricated. By the end of November, 2013, all beam monitors were completely installed. From the middle of December, we started the beam commissioning to achieve the beam energy as 400 MeV, as well as to confirm the beam monitor functioning. We achieved the 400 MeV beam acceleration at the middle of January, 2014 using newly installed beam monitors. This paper describes the beam monitor installation and the beam commissioning results of beam monitor functioning.
Oguri, Hidetomo; Hasegawa, Kazuo; Ito, Takashi; Chishiro, Etsuji; Hirano, Koichiro; Morishita, Takatoshi; Shinozaki, Shinichi; Ao, Hiroyuki; Okoshi, Kiyonori; Kondo, Yasuhiro; et al.
Proceedings of 11th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.389 - 393, 2014/10
no abstracts in English
Hirano, Koichiro; Ito, Takashi; Kondo, Yasuhiro; Shinozaki, Shinichi; Chishiro, Etsuji; Miura, Akihiko; Morishita, Takatoshi; Ikegami, Masanori*; Kubota, Chikashi*; Sugimura, Takashi*; et al.
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.858 - 861, 2014/06
Two RF-deflecting cavities as a chopper and a beam scraper have been used in the MEBT between a 324 MHz RFQ and a 50-MeV DTL of the J-PARC Linac. We plan to increase a peak beam current up to 50 mA by replacing an ion source and a RFQ after the summer shutdown in 2014. Beam loss occurs in the RF chopper for the 50 mA operation. Moreover, the beam scraper cannot fully stand the beam load with 50 mA, 0.5 ms, 3 MeV, and 25 Hz. We have studied the new RF chopper cavity by using HFSS code and the tandem scraper system with two scrapers.
Miura, Akihiko; Feschenko, A. V.*; Mirzojan, A. N.*; Miyao, Tomoaki*; Ouchi, Nobuo; Oguri, Hidetomo; Hasegawa, Kazuo; Ikegami, Masanori*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.705 - 708, 2014/06
In J-PARC linac, a project for energy and intensity upgrade has been progressed since 2009 using Annular-ring Coupled Structure (ACS) cavities. Because the longitudinal matching of the injection beam to the ACS cavities is required as well as the transverse matching, we decided to employ the bunch shape monitors (BSM's) to measure the longitudinal beam profile. We developed three BSM's in collaboration with INR (Institute for Nuclear Research: Russia) for the upstream part of the ACS section. We introduce the structure of BSM and mention the measured results taken during the commissioning of BSM.
Futatsukawa, Kenta*; Ikegami, Masanori*; Ito, Yuichi; Kikuzawa, Nobuhiro; Sato, Fumiaki; Shinozaki, Shinichi; Suzuki, Takahiro*; Chishiro, Etsuji; Hirano, Koichiro; Fang, Z.*; et al.
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1149 - 1153, 2014/06
no abstracts in English
-values in BaZrO/YBaCuO
quasi-multilayered films with columnar defectsSueyoshi, Tetsuro*; Kotaki, Tetsuya*; Fujiyoshi, Takanori*; Mitsugi, Fumiaki*; Ikegami, Tomoaki*; Ishikawa, Norito
Physica C, 494, p.153 - 157, 2013/11
Times Cited Count：5 Percentile：25.2(Physics, Applied)BaZrO/YBaCuOy quasi-multilayered films, in which the size and the spatial distribution of BaZrO nano-particles were controlled, were irradiated using 200 MeV Xe ions along the c-axis direction. Whenthe BaZrO nano-particles were larger in size, the flux lines not captured by CDs, such as interstitial fluxlines between CDs and double kinks of flux lines, can be pinned more effectively by the BaZrO nano-particles, so that the Jc enhances for high magnetic fields and high temperature. In addition, the inverse correlation between Jc and n-value appears at high temperature in increasing magnetic field for the film with correlated rows of the nano-particles which might be curved off the c-axis. These suggest that the hybrid flux pinning depends not only on the combination of one-dimensional (1D) and three-dimensional pinning centers (3D-PCs) but also on the size and the spatial distribution of the 3D-PCs.
Maruta, Tomofumi; Miura, Akihiko; Sako, Hiroyuki; Tamura, Jun; Ikegami, Masanori*; Futatsukawa, Kenta*; Fang, Z.*; Miyao, Tomoaki*; Liu, Y.*
Journal of the Korean Physical Society, 63(7), p.1274 - 1279, 2013/10
Times Cited Count：0 Percentile：0(Physics, Multidisciplinary)Miura, Akihiko; Miyao, Tomoaki*; Ito, Takashi; Hirano, Koichiro; Nammo, Kesao*; Maruta, Tomofumi; Tamura, Jun; Ikegami, Masanori*; Naito, Fujio*
Proceedings of 9th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.653 - 655, 2013/08
The beam operation of J-PARC linac was suspended until December 2011 due to the damage by the Tohoku earthquake in March 2011. After resumed the operations, we measured the residual radiation along with the beam line during a short interval. Because the higher residual radiation was detected at the surface of drift tube linac (DTL) cavity by radiation survey, we installed the scintillation beam loss monitors (BLM) at the points where the higher radiation was detected to understand the cause of the radiation. Even the DTL section is low energy part of the linac, fine structure of the beam loss was observed by the scintillation BLM. And we measured the beam loss occurred at the DTL with the parameters of beam orbit and cavity settings. Also, the BLM is employed for the linac tuning. In this paper, the result of the radiation measurement and beam loss signals obtained by the scintillation BLMs are presented.
Ikegami, Masanori*; Fang, Z.*; Futatsukawa, Kenta*; Miyao, Tomoaki*; Liu, Y.*; Maruta, Tomofumi; Sako, Hiroyuki; Miura, Akihiko; Tamura, Jun; Wei, G.
Proceedings of 9th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.64 - 67, 2013/08
Sueyoshi, Tetsuro*; Furuki, Yuichi*; Tanaka, Eiki*; Fujiyoshi, Takanori*; Mitsugi, Fumiaki*; Ikegami, Tomoaki*; Ishikawa, Norito
IEEE Transactions on Applied Superconductivity, 23(3), p.8002404_1 - 8002404_4, 2013/06
Times Cited Count：8 Percentile：42.19(Engineering, Electrical & Electronic)To investigate whether one dimensional pinning centers (1D PCs) can attain the isotropic critical current density (
) properties, columnar defects (CDs) crossing at widespread angles were installed by heavy-ion irradiations into YBCO thin films. For the sample containing the CDs crossing relative to the -axis, the plateau-like behavior of 
is realized over a wide range of magnetic field orientations, except for around B 
-plane where a dip structure is accompanied by a rapid decline of the . For the bimodal splay configuration consisting of CDs crossing relative to the -axis, a single peak around the -axis is observed in the angular dependence of , suggesting the splay effect at B -axis by the crossed CDs. Two parallel families of CDs crossing relative to the -plane, on the other hand, bring about not a peak but a dip around B -plane on the angular dependence of .
Ikegami, Masanori*; Fang, Z.*; Futatsukawa, Kenta*; Miyao, Tomoaki*; Maruta, Tomofumi; Sako, Hiroyuki; Miura, Akihiko; Wei, G.; Tamura, Jun
Proceedings of 3rd International Particle Accelerator Conference (IPAC '12) (Internet), p.3293 - 3295, 2012/05
no abstracts in English
Miura, Akihiko; Hasegawa, Kazuo; Oguri, Hidetomo; Ouchi, Nobuo; Igarashi, Zenei*; Miyao, Tomoaki*; Ikegami, Masanori*
Proceedings of 2nd International Particle Accelerator Conference (IPAC 2011) (Internet), p.2328 - 2330, 2011/09
On March 11, 2011, the great earthquake occurred off the Pacific coast of Tohoku. This earthquake and related ones caused the big damage of the J-PARC accelerators. As for the beam monitors in J-PARC linac, some commissioning tools had damage and the vacuum leakage was observed. In the recovery work, we inspected the damage and put the emergency steps for the vacuum equipment. In this paper, detailed inspection results of beam monitors are described and also the recovery work is introduced.
