Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Shimamura, Kazutoshi*; Wajima, Hiroki*; Makino, Hayato*; Abe, Satoshi*; Haga, Yoshinori; Sato, Yoshiaki*; Kawae, Tatsuya*; Yoshida, Yasuo*
Japanese Journal of Applied Physics, 61(5), p.056502_1 - 056502_7, 2022/05
Times Cited Count:0 Percentile:0(Physics, Applied)Koizumi, Norikiyo; Matsui, Kunihiro; Shimizu, Tatsuya; Nakajima, Hideo; Iijima, Ami*; Makino, Yoshinobu*
Teion Kogaku, 47(3), p.186 - 192, 2012/03
In the ITER TF coil, cover plates (CP) are welded to teeth of a radial plate (RP) to fix a conductor in the groove of the RP. Though total length of welds is approximately 1.5 km and height and width of an RP are 14 m and 9 m, respectively, the welding deformation better than 1 mm in local distortion and several milli-meters in in-plane deformation is required. Therefore, laser welding is used for the CP welding to reduce welding deformation as possible. However, a gap of a welding joint is expected to be 0.5 mm at the maximum. Therefore, at first, the laser welding technique to enable welding on the gap of 0.5 mm width is developed in this study. Using this technology, CP welding trial using an RP mock was successfully performed. The achieved flatness is 0.6 mm. In addition, the welding deformation of a full-scale RP is estimated by the analysis using the inherent strain. The results show that the flatness of 1 mm is achievable and profile of 5 mm can be achieved. Since the in-plane deformation can be corrected by welding somewhere to originate artificial welding deformation, it is confident that the required tolerance of several milli-meters in in-plan profile is achievable.
Takano, Katsutoshi; Koizumi, Norikiyo; Shimizu, Tatsuya; Nakajima, Hideo; Esaki, Koichi*; Nagamoto, Yoshifumi*; Makino, Yoshinobu*
Teion Kogaku, 47(3), p.178 - 185, 2012/03
In the ITER TF coil, the tight tolerances of 1 mm in flatness and a few mm in profile are required in manufacturing a radial plate (RP), although the height and width of an RP are 13 m and 9 m, respectively. In addition, since cover plates (CP) should be fitted to a groove of an RP with tolerance of 0.5 mm, the tight tolerances are also required to a CP. Thus, we can conclude that the manufacturing procedure of the RP and CP has been demonstrated.
Sugita, Yutaka; Chijiwa, Tatsunori; Honda, Akira; Shibata, Masahiro; Kawaguchi, Tatsuya; Maekawa, Keisuke; Hatanaka, Koichiro; Ebashi, Takeshi; Semba, Takeshi; Makino, Hitoshi
no journal, ,
This paper reports on the development of ISRE (the Integrated System for Repository Engineering), as a knowledge management tool on repository design and engineering technology, which manages and inherits the information and knowledge of each phase of the disposal project of radioactive waste lasting around 100 years, and which also enables reasonable design of the repository by using accumulated and integrated information. The content of this paper is the conceptual design of the ISRE utilizing CIM (Computer Information Modeling) technology.
Kimura, Daisuke; Hikinuma, Yuichi; Tanabe, Masanori; Makino, Tatsuya; Maegawa, Yoshiharu; Hayata, Kenichi*; Shiotani, Junya*; Nohara, Naofumi; Hoshi, Katsuya; Tsujimura, Norio; et al.
no journal, ,
no abstracts in English