Evaluation of ductile damage in aluminum single crystal with prior activity of single slip system under tensile loading

Shibano, Junichi*; Kajiwara, Kentaro*; Tsukamoto, Takuya*; Kawai, Hirokazu*; Miura, Setsuo*; Zhang, S.*; Shobu, Takahisa

Zairyo, 63(7), p.533 - 538, 2014/07

https://doi.org/10.2472/jsms.63.533

A ductile damage progress of an aluminum single crystal with the prior activity of the single slip system under tensile loading was verified by a profile analysis using white X-ray obtained in BL28B2 beam line of SPring-8. In profile analysis, an instrumental function was defined in consideration both of a divergence by slits and a response function peculiar to the energy dispersive method. As a result, dislocation density increased as ductile damage progressed, but it was relatively low near the notch. The influence of a release of the strain energy by a ductile damage progress was expected. The characteristics of ductile damage progress near the notch of the aluminum single crystal with a prior activity of a single slip system under the tensile loading were clarified from the distribution of dislocation density.

Study on evaluation of ductile damage of aluminum single crystal using synchrotron white X-ray

Shibano, Junichi*; Kiso, Minoru*; Kajiwara, Kentaro*; Shobu, Takahisa; Miura, Setsuo*; Kobayashi, Michiaki*

Zairyo, 62(7), p.443 - 450, 2013/07

https://doi.org/10.2472/jsms.62.443

The ductile damage progress of the FCC single crystal was verified by the profile analysis using the white X-ray obtained in BL28B2 beam-line of SPring-8. In this study, an aluminum single crystal of the purity 6N was used as a specimen prepared in the I-type geometry for tensile test. The notch was introduced into one side of the center of a parallel part of the specimen by wire electric discharge machining. White X-ray, which has 200 microns in height and 100 microns in width, was incident into the specimen on the Bragg angle of 3 in the horizontal plane using energy dispersive X-ray diffraction technique. As a result, in 1.1% of applied strain, increase of the lattice strain was observed in the direction of about 45 of slant from the notch bottom. In 2.2% of applied strain, the lattice strain reduced in the direction of about 45 of slant from the notch bottom. Non-uniform strain and dislocation density decreased similarly.

Observation of internal crack of steel bar by computed tomography and strain mapping near its tip using synchrotron white X-ray

Shibano, Junichi*; Kiriyama, Koji; Kajiwara, Kentaro*; Shobu, Takahisa; Suzuki, Kenji*; Arai, Takayuki*; Miura, Setsuo*; Kobayashi, Michiaki*

Zairyo, 58(7), p.596 - 602, 2009/07

https://doi.org/10.2472/jsms.58.596

Computerized tomography of fatigue cracks in steel material using synchrotron radiation white X-rays

Kiriyama, Koji; Shibano, Junichi*; Kajiwara, Kentaro*; Shobu, Takahisa; Suzuki, Kenji*; Arai, Takayuki*; Miura, Setsuo*; Kobayashi, Michiaki*

no journal, , 

Residual stress measurement and fractographycal study of cracks are important to understand SCC (Stress Corrosion Cracking) process. In this study, CT (Computerized Tomography) imaging of steel material (alpha-Fe) have performed at BL28B2 at SPring-8. The result showed that artificial crack in the sample was clearly measured by CT, and CT are very effective tool to measure an inner state of steel material.

Strain measurement of aged duplex stainless steel using SR white X-ray

Kiriyama, Koji; Shobu, Takahisa; Shibano, Junichi*; Fujishiro, Tomoyuki; Kaneko, Hiroshi; Miura, Setsuo*

no journal, , 

Study of computerized tomography and strain mapping in the vicinity of crack tip in steel material using synchrotron white X-ray

Shibano, Junichi*; Kajiwara, Kentaro*; Kiriyama, Koji; Shobu, Takahisa; Suzuki, Kenji*; Arai, Takayuki*; Miura, Setsuo*; Kobayashi, Michiaki*

no journal, ,