Development of a design optimization framework for sodium-cooled fast reactors, 2; Development of optimization analysis control function

Doda, Norihiro; Nakamine, Yoshiaki*; Kuwagaki, Kazuki; Hamase, Erina; Kikuchi, Norihiro; Yoshimura, Kazuo; Matsushita, Kentaro; Tanaka, Masaaki

Keisan Kogaku Koenkai Rombunshu (CD-ROM), 28, 5 Pages, 2023/05

As a part of the development of the "Advanced Reactor Knowledge- and AI-aided Design Integration Approach through the whole plant lifecycle (ARKADIA)" to automatically optimize the life cycle of innovative nuclear reactors including fast reactors, ARKADIA-design is being developed to support the optimization of fast reactor in the conceptual design stage. ARKADIA-Design consists of three systems (Virtual plant Life System (VLS), Evaluation assistance and Application System (EAS), and Knowledge Management System (KMS)). A design optimization framework controls the connection between the three systems through the interfaces in each system. This paper reports on the development of an optimization analysis control function that performs design optimization analysis combining plant behavior analysis by VLS and optimization study by EAS.

Thermally altered subsurface material of asteroid (162173) Ryugu

Kitazato, Kohei*; Milliken, R. E.*; Iwata, Takahiro*; Abe, Masanao*; Otake, Makiko*; Matsuura, Shuji*; Takagi, Yasuhiko*; Nakamura, Tomoki*; Hiroi, Takahiro*; Matsuoka, Moe*; et al.

Nature Astronomy (Internet), 5(3), p.246 - 250, 2021/03

https://doi.org/10.1038/s41550-020-01271-2

Here we report observations of Ryugu's subsurface material by the Near-Infrared Spectrometer (NIRS3) on the Hayabusa2 spacecraft. Reflectance spectra of excavated material exhibit a hydroxyl (OH) absorption feature that is slightly stronger and peak-shifted compared with that observed for the surface, indicating that space weathering and/or radiative heating have caused subtle spectral changes in the uppermost surface. However, the strength and shape of the OH feature still suggests that the subsurface material experienced heating above 300 C, similar to the surface. In contrast, thermophysical modeling indicates that radiative heating does not increase the temperature above 200 C at the estimated excavation depth of 1 m, even if the semimajor axis is reduced to 0.344 au. This supports the hypothesis that primary thermal alteration occurred due to radiogenic and/or impact heating on Ryugu's parent body.

Comparative study on the thermal behavior of structural concretes of sodium-cooled fast reactor

Kikuchi, Shin; Koga, Nobuyoshi*; Yamazaki, Atsushi*

Journal of Thermal Analysis and Calorimetry, 137(4), p.1211 - 1224, 2019/08

https://doi.org/10.1007/s10973-019-08045-7

In this study, two siliceous concretes with similar specification as structural concretes of SFR were selected for the comparative study of the thermal behavior. The thermal behavior of the structural concretes was investigated in a temperature range from room temperature to 1900 K using TG-differential thermal analysis (DTA) and other supplementary techniques. The softening and melting of the concretes initiated in the thermal decomposition product of the cement portion in the temperature range 1400-1600 K. Because the compositional difference between the cement portion of two different siliceous concretes was characterized by different Ca(OH)/CaCO ratios, the melting temperature ranges of those thermal decomposition products are not so significantly different. On the other hand, the melting of the aggregate is directly influenced by the initial composition of SiO compounds.

Investigation of hydrogen gas generation by radiolysis for cement-solidified products of used adsorbents for water decontamination

Sato, Junya; Kikuchi, Hiroshi*; Kato, Jun; Sakakibara, Tetsuro; Matsushima, Ryotatsu; Sato, Fuminori; Kojima, Junji; Nakazawa, Osamu

QST-M-8; QST Takasaki Annual Report 2016, P. 62, 2018/03

https://repo.qst.go.jp/records/73811

no abstracts in English

Operation and commissioning of IFMIF (International Fusion Materials Irradiation Facility) LIPAc injector

Okumura, Yoshikazu; Gobin, R.*; Knaster, J.*; Heidinger, R.*; Ayala, J.-M.*; Bolzon, B.*; Cara, P.*; Chauvin, N.*; Chel, S.*; Gex, D.*; et al.

Review of Scientific Instruments, 87(2), p.02A739_1 - 02A739_3, 2016/02

https://doi.org/10.1063/1.4936248

IFMIF is an accelerator based neutron facility having two set of linear accelerators each producing 125mA/CW deuterium ion beams (250mA in total) at 40MeV. The LIPAc (Linear IFMIF Prototype Accelerator) being developed in the IFMIF-EVEDA project consists of an injector, a RFQ accelerator, and a part of superconducting Linac, whose target is to demonstrate 125mA/CW deuterium ion beam acceleration up to 9MeV. The injector has been developed in CEA Saclay and already demonstrated 140mA/100keV deuterium beam. The injector was disassembled and delivered to the International Fusion Energy Research Center (IFERC) in Rokkasho, Japan, and the commissioning has started after its reassembly 2014; the first beam production has been achieved in November 2014. Up to now, 100keV/120mA/CW hydrogen ion beam has been produced with a low beam emittance of 0.2 .mm.mrad (rms, normalized).

Progress of the high current Prototype Accelerator for IFMIF/EVEDA

Okumura, Yoshikazu; Ayala, J.-M.*; Bolzon, B.*; Cara, P.*; Chauvin, N.*; Chel, S.*; Gex, D.*; Gobin, R.*; Harrault, F.*; Heidinger, R.*; et al.

Proceedings of 12th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.203 - 205, 2015/09

http://www.pasj.jp/web_publish/pasj2015/proceedings/PDF/FROL/FROL08.pdf

Under the framework of Broader Approach (BA) agreement between Japan and Euratom, IFMIF/EVEDA project was launched in 2007 to validate the key technologies to realize IFMIF. The most crucial technology to realize IFMIF is two set of linear accelerator each producing 125mA/CW deuterium ion beams up to 40MeV. The prototype accelerator, whose target is 125mA/CW deuterium ion beam acceleration up to 9MeV, is being developed in International Fusion Research Energy Center (IFERC) in Rokkasho, Japan. The injector developed in CEA Saclay was delivered in Rokkasho in 2014, and is under commissioning. Up to now, 100keV/120mA/CW hydrogen ion beams and 100keV/90mA/CW duty deuterium ion beams are successfully produced with a low beam emittance of 0.21 .mm.mrad (rms, normalized). Delivery of RFQ components will start in 2015, followed by the installation of RF power supplies in 2015.

Status quo of the injector for the IFMIF/EVEDA prototype accelerator

Shinto, Katsuhiro; Ichikawa, Masahiro; Takahashi, Yasuyuki*; Kubo, Takashi*; Tsutsumi, Kazuyoshi; Kikuchi, Takayuki; Kasugai, Atsushi; Sugimoto, Masayoshi; Gobin, R.*; Girardot, P.*; et al.

Proceedings of 11th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1009 - 1012, 2014/10

http://www.pasj.jp/web_publish/pasj2014/proceedings/PDF/SUP0/SUP025.pdf

The prototype accelerator is being developed as an engineering validation for the International Fusion Materials Irradiation Facility (IFMIF) equipped with an accelerator-driven-type neutron source for developing fusion reactor materials. This prototype accelerator is a deuteron linear accelerator consisting of an injector, an RFQ, a superconducting linac and their auxiliaries. It aims to produce a CW D beam with the energy and current of 9 MeV/125 mA. The injector test was completed at CEA/Saclay in 2012 for producing a CW H beam and a CW D beam with the energy and current of 100 keV/140 mA. After the beam test at CEA/Saclay, the injector was transported to the International Fusion Energy Research Centre (IFERC) located in Rokkasho, Aomori, Japan. In the end of 2013, installation of the injector was started at IFERC for the injector beam test beginning from summer 2014 in order to obtain better beam qualities to be satisfied with the injection and acceleration of the following accelerators. In this paper, some results of the injector beam test performed at CEA/Saclay and the status quo of the installation of the injector at IFERC are presented.

Sulfate complexation of element 104, Rf, in HSO/HNO mixed solution

Li, Z.*; Toyoshima, Atsushi; Asai, Masato; Tsukada, Kazuaki; Sato, Tetsuya; Sato, Nozomi; Kikuchi, Takahiro; Nagame, Yuichiro; Schdel, M.; Pershina, V.*; et al.

Radiochimica Acta, 100(3), p.157 - 164, 2012/03

https://doi.org/10.1524/ract.2012.1898

Fundamental welding R&D results for manufacturing vacuum vessel of JT-60SA

Asano, Shiro*; Okuyama, Toshihisa*; Onawa, Toshio*; Yanagi, Yutaka*; Ejiri, Mitsuru*; Kanahara, Toshio*; Ichihashi, Koji*; Kikuchi, Atsushi*; Mizumaki, Shoichi*; Masaki, Kei; et al.

Fusion Engineering and Design, 86(9-11), p.1816 - 1820, 2011/10

https://doi.org/10.1016/j.fusengdes.2011.03.024

The real vacuum vessel (VV) manufacturing of JT-60SA has started since Nov. 2009 at Toshiba. Prior to starting manufacturing, fundamental welding R&Ds had been performed by three stages. In the first stage, primary tests for screening welding method were performed. In the second stage, the trial welding for 1m-long straight and curved double shell samples were conducted. The dependences of welding quality and distortion on the welding conditions, such as arc voltage and current, setting accuracy, welding sequence, the shape of grooves, etc. were measured. In addition, welding condition with low heat input was explored. In the last stage, fabrication sequence was confirmed and established by the trial manufacturing of the 20 upper half mock-up. This poster presents the R&D results obtained in the first and second stages.

Achievement of 500 keV negative ion beam acceleration on JT-60U negative-ion-based neutral beam injector

Kojima, Atsushi; Hanada, Masaya; Tanaka, Yutaka*; Kawai, Mikito*; Akino, Noboru; Kazawa, Minoru; Komata, Masao; Mogaki, Kazuhiko; Usui, Katsutomi; Sasaki, Shunichi; et al.

Nuclear Fusion, 51(8), p.083049_1 - 083049_8, 2011/08

https://doi.org/10.1088/0029-5515/51/8/083049

Hydrogen negative ion beams of 490 keV, 3 A and 510 keV, 1 A have been successfully produced in the JT-60 negative ion source with three acceleration stages. These successful productions of the high-energy beams at high current have been achieved by overcoming the most critical issue, i.e., a poor voltage holding of the large negative ion sources with the grids of 2 m for JT-60SA and ITER. To improve voltage holding capability, the breakdown voltages for the large grids was examined for the first time. It was found that a vacuum insulation distance for the large grids was 6-7 times longer than that for the small-area grid (0.02 m). From this result, the gap lengths between the grids were tuned in the JT-60 negative ion source. The modification of the ion source also realized a significant stabilization of voltage holding and a short conditioning time. These results suggest a practical use of the large negative ion sources in JT-60SA and ITER.