Pearlite growth kinetics in Fe-C-Mn eutectoid steels; Quantitative evaluation of energy dissipation at pearlite growth front via experimental approaches

Zhang, Y.-J.*; Umeda, Takemasa*; Morooka, Satoshi; Harjo, S.; Miyamoto, Goro*; Furuhara, Tadashi*

Metallurgical and Materials Transactions A, 55(10), p.3921 - 3936, 2024/10

https://doi.org/10.1007/s11661-024-07518-1

Thermal stability of retained austenite with heterogeneous composition and size in austempered Fe-2Mn-1.5Si-0.4C alloy

Watanabe, Miku*; Miyamoto, Goro*; Zhang, Y.*; Morooka, Satoshi; Harjo, S.; Kobayashi, Yasuhiro*; Furuhara, Tadashi*

ISIJ International, 64(9), p.1464 - 1476, 2024/07

https://doi.org/10.2355/isijinternational.ISIJINT-2024-044

neutron diffraction revealing the achievement of excellent combination of strength and ductility in metastable austenitic steel by grain refinement

Mao, W.; Gong, W.; Harjo, S.; Morooka, Satoshi; Gao, S.*; Kawasaki, Takuro; Tsuji, Nobuhiro*

Journal of Materials Science & Technology, 176, p.69 - 82, 2024/03

https://doi.org/10.1016/j.jmst.2023.07.036

The yield stress of Fe-24Ni-0.3C (wt.%) metastable austenitic steel increased 3.5 times (158 551 MPa) when the average grain size decreased from 35 m (coarse-grained [CG]) to 0.5 m (ultrafine-grained [UFG]), whereas the tensile elongation was kept large (0.87 0.82). neutron diffraction measurements of the CG and UFG Fe-24Ni-0.3C steels were performed during tensile deformation at room temperature to quantitatively elucidate the influence of grain size on the mechanical properties and deformation mechanisms. The initial stages of plastic deformation in the CG and UFG samples were dominated by dislocation slip, with deformation-induced martensitic transformation (DIMT) also occurring in the later stage of deformation. Results show that grain refinement increases the initiation stress of DIMT largely and suppresses the rate of DIMT concerning the strain, which is attributed to the following effects. (i) Grain refinement increased the stabilization of austenite and considerably delayed the initiation of DIMT in the 111//LD (LD: loading direction) austenite grains, which were the most stable grains for DIMT. As a result, most of the 111//LD austenite grains in the UFG specimens failed to transform into martensite. (ii) Grain refinement also suppressed the autocatalytic effect of the martensitic transformation. Nevertheless, the DIMT with the low transformation rate in the UFG specimen was more efficient in increasing the flow stress and more appropriate to maintain uniform deformation than that in the CG specimen during deformation. The above phenomena mutually contributed to the excellent combination of strength and ductility of the UFG metastable austenitic steel.

Hierarchical deformation heterogeneity during Lders band propagation in an Fe-5Mn-0.1C medium Mn steel clarified through scanning electron microscopy

Koyama, Motomichi*; Yamashita, Takayuki*; Morooka, Satoshi; Yang, Z.*; Varanasi, R. S.*; Hojo, Tomohiko*; Kawasaki, Takuro; Harjo, S.

Tetsu To Hagane, 110(3), p.205 - 216, 2024/02

https://doi.org/10.2355/tetsutohagane.TETSU-2023-052

Dynamic deformation properties of medium-Mn multi-phase steels containing retained austenite

Okitsu, Takayuki*; Hojo, Tomohiko*; Morooka, Satoshi; Miyamoto, Goro*

Tetsu To Hagane, 110(3), p.260 - 267, 2024/02

https://doi.org/10.2355/tetsutohagane.TETSU-2023-065

Impact of interatomic structural characteristics of aluminosilicate hydrate on the mechanical properties of metakaolin-based geopolymer

Kim, G.*; Cho, S.-M.*; Im, S.*; Suh, H.*; Morooka, Satoshi; Shobu, Takahisa; Kanematsu, Manabu*; Machida, Akihiko*; Bae, S.*

Construction and Building Materials, 411, p.134529_1 - 134529_18, 2024/01

https://doi.org/10.1016/j.conbuildmat.2023.134529

Multi-aspect characterization of low-temperature tempering behaviors in high-carbon martensite

Zhang, Y.*; Marusawa, Kenji*; Kudo, Kohei*; Morooka, Satoshi; Harjo, S.; Miyamoto, Goro*; Furuhara, Tadashi*

ISIJ International, 64(2), p.245 - 256, 2024/01

https://doi.org/10.2355/isijinternational.ISIJINT-2023-251

Key role of temperature on delamination in solid-state additive manufacturing via supersonic impact

Wang, Q.*; Ma, N.*; Huang, W.*; Shi, J.*; Luo, X.-T.*; Tomitaka, Sora*; Morooka, Satoshi; Watanabe, Makoto*

Materials Research Letters (Internet), 11(9), p.742 - 748, 2023/09

https://doi.org/10.1080/21663831.2023.2227221

Accuracy of measuring rebar strain in concrete using a diffractometer for residual stress analysis

Yasue, Ayumu*; Kawakami, Mayu*; Kobayashi, Kensuke*; Kim, J.; Miyazu, Yuji*; Nishio, Yuhei*; Mukai, Tomohisa*; Morooka, Satoshi; Kanematsu, Manabu*

Quantum Beam Science (Internet), 7(2), p.15_1 - 15_14, 2023/05

https://doi.org/10.3390/qubs7020015

Insight on the mechanical properties of hierarchical porous calcium-silicate-hydrate pastes according to the Ca/Si molar ratio using synchrotron X-ray scattering and nanoindentation test

Im, S.*; Jee, H.*; Suh, H.*; Kanematsu, Manabu*; Morooka, Satoshi; Choe, H.*; Nishio, Yuhei*; Machida, Akihiko*; Kim, J.*; Lim, S.*; et al.

Construction and Building Materials, 365, p.130034_1 - 130034_18, 2023/02

https://doi.org/10.1016/j.conbuildmat.2022.130034