Martensitic transformation-governed Luders deformation enables large ductility and late-stage strain hardening in ultrafine-grained austenitic stainless steel at low temperatures

Mao, W.*; Gao, S.*; Gong, W.; Kawasaki, Takuro; Ito, Tatsuya; Harjo, S.; Tsuji, Nobuhiro*

Acta Materialia, 278, p.120233_1 - 120233_13, 2024/10

https://doi.org/10.1016/j.actamat.2024.120233

neutron diffraction revealing the achievement of excellent combination of strength and ductility in metastable austenitic steel by grain refinement

Mao, W.; Gong, W.; Harjo, S.; Morooka, Satoshi; Gao, S.*; Kawasaki, Takuro; Tsuji, Nobuhiro*

Journal of Materials Science & Technology, 176, p.69 - 82, 2024/03

https://doi.org/10.1016/j.jmst.2023.07.036

The yield stress of Fe-24Ni-0.3C (wt.%) metastable austenitic steel increased 3.5 times (158 551 MPa) when the average grain size decreased from 35 m (coarse-grained [CG]) to 0.5 m (ultrafine-grained [UFG]), whereas the tensile elongation was kept large (0.87 0.82). neutron diffraction measurements of the CG and UFG Fe-24Ni-0.3C steels were performed during tensile deformation at room temperature to quantitatively elucidate the influence of grain size on the mechanical properties and deformation mechanisms. The initial stages of plastic deformation in the CG and UFG samples were dominated by dislocation slip, with deformation-induced martensitic transformation (DIMT) also occurring in the later stage of deformation. Results show that grain refinement increases the initiation stress of DIMT largely and suppresses the rate of DIMT concerning the strain, which is attributed to the following effects. (i) Grain refinement increased the stabilization of austenite and considerably delayed the initiation of DIMT in the 111//LD (LD: loading direction) austenite grains, which were the most stable grains for DIMT. As a result, most of the 111//LD austenite grains in the UFG specimens failed to transform into martensite. (ii) Grain refinement also suppressed the autocatalytic effect of the martensitic transformation. Nevertheless, the DIMT with the low transformation rate in the UFG specimen was more efficient in increasing the flow stress and more appropriate to maintain uniform deformation than that in the CG specimen during deformation. The above phenomena mutually contributed to the excellent combination of strength and ductility of the UFG metastable austenitic steel.

Quantitatively evaluating the huge Lders band deformation in an ultrafine grain stainless steel by combining neutron diffraction and digital image correlation analysis

Mao, W.; Gao, S.*; Gong, W.; Harjo, S.; Kawasaki, Takuro; Tsuji, Nobuhiro*

Scripta Materialia, 235, p.115642_1 - 115642_6, 2023/10

https://doi.org/10.1016/j.scriptamat.2023.115642

In the present study, a hybrid neutron diffraction and digital image correlation measurement was performed on tensile deformation of an ultrafine grain (UFG) stainless steel exhibiting a huge Lders band deformation to evaluate the individual contribution of the austenite matrix and the deformation-induced martensite to the strain hardening during the propagation of the band. Quantitative analysis revealed that the strain hardening of the austenite matrix was insufficient to maintain a uniform deformation when the flow stress was greatly enhanced by the UFG structure. The strain hardening required for the Lders band to propagate was mostly provided by the formation of martensite and the high internal stress within it.

Compressive deformation behavior of AZ31 alloy at 21K; An neutron diffraction study

Gong, W.; Kawasaki, Takuro; Zheng, R.*; Mayama, Tsuyoshi*; Sun, B.*; Aizawa, Kazuya; Harjo, S.; Tsuji, Nobuhiro*

Scripta Materialia, 225, p.115161_1 - 115161_5, 2023/03

https://doi.org/10.1016/j.scriptamat.2022.115161

observation of twinning and detwinning in AZ31 alloy

Gong, W.; Zheng, R.*; Harjo, S.; Kawasaki, Takuro; Aizawa, Kazuya; Tsuji, Nobuhiro*

Journal of Magnesium and Alloys (Internet), 10(12), p.3418 - 3432, 2022/12

https://doi.org/10.1016/j.jma.2022.02.002

Achieving excellent mechanical properties in type 316 stainless steel by tailoring grain size in homogeneously recovered or recrystallized nanostructures

Liu, M.*; Gong, W.; Zheng, R.*; Li, J.*; Zhang, Z.*; Gao, S.*; Ma, C.*; Tsuji, Nobuhiro*

Acta Materialia, 226, p.117629_1 - 117629_13, 2022/03

https://doi.org/10.1016/j.actamat.2022.117629

Catalog of gamma-ray glows during four winter seasons in Japan

Wada, Yuki*; Matsumoto, Takahiro*; Enoto, Teruaki*; Nakazawa, Kazuhiro*; Yuasa, Takayuki*; Furuta, Yoshihiro*; Yonetoku, Daisuke*; Sawano, Tatsuya*; Okada, Go*; Nanto, Hidehito*; et al.

Physical Review Research (Internet), 3(4), p.043117_1 - 043117_31, 2021/12

https://doi.org/10.1103/PhysRevResearch.3.043117

Performance of in situ gamma-ray spectrometry in the assessment of radioactive cesium deposition around the Fukushima Daiichi Nuclear Power Plant

Ji, Y.-Y.*; Ochi, Kotaro; Hong, S. B.*; Nakama, Shigeo; Sanada, Yukihisa; Mikami, Satoshi

Radiation Physics and Chemistry, 179, p.109205_1 - 109205_11, 2021/02

https://doi.org/10.1016/j.radphyschem.2020.109205

In situ gamma-ray spectrometry using diverse survey platforms has been conducted in contaminated areas with several dose rate levels around the Fukushima Daiichi Nuclear Power Plant (FDNPP). Six survey sites, including two evacuation zones around the FDNPP, were selected for ground-based gamma-ray spectrometry using HPGe (high purity Ge) and LaBr(Ce) detectors to assess the radioactive cesium deposition in the ground. The diverse levels of radioactivity of Cs were then distributed to six survey sites from 30 to 3000 kBq m in the measurement period of October 2018. A method to directly calculate the depth profile using in situ measurement was introduced so as to have representation over a wide area, and the results were successfully compared with those of sample analysis at one point in the site.

Nature of the Dirac gap modulation and surface magnetic interaction in axion antiferromagnetic topological insulator MnBiTe

Shikin, A. M.*; Estyunin, D. A.*; Klimovskikh, I. I.*; Filnov, S. O.*; Kumar, S.*; Schwier, E. F.*; Miyamoto, Koji*; Okuda, Taichi*; Kimura, Akio*; Kuroda, Kenta*; et al.

Scientific Reports (Internet), 10, p.13226_1 - 13226_13, 2020/08

https://doi.org/10.1038/s41598-020-70089-9

Study of quasielastic barrier distributions as a step towards the synthesis of superheavy elements with hot fusion reactions

Tanaka, Taiki*; Morita, Kosuke*; Morimoto, Koji*; Kaji, Daiya*; Haba, Hiromitsu*; Boll, R. A.*; Brewer, N. T.*; Van Cleve, S.*; Dean, D. J.*; Ishizawa, Satoshi*; et al.

Physical Review Letters, 124(5), p.052502_1 - 052502_6, 2020/02

https://doi.org/10.1103/PhysRevLett.124.052502