Orientation dependence of yield strength in a new single crystal-like FeCrAl oxide dispersion strengthened alloy

Aghamiri, S. M. S.*; Sugawara, Naoya*; Ukai, Shigeharu; Ono, Naoko*; Sakamoto, Kan*; Yamashita, Shinichiro

Materials Characterization, 176, p.111043_1 - 111043_6, 2021/06

https://doi.org/10.1016/j.matchar.2021.111043

Advanced oxidation-resistant FeCrAl ODS alloys were developed via the control of composition-processing conditions for the accident tolerant fuel (ATF) cladding. For the first time, a single-crystal like recrystallized FeCrAl ODS alloy was achieved with a unique crystallographic texture of 110-plane and 211-direction and a high number density of fine nanoscale oxide particles. Evaluation of yield strengths at different temperatures showed higher values in transverse (T) direction than longitudinal (L) direction. The crystal orientation dependence of the yield strength up to 800C was attributed to lower value of Schmid factor in transverse direction. Accordingly, the critical resolved shear stress of this practical class of advanced materials was calculated in various temperatures.

Microstructure and texture evolution and ring-tensile properties of recrystallized FeCrAl ODS cladding tubes

Aghamiri, S. M. S.*; Sowa, Takashi*; Ukai, Shigeharu*; Ono, Naoko*; Sakamoto, Kan*; Yamashita, Shinichiro

Materials Science & Engineering A, 771, p.138636_1 - 138636_12, 2020/01

https://doi.org/10.1016/j.msea.2019.138636

Oxide dispersion strengthened (ODS) FeCrAl ferritic steels are being developed as potential accident tolerance fuel cladding materials for the light water reactors (LWRs) due to significant improvement in steam oxidation by alumina forming scale and good mechanical properties up to high temperatures. In this study, the microstructural characteristics and tensile properties of the two FeCrAl ODS cladding tubes with different extrusion temperatures of 1100C and 1150C were investigated during processing conditions. While the hot extruded sample showed micron sized elongated grains with strong -fiber in 110 texture, cold pilger rolling process change the microstructure to submicron/micron size grain structure along with texture evolution to both -fiber (110 texture) and -fiber ({111} texture) via crystalline rotations. Subsequently, final annealing resulted in evolution of microstructure to large grain recrystallized structure starting at recrystallization temperature of 810-850C. Two distinct texture development happened in recrystallized cladding tubes, i.e., only large elongated grains of (110) 211 texture following extrusion temperature of 1100C; and two texture components of (110) 211 and {111} 112 following higher extrusion temperature of 1150C. The different texture development and retarding of recrystallization progress in 1100C-extruded cladding tubes were attributed to higher distribution of oxide particles.

Cutting operation of simulated fuel assembly heating examination by AWJ

Abe, Yuta; Nakagiri, Toshio; Watatani, Satoshi*; Maruyama, Shinichiro*

JAEA-Technology 2017-023, 46 Pages, 2017/10

JAEA-Technology-2017-023.pdf:8.01MB

This is a report on Abrasive Water Jet (AWJ) cutting work carried out on specimen, which was used for Simulated Fuel Assembly Heating Examination by Collaborative Laboratories for Advanced Decommissioning Science (CLADS) molten core behavior analysis group in February 2016. The simulated fuel assembly is composed of Zirconia for the outer crucible/simulated fuel, stainless steel for the control blade and Zircaloy (Zr) for the cladding tube/channel box. Therefore, it is necessary to cut at once substances having a wide range of fracture toughness and hardness. Moreover, it is a large specimen with an approximate size of 300 mm. In addition, epoxy resin has high stickiness, making it more difficult to cut. Considering these effects, AWJ cutting was selected. The following two points were devised, and this specimen could be cut with AWJ. If it was not possible to cut at one time like a molten portion of boride, it was repeatedly cut. By using Abrasive Suspension Jet (ASJ) system with higher cutting ability than Abrasive Injection Jet (AIJ, conventional method) system, cutting time was shortened. As a result of this work, the cutting method in Simulated Fuel Assembly Heating Examination was established. Incidentally, in the cutting operation, when the cutting ability was lost at the tip of the AWJ, a curved cut surface, which occurs when the jet flowed away from the feeding direction, could be confirmed at the center of the test body. From the next work, to improve the cutting efficiency, we propose adding a mechanism such as turning the cutting member itself for re-cutting from the exit side of the jet and appropriate traverse speed to protect cut surface.

The Possible interplanetary transfer of microbes; Assessing the viability of spp. under the ISS environmental conditions for performing exposure experiments of microbes in the Tanpopo mission

Kawaguchi, Yuko*; Yang, Y.*; Kawashiri, Narutoshi*; Shiraishi, Keisuke*; Takasu, Masako*; Narumi, Issey*; Sato, Katsuya; Hashimoto, Hirofumi*; Nakagawa, Kazumichi*; Tanigawa, Yoshiaki*; et al.

Origins of Life and Evolution of Biospheres, 43(4-5), p.411 - 428, 2013/10

https://doi.org/10.1007/s11084-013-9346-1

Tolerance of anhydrobiotic eggs of the tardigrade to extreme environments

Horikawa, Daiki*; Yamaguchi, Ayami*; Sakashita, Tetsuya; Tanaka, Daisuke*; Hamada, Nobuyuki*; Yukuhiro, Fumiko*; Kuwahara, Hirokazu*; Kunieda, Takekazu*; Watanabe, Masahiko*; Nakahara, Yuichi*; et al.

Astrobiology, 12(4), p.283 - 289, 2012/04

https://doi.org/10.1089/ast.2011.0669

We examined the hatchability of hydrated and anhydrobiotic eggs of the tardigrade to hatch after ionizing irradiation (helium ions), extremely low and high temperatures, and high vacuum. Anhydrobiotic eggs (50% lethal dose; 1690 Gy) were substantially more radioresistant than hydrated ones (50% lethal dose; 509 Gy). Anhydrobiotic eggs also have a broader temperature resistance compared with hydrated ones. Over 70% of the anhydrobiotic eggs treated at high and low temperatures, but all of the hydrated eggs failed to hatch. After exposure to high vacuum conditions, the hatchability of the anhydrobiotic eggs was comparable to that of untreated control eggs.

Recent progress in the energy recovery linac project in Japan

Sakanaka, Shogo*; Akemoto, Mitsuo*; Aoto, Tomohiro*; Arakawa, Dai*; Asaoka, Seiji*; Enomoto, Atsushi*; Fukuda, Shigeki*; Furukawa, Kazuro*; Furuya, Takaaki*; Haga, Kaiichi*; et al.

Proceedings of 1st International Particle Accelerator Conference (IPAC '10) (Internet), p.2338 - 2340, 2010/05

http://accelconf.web.cern.ch/AccelConf/IPAC10/papers/tupe091.pdf

Future synchrotron light source using a 5-GeV energy recovery linac (ERL) is under proposal by our Japanese collaboration team, and we are conducting R&D efforts for that. We are developing high-brightness DC photocathode guns, two types of cryomodules for both injector and main superconducting (SC) linacs, and 1.3 GHz high CW-power RF sources. We are also constructing the Compact ERL (cERL) for demonstrating the recirculation of low-emittance, high-current beams using above-mentioned critical technologies.

Studies on engineering technologies in the Mizunami Underground Research Laboratory (FY 2007) (Contract research)

Noda, Masaru*; Suyama, Yasuhiro*; Nobuto, Jun*; Ijiri, Yuji*; Mikake, Shinichiro; Matsui, Hiroya

JAEA-Technology 2009-009, 194 Pages, 2009/07

JAEA-Technology-2009-009.pdf:44.14MB

In construction phase in MIU, the study on engineering technology consist of following four subjects, which are Demonstration of design methodology of a greatly deepr underground structure, Demonstration of excavation and supplymentary methods of a greatly deepr underground structure, Demonstration of the countermeasure during excavation of a greatly deepr underground structure and Demonstration of the safe construction for a greatly deepr underground structure. In the study in FY2007, the design methodlogy in Phase 1 is verified until 200 m depth on excavation of ventilation shaft. A plan, countermeasure and concept for influence of differential water pressure, long-term maintenance and risk management in the view of geological disposal project were proposed.

Measurement of the spin and magnetic moment of Al

Ozawa, Akira*; Matsuta, Kensaku*; Nagatomo, Takashi*; Mihara, Mototsugu*; Yamada, Kazunari*; Yamaguchi, Takayuki*; Otsubo, Takashi*; Momota, Sadao*; Izumikawa, Takuji*; Sumikama, Toshiyuki*; et al.

Physical Review C, 74(2), p.021301_1 - 021301_4, 2006/08

https://doi.org/10.1103/PhysRevC.74.021301

no abstracts in English

Measurements of neutron spectra produced from a thick iron target bombarded with 1.5-GeV protons

Meigo, Shinichiro; Shigyo, Nobuhiro*; Iga, Kiminori*; Iwamoto, Yosuke*; Kitsuki, Hirohiko*; Ishibashi, Kenji*; Maehata, Keisuke*; Arima, Hidehiko*; Nakamoto, Tatsushi*; Numajiri, Masaharu*

AIP Conference Proceedings 769, p.1513 - 1516, 2005/05

https://doi.org/10.1063/1.1945292

For validation of calculation codes that are employed in the design of accelerator facilities, spectra of neutrons produced from a thick iron target bombarded with 1.5-GeV protons were measured. The calculated results with NMTC/JAM were compared with the present experimental results. It is found the NMTC/JAM generally shows in good agreement with experiment. Furthermore, the calculation gives good agreement with the experiment for the energy region 20 to 80 MeV, whereas the NMTC/JAM gives 50 % of the experimental data for the heavy nuclide target such as lead and tungsten target.

Current status of the AGS spallation target experiment

Nakashima, Hiroshi; Takada, Hiroshi; Kasugai, Yoshimi; Meigo, Shinichiro; Maekawa, Fujio; Kai, Tetsuya; Konno, Chikara; Ikeda, Yujiro; Oyama, Yukio; Watanabe, Noboru; et al.

Proceedings of 6th Meeting of the Task Force on Shielding Aspects of Accelerators, Targets and Irradiation Facilities (SATIF-6), (OECD/NEA No.3828), p.27 - 36, 2004/00

no abstracts in English