Matsuoka, Amane; Yasumune, Takashi; Kojima, Nobuhiro; Miyauchi, Hideaki; Takasaki, Koji; Hashimoto, Makoto
JAEA-Review 2021-055, 11 Pages, 2021/12
The dose limit for the eye lens was lowered on April 1 2021, and a 3 mm dose equivalent was added to the calculation. The guidelines require that lens dosimeters be worn and managed when there is a risk of exceeding control standards. In this report, in order to examine future management methods, we investigated whether work that might exceed the equivalent dose limit was performed in the past. As a result of the investigation, the exposure dose for all works after fiscal year 2008 was sufficiently low compared to the equivalent dose limit. For this reason, it is considered that there is no need for additional management of wearing a personal dosimeter near the eyes for the work that is normally performed. In the future, as in the past, the basic management method will be to wear a dosimeter only on the basic part of the trunk under uniform exposure conditions, and to wear a dosimeter on the basic part of the trunk and the maximum dose part under nonuniform exposure conditions. When performing work with a high exposure dose to the eye lens, a dosimeter should be worn near the eye to measure the 3 mm dose equivalent.
Yamaura, Junichi*; Hiraka, Haruhiro*; Iimura, Soshi*; Muraba, Yoshinori*; Bang, J.*; Ikeuchi, Kazuhiko*; Nakamura, Mitsutaka; Inamura, Yasuhiro; Honda, Takashi*; Hiraishi, Masatoshi*; et al.
Physical Review B, 99(22), p.220505_1 - 220505_6, 2019/06
Inelastic neutron scattering was performed for an iron-based superconductor, where most of D (deuterium) replaces oxygen, while a tiny amount goes into interstitial sites. By first-principle calculation, we characterize the interstitial sites for D (and for H slightly mixed) with four equivalent potential minima. Below the superconducting transition temperature Tc = 26 K, new excitations emerge in the range 5-15 meV, while they are absent in the reference system LaFeAsOF. The strong excitations at 14.5 meV and 11.1 meV broaden rapidly around 15 K and 20 K, respectively, where each energy becomes comparable to twice of the superconducting gap. The strong excitations are ascribed to a quantum rattling, or a band motion of hydrogen, which arises only if the number of potential minima is larger than two.
Kitao, Takahiko; Takeuchi, Yoshikatsu; Kimura, Takashi; Kojima, Junji; Shioya, Satoshi; Tasaki, Takashi; Nakamura, Hironobu
Nihon Kaku Busshitsu Kanri Gakkai Dai-38-Kai Nenji Taikai Rombunshu (Internet), 9 Pages, 2018/04
In order to ensure and strengthen nuclear security measures, an active cultivation of nuclear security culture implemented by both entire organization and individual persons is vitally essential. Tokai reprocessing facility has conducted various activities such as case study education and training, yearly posters and patrolling the site by upper-level management that all employees hold a deep rooted belief that there is a credible insider and outsider threat, and that nuclear security is important. These activities are conducted in order to establish the foundation of beliefs and attitudes of effective nuclear security culture based on the IAEA guideline. This report introduces our activities fostering nuclear security culture in Tokai reprocessing facility that the evaluation and the continuous improvement of bidirectional activities by both top-down from multiple management levels and bottom-up from individual employee, and our challenges need to be worked on for the future.
Nakajima, Kenji; Kawakita, Yukinobu; Ito, Shinichi*; Abe, Jun*; Aizawa, Kazuya; Aoki, Hiroyuki; Endo, Hitoshi*; Fujita, Masaki*; Funakoshi, Kenichi*; Gong, W.*; et al.
Quantum Beam Science (Internet), 1(3), p.9_1 - 9_59, 2017/12
The neutron instruments suite, installed at the spallation neutron source of the Materials and Life Science Experimental Facility (MLF) at the Japan Proton Accelerator Research Complex (J-PARC), is reviewed. MLF has 23 neutron beam ports and 21 instruments are in operation for user programs or are under commissioning. A unique and challenging instrumental suite in MLF has been realized via combination of a high-performance neutron source, optimized for neutron scattering, and unique instruments using cutting-edge technologies. All instruments are/will serve in world-leading investigations in a broad range of fields, from fundamental physics to industrial applications. In this review, overviews, characteristic features, and typical applications of the individual instruments are mentioned.
Ueno, Yasuhiro*; Aoki, Masaharu*; Fukao, Yoshinori*; Higashi, Yoshitaka*; Higuchi, Takashi*; Iinuma, Hiromi*; Ikedo, Yutaka*; Ishida, Keiichi*; Ito, Takashi; Iwasaki, Masahiko*; et al.
Hyperfine Interactions, 238(1), p.14_1 - 14_6, 2017/11
Hata, Kuniki; Inoue, Hiroyuki*; Kojima, Takao*; Kasahara, Shigeki; Hanawa, Satoshi; Ueno, Fumiyoshi; Tsukada, Takashi; Iwase, Akihiro*
Proceedings of Symposium on Water Chemistry and Corrosion in Nuclear Power Plants in Asia 2017 (AWC 2017) (USB Flash Drive), p.304 - 314, 2017/09
A model simulation of radiolysis of mixed solutions of NaCl and NaBr was carried out. The simulation result agreed well with the experimental result, and Br played an important role in determining the amounts of products from water radiolysis. The simulation result also showed that, in highly pure NaCl solutions, the steady-state concentration of a radolytic product, HO, was mainly controlled by three reactions (Cl + OH ClOH, ClOH Cl + OH, and ClOH + H Cl + HO), which indicated that accurate evaluation of the rate constants of these reactions was very important in improving the radiolysis simulation of solutions containing Cl. An immersion test using a low-alloy steel, SQV2A, in the mixed solutions was also carried out under irradiation. The corrosion rate increased or decreased depending on the pH or the concentrations of the halide ions in a similar way to the change in concentration of HO produced from water radiolysis, which is affected by the presence of Cl and Br. However, at high pH values (12), the corrosion rate was almost zero even though the concentration of HO was high. This could be attributed to enhancement of the passivity of test specimens at higher pH values.
Saito, Kyoichi*; Kojima, Takashi*; Asai, Shiho
Bunseki Kagaku, 66(4), p.233 - 242, 2017/04
Insoluble cobalt ferrocyanide and sodium titanate specifically capture cesium and strontium ions, respectively, in water contaminated with radionuclides which is found in Fukushima Daiichi NPP. The inorganic compounds used in this study were formed as precipitates in the polymer chain grafted onto a commercially available 6-nylon fiber using radiation-induced graft polymerization. An impregnation structure with the precipitates entangled by the grafted polymer chain through an electrostatic interaction via multipoints was indicated. The resultant insoluble cobalt ferrocyanide- or sodium titanate-impregnated fiber exhibited a higher adsorption rate and adsorption capacity per gram of the inorganic compound for cesium or strontium ions in seawater than conventional granular adsorbents.
Strasser, P.*; Aoki, Masaharu*; Fukao, Yoshinori*; Higashi, Yoshitaka*; Higuchi, Takashi*; Iinuma, Hiromi*; Ikedo, Yutaka*; Ishida, Keiichi*; Ito, Takashi; Iwasaki, Masahiko*; et al.
Hyperfine Interactions, 237(1), p.124_1 - 124_9, 2016/12
Kojima, Saori*; Uchibori, Akihiro; Takata, Takashi; Ohno, Shuji; Fukuda, Takeshi*; Yamaguchi, Akira*
Proceedings of 10th Japan-Korea Symposium on Nuclear Thermal Hydraulics and Safety (NTHAS-10) (USB Flash Drive), 8 Pages, 2016/11
Analytical evaluation on a self-wastage phenomenon at heat transfer tubes in the steam generator of sodium cooled fast reactors has been performed by using the sodium-water reaction analysis code SERAPHIM. In this study, a fluid-structure thermal coupling model was developed and incorporated in the SERAPHIM code to evaluate heat transfer between the sodium-side reacting flow and the outer surface of the heat transfer tube. The effect of the fluid-structure thermal coupling model on the temperature field was demonstrated through the numerical analyses.
