Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Tamii, Atsushi*; Pellegri, L.*; S
derstrm, P.-A.*; Allard, D.*; Goriely, S.*; Inakura, Tsunenori*; Khan, E.*; Kido, Eiji*; Kimura, Masaaki*; Litvinova, E.*; et al.
European Physical Journal A, 59(9), p.208_1 - 208_21, 2023/09
Times Cited Count：1 Percentile：0.02(Physics, Nuclear)no abstracts in English
Toyoda, Shin*; Inoue, Kazuhiko*; Yamaguchi, Ichiro*; Hoshi, Masaharu*; Hirota, Seiko*; Oka, Toshitaka; Shimazaki, Tatsuya*; Mizuno, Hideyuki*; Tani, Atsushi*; Yasuda, Hiroshi*; et al.
Radiation Protection Dosimetry, 199(14), p.1557 - 1564, 2023/09
Times Cited Count：0 Percentile：0.01(Environmental Sciences)Interlaboratory comparison studies are important for radiation dosimetry in order to demonstrate how the technique is universally available. The set of standard samples are examