Antiferromagnetic order and crystalline electric field in noncentrosymmetric hexagonal RuAs ( = Sm and Yb)

Hirose, Yusuke; Tsukui, Hiroki*; Kato, Yuta*; Shono, Rina*; Honda, Fuminori*; Aoki, Dai*; Settai, Rikio*

Physical Review Materials (Internet), 10(8), p.084407_1 - 084407_8, 2026/08

https://doi.org/10.1103/nr4t-wypp

Horonobe Underground Research Laboratory Project Investigation report for the 2024 fiscal year

Nakayama, Masashi; Ishii, Eiichi; Aoyagi, Kazuhei; Hayano, Akira; Murakami, Hiroaki; Ono, Hirokazu; Takeda, Masaki; Fukatsu, Yuta; Mochizuki, Akihito; Ozaki, Yusuke; et al.

JAEA-Review 2025-042, 136 Pages, 2025/12

JAEA-Review-2025-042.pdf:12.95MB

The Horonobe Underground Research Laboratory (URL) Project is being pursued by the Japan Atomic Energy Agency (JAEA) to enhance the reliability of relevant technologies for geological disposal of high-level radioactive waste through investigating the deep geological environment within the host sedimentary rocks at Horonobe-cho in Hokkaido, north Japan. In the fiscal year 2024, we continued R&D on "Study on near-field system performance in geological environment", "Demonstration of repository design options", and "Understanding of buffering behaviour of sedimentary rock to natural perturbations". These are identified as key R&D on challenges to be tackled in the Horonobe underground research plan for the fiscal year 2020 onwards. Specifically, "full-scale engineered barrier system (EBS) performance experiment" and "solute transport experiment with model testing" were carried out as part of "Study on near-field system performance in geological environment". "Demonstration of engineering feasibility of repository technology" and "evaluation of EBS behaviour over 100C" were addressed for "Demonstration of repository design options". The validation of a method for assessing permeability using the Ductility Index and a method for estimating the state of in-situ ground pressure from hydraulic perturbation tests were investigated as part of the study "Understanding of buffering behaviour of sedimentary rock to natural perturbations". In FY2024, we continued construction of the East Access Shaft and the Ventilation Shaft, and construction of these shafts were completed to a depth of 500 m. After the completion of the East Access Shaft, excavation of the West Access Shaft and 500 m gallery has began. As of the end of FY2024, excavation progress is as follows, the East Access Shaft and the Ventilation Shaft were 500 m depth, the West Access Shaft was 472 m depth, 500 m gallery was 112.9 m, respectively. In the Horonobe International Project (HIP), Management Board and Joint Task Meeting was held at the Horonobe URL in June 2024 to review the progress of construction of galleries and preparations of experiments. Task Meetings to review the implementation plan for in-situ testing and analysis were also held. HIP will be implemented in two phases: Phase 1 (from FY2022 to FY2024) and Phase 2 (from FY2025 to FY2028), the research results of Phase 1 were compiled in FY2024.

Dissolution behavior of calcium uranate under oxidizing and reducing conditions

Kato, Yuto*; Sasaki, Takayuki*; Tonna, Ryutaro*; Kobayashi, Taishi*; Okamoto, Yoshihiro

Applied Geochemistry, 175, p.106196_1 - 106196_9, 2024/11

https://doi.org/10.1016/j.apgeochem.2024.106196

Present status of JAEA-Tokai tandem accelerator facility

Matsui, Yutaka; Nakamura, Masahiko; Kutsukake, Kenichi; Kabumoto, Hiroshi; Asozu, Takuhiro; Otokawa, Yoshinori; Ikekame, Takuma; Nakagawa, Sohei; Kato, Yuta; Ishizaki, Nobuhiro; et al.

Dai-36-Kai Tandemu Kasokuki Oyobi Sono Shuhen Gijutsu No Kenkyukai Hokokushu, p.17 - 21, 2024/06

no abstracts in English

Sintering and microstructural behaviors of mechanically blended Nd/Sm-doped MOX

Hirooka, Shun; Horii, Yuta; Sunaoshi, Takeo*; Uno, Hiroki*; Yamada, Tadahisa*; Vauchy, R.; Hayashizaki, Kohei; Nakamichi, Shinya; Murakami, Tatsutoshi; Kato, Masato

Journal of Nuclear Science and Technology, 60(11), p.1313 - 1323, 2023/11

https://doi.org/10.1080/00223131.2023.2192725

Additive MOX pellets are fabricated by a conventional dry powder metallurgy method. NdO and SmO are chosen as the additive materials to simulate the corresponding soluble fission products dispersed in MOX. Shrinkage curves of the MOX pellets are obtained by dilatometry, which reveal that the sintering temperature is shifted toward a value higher than that of the respective regular MOX. The additives, however, promote grain growth and densification, which can be explained by the effect of oxidized uranium cations covering to a pentavalent state. Ceramography reveals large agglomerates after sintering, and Electron Probe Micro-Analysis confirms that inhomogeneous elemental distribution, whereas XRD reveals a single face-centered cubic phase. Finally, by grinding and re-sintering the specimens, the cation distribution homogeneity is significantly improved, which can simulate spent nuclear fuels with soluble fission products.

Investigation of physical properties of glove for glove-box and estimation of its life-time

Kobayashi, Daisuke; Yamamoto, Masahiko; Nishida, Naoki; Miyoshi, Ryuta; Nemoto, Ryo*; Hayashi, Hiroyuki*; Kato, Keisuke; Nishino, Saki; Kuno, Takehiko; Kitao, Takahiko; et al.

Nihon Hozen Gakkai Dai-18-Kai Gakujutsu Koenkai Yoshishu, p.237 - 240, 2022/07

All gloves attached to glove-box in Tokai Reprocessing Plant have a fixed expiration date and have to be replaced every 4-year. However, degrees of glove deterioration are different depending on its usage environment (frequency, chemicals, radiation, etc.), because of rubber products. Therefore, physical properties such as tensile strength, elongation, hardness of gloves are measured, and the life-time of gloves are estimated. As a result, gloves without any defects in its appearance have enough physical property for acceptance criteria of new glove. The extrapolated physical property of glove is sufficiently larger than the reported values of damaged glove. No deterioration in physical properties of gloves, that are periodically replaced without any defects in its appearance, is observed and the usable life-time of the glove is estimated to be 8 years.

Material data acquisition activities to develop the material strength standard for sodium-cooled fast reactors

Toyota, Kodai; Onizawa, Takashi; Wakai, Takashi; Hashidate, Ryuta; Kato, Shoichi

Proceedings of International Conference on Fast Reactors and Related Fuel Cycles; Sustainable Clean Energy for the Future (FR22) (Internet), 10 Pages, 2022/04

Evaluation of tensile and creep properties on 9Cr-ODS steel claddings

Yano, Yasuhide; Hashidate, Ryuta; Tanno, Takashi; Imagawa, Yuya; Kato, Shoichi; Onizawa, Takashi; Ito, Chikara; Uwaba, Tomoyuki; Otsuka, Satoshi; Kaito, Takeji

JAEA-Data/Code 2021-015, 64 Pages, 2022/01

JAEA-Data-Code-2021-015.pdf:2.6MB
JAEA-Data-Code-2021-015(errata).pdf:0.14MB

From a view point of practical application of fast breeder reactor cycles, which takes advantage of safety and economic efficiency and makes a contribution of volume reduction and mitigation of degree of harmfulness of high-level radioactive waste, it is necessary to develop fuel cladding materials for fast reactors (FRs) in order to achieve high-burnup. Oxide dispersion strengthened (ODS) steel have been studied for use as potential fuel cladding materials in FRs owing to their excellent resistance to swelling and their high-temperature strength in Japan Atomic Energy Agency. It is very important to establish the materials strength standard in order to apply ODS steels as a fuel cladding. Therefore, it is necessary to acquire the mechanical properties such as tensile, creep rupture strength tests and so on. In this study, tensile and creep rupture strengths of 9Cr-ODS steel claddings were evaluated using by acquired these data. Because of the phase transformation temperature of 9Cr-ODS steel, temperature range for the evaluation was divided into two ones at AC1 transformation temperature of 850C.

Proposal of simulation material test technique for clarifying the structure failure mechanisms under excessive seismic loads

Hashidate, Ryuta; Kato, Shoichi; Onizawa, Takashi; Wakai, Takashi; Kasahara, Naoto*

Proceedings of ASME 2021 Pressure Vessels and Piping Conference (PVP 2021) (Internet), 9 Pages, 2021/07

It is very essential to clarify the structure failure mechanisms under excessive seismic loads. However, structural tests using actual structural materials are very difficult and expensive. Therefore, we have proposed the structure test approach using lead alloys in order to simulate the structure failure mechanisms under the excessive seismic loads. In this study, we conducted material tests using lead alloy and verified the effectiveness of the simulated material tests. Moreover, we formulated inelastic constitutive equations (best fit fatigue curve equation and cyclic stress range - strain range relationship equation) of lead alloy based on the results of a series of material tests. Nonlinear numerical analyses, e.g. finite element analyses, can be performed using the proposed equations. A series of simulation material test technique enables structural tests and analyses using lead alloy to simulate the structure failure phenomena under excessive seismic loads.

Proposal of simulation materials test technique and their constitutive equations for structural tests and analyses simulating severe accident conditions

Hashidate, Ryuta; Kato, Shoichi; Onizawa, Takashi; Wakai, Takashi; Kasahara, Naoto*

Proceedings of ASME 2020 Pressure Vessels and Piping Conference (PVP 2020) (Internet), 9 Pages, 2020/08

https://doi.org/10.1115/PVP2020-21397

Although it is very essential to clarify how the structure collapses under the severe accident conditions, the failure mechanisms in excessive high temperatures are not clarified. However, it is very difficult and expensive to perform structural tests using actual structural materials. Therefore, we propose to use lead alloys instead of actual structural materials. For demonstration of analogy between the failure mechanisms of lead alloys structure at low temperature and those of the actual structures at high temperature, numerical analyses are required. Although the authors proposed inelastic constitutive equations for numerical analyses in 2019, the equations could not successfully express because of large variations observed in the material tests of the lead alloy. In this study, we propose the improved inelastic constitutive equations of the lead alloy on the basis of the material test results used by aged alloy which can stabilized the material characteristic.