Hata, Kuniki; Inoue, Hiroyuki*; Kojima, Takao*; Iwase, Akihiro*; Kasahara, Shigeki; Hanawa, Satoshi; Ueno, Fumiyoshi; Tsukada, Takashi
Nuclear Technology, 193(3), p.434 - 443, 2016/03
Yoshida, Masafumi; Hanada, Masaya; Kojima, Atsushi; Kashiwagi, Mieko; Grisham, L. R.*; Hatayama, Akiyoshi*; Shibata, Takanori*; Yamamoto, Takashi*; Akino, Noboru; Endo, Yasuei; et al.
Fusion Engineering and Design, 96-97, p.616 - 619, 2015/10
In JT-60 Super Advanced for the fusion experiment, 22A, 100s negative ions are designed to be extracted from the world largest ion extraction area of 450 mm 1100 mm. One of the key issues for producing such as high current beams is to improve non-uniform production of the negative ions. In order to improve the uniformity of the negative ions, a tent-shaped magnetic filter has newly been developed and tested for JT-60SA negative ion source. The original tent-shaped filter significantly improved the logitudunal uniformity of the extracted H ion beams. The logitudinal uniform areas within a 10 deviation of the beam intensity were improved from 45% to 70% of the ion extraction area. However, this improvement degrades a horizontal uniformity. For this, the uniform areas was no more than 55% of the total ion extraction area. In order to improve the horizontal uniformity, the filter strength has been reduced from 660 Gasuscm to 400 Gasuscm. This reduction improved the horizontal uniform area from 75% to 90% without degrading the logitudinal uniformity. This resulted in the improvement of the uniform area from 45% of the total ion extraction areas. This improvement of the uniform area leads to the production of a 22A H ion beam from 450 mm 1100 mm with a small amount increase of electron current of 10%. The obtained beam current fulfills the requirement for JT-60SA.
Tampo, Motonobu*; Hamada, Koji*; Kawamura, Naritoshi*; Inagaki, Makoto*; Ito, Takashi; Kojima, Kenji*; Kubo, Kenya*; Ninomiya, Kazuhiko*; Strasser, P.*; Yoshida, Go*; et al.
JPS Conference Proceedings (Internet), 8, p.036016_1 - 036016_6, 2015/09
Adachi, Taihei*; Ikedo, Yutaka*; Nishiyama, Kusuo*; Yabuuchi, Atsushi*; Nagatomo, Takashi*; Strasser, P.*; Ito, Takashi; Higemoto, Wataru; Kojima, Kenji*; Makimura, Shunsuke*; et al.
JPS Conference Proceedings (Internet), 8, p.036017_1 - 036017_4, 2015/09
Hiraishi, Masatoshi*; Iimura, Soshi*; Kojima, Kenji*; Yamaura, Junichi*; Hiraka, Haruhiro*; Ikeda, Kazutaka*; Miao, P.*; Ishikawa, Yoshihisa*; Torii, Shuki*; Miyazaki, Masanori*; et al.
Nature Physics, 10(4), p.300 - 303, 2014/04
Umeda, Naotaka; Kashiwagi, Mieko; Taniguchi, Masaki; Tobari, Hiroyuki; Watanabe, Kazuhiro; Dairaku, Masayuki; Yamanaka, Haruhiko; Inoue, Takashi; Kojima, Atsushi; Hanada, Masaya
Review of Scientific Instruments, 85(2), p.02B304_1 - 02B304_3, 2014/02
In order to realize neutral beam systems in ITER whose target is to produce D ion beam of 1 MeV, 200 A/m during 3600s, the electrostatic five-stages negative ion accelerator has been developed at JAEA. To extend pulse length, heat load of the acceleration grids was reduced by controlling the ion beam trajectory. Namely, the beam deflection due to the residual magnetic filter in the accelerator was suppressed with the newly developed extractor with a 0.5 mm off-set aperture displacement. The use of new extractor improved the deflection angle from 6 mrad to 1 mrad, resulting in the reduction of direct interception of negative ions from 23% to 15% of the total acceleration power, respectively. As a result, the pulse length of 130 A/m, 881 keV H ion beam has been successfully extended from a previous value of 0.4s to 8.7s.
Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Kojima, Atsushi; Yoshida, Masafumi; Taniguchi, Masaki; Dairaku, Masayuki; Maejima, Tetsuya; Yamanaka, Haruhiko; Watanabe, Kazuhiro; et al.
Review of Scientific Instruments, 85(2), p.02B320_1 - 02B320_3, 2014/02
The negative ion extractor for high power and long-pulse operations is newly developed toward the neutral beam injector (NBI) for heating & current drive of future fusion machines such as ITER, JT-60 Super Advanced (SA) and DEMO reactor. The satisfactory cooling capability is designed in the thermal analysis. A negative ion production and a suppression of electrons are experimentally validated for this new extractor. As the results, the negative ion current shows increases by a factor of 1.3 with suppressing the electron current. The beam divergence angle is also maintained small enough, 4 mrad.
Kojima, Atsushi; Hanada, Masaya; Inoue, Takashi; NB Heating Technology Group; Yamano, Yasushi*; Kobayashi, Shinichi*
Journal of the Vacuum Society of Japan, 56(12), p.502 - 506, 2013/12
Voltage holding capability of a large negative ion source for fusion application is experimentally examined, which is characterized by multiple-stage acceleration with multiple-apertures over 1000 on large-area grids of 2 m for the multiple-beamlet accelerations. From the observation of the vacuum discharge between the grids, it was found that the aperture generated 10 times larger dark current than the flat region and initiated the vacuum discharge associated with the breakdown. As a result, it was found that the sustainable voltages were dominated by not only the surface area but also the number of the apertures. Because these effects were originated in the area effects by weak and strong electric field profiles, these results implied the surface integration of the electric field were the key parameter for the vacuum insulation.
Yoshida, Masafumi; Hanada, Masaya; Kojima, Atsushi; Inoue, Takashi; Kashiwagi, Mieko; Grisham, L. R.*; Akino, Noboru; Endo, Yasuei; Komata, Masao; Mogaki, Kazuhiko; et al.
Plasma and Fusion Research (Internet), 8(Sp.1), p.2405146_1 - 2405146_4, 2013/11
Distributions of H and H in the source plasmas produced at the end-plugs of JT-60 negative ions source were measured by Langmuir probes and emission spectroscopy in order to experimentally investigate the cause of lower density of the negative ions extracted from end-plugs in the source. Densities of H and H in end-plugs of the plasma grid in the source were compared with those in the center regions. As a result, lower density of the negative ion at the edge was caused by lower beam optics due to lower and higher density of the H and H.
Kojima, Atsushi; Hanada, Masaya; Yoshida, Masafumi; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Grisham, L. R.*; et al.
Fusion Engineering and Design, 88(6-8), p.918 - 921, 2013/10
In this paper, the recent activities are reported toward demonstration of the long pulse production. As for the improvement of uniform beam current profile, a symmetric magnetic field configuration for the source plasma production, a so-called tent-shaped filter, was found to be effective to improve the uniformity of the beam current profile. A similar configuration is applied to the JT-60 negative ion source whose plasma size is 1220 mm 564 mm. An estimation from trajectory calculations of primary electrons with the symmetric magnetic field configuration showed that the primary electrons were distributed uniformly in a longitudinal direction. As for the temperature control of the plasma grid, a prototype of the grid with cooling/heating by circulating a high-temperature fluorinated fluid has been developed. This grid was found to have a capability to control the temperature with a time constant of 10 s by considering the physical properties of the fluid.
Kojima, Atsushi; Hanada, Masaya; Hilmi, A.*; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Kobayashi, Shinichi*; et al.
Review of Scientific Instruments, 83(2), p.02B117_1 - 02B117_5, 2012/02
Production of 500 keV, 3 A beams has been successfully achieved in the JT-60 negative by overcoming the low voltage holding of the accelerator. Toward the design of next ion source, database for the voltage holding capability based on experimental results is required and obtained. As a result, the voltage holding capability was found to vary with 67 N power of -0.15 and with 31.7 S power of -0.125 where N is the aperture number and S is the anode surface area. When N = 1100 and S = 2 m are applied to the design of JT-60SA ion source, the factors C are estimated to be 23 and 29, respectively. Therefore, the influence of the local electric field around the apertures is stronger than that of the surface area.