Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Miura, Yasufumi*; Suzuki, Kenji*; Morooka, Satoshi; Shobu, Takahisa
Quantum Beam Science (Internet), 8(1), p.1_1 - 1_14, 2024/03
Suzuki, Kenji*; Miura, Yasufumi*; Shiro, Ayumi*; Toyokawa, Hidenori*; Saji, Choji*; Shobu, Takahisa; Morooka, Satoshi
Zairyo, 72(4), p.316 - 323, 2023/04
Suzuki, Kenji*; Kura, Komoe*; Miura, Yasufumi*; Shiro, Ayumi*; Toyokawa, Hidenori*; Saji, Choji*; Kajiwara, Kentaro*; Shobu, Takahisa
Zairyo, 71(12), p.1005 - 1012, 2022/12
This paper describes a stress measurement from a welded part of an austenitic stainless steel using synchrotron X-rays. Difficulty measuring the X-ray stress of the welded part is caused by the broadening of the diffraction spot in the radial and circumferential directions. The bending strains of the rectangular bar made of the welded part were measured using synchrotron white X-rays and the double exposure method. To improve the energy resolution, monochromatic synchrotron X-ray of 70 keV was used. The diffraction pattern showed the sharp arc like a pattern from texture material. The diffraction profile was obtained from the integral of the diffraction intensity in the direction of the circumference. The diffraction angle was determined using the double exposure method. As a result, the distribution of the residual stresses of the welded part could be measured.
Kumagai, Tomohisa*; Miura, Yasufumi*; Miura, Naoki*; Marie, S.*; Almahdi, R.*; Mano, Akihiro; Li, Y.; Katsuyama, Jinya; Wada, Yoshitaka*; Hwang, J.-H.*; et al.
Journal of Pressure Vessel Technology, 144(1), p.011509_1 - 011509_18, 2022/02
Times Cited Count：1 Percentile：20.34(Engineering, Mechanical)To predict fracture behavior for ductile materials, some ductile fracture simulation methods different from classical approaches have been investigated based on appropriate models of ductile fracture. For the future use of the methods to overcome restrictions of classical approaches, the applicability to the actual components is of concern. In this study, two benchmark problems on the fracture tests supposing actual components were provided to investigate prediction ability of simulation methods containing parameter decisions. One was the circumferentially through-wall and surface cracked pipes subjected to monotonic bending, and the other was the circumferentially through-wall cracked pipes subjected to cyclic bending. Participants predicted the ductile crack propagation behavior by their own approaches, including FEM employed GTN yielding function with void ratio criterion, are FEM employed GTN yielding function, FEM with fracture strain or energy criterion modified by stress triaxiality, XFEM with J or delta J criterion, FEM with stress triaxiality and plastic strain based ductile crack propagation using FEM, and elastic-plastic peridynamics. Both the deformation and the crack propagation behaviors for monotonic bending were well reproduced, while few participants reproduced those for cyclic bending. To reproduce pipe deformation and fracture behaviors, most of groups needed parameters which were determined toreproduce pipe deformation and fracture behaviors in benchmark problems themselves and it is still difficult to reproduce them by using parameters only from basic materials tests.
Suzuki, Kenji*; Miura, Yasufumi*; Morooka, Satoshi; Shobu, Takahisa
no journal, ,
no abstracts in English
Suzuki, Kenji*; Miura, Yasufumi*; Shiro, Ayumi*; Toyokawa, Hidenori*; Saji, Choji*; Morooka, Satoshi; Shobu, Takahisa
no journal, ,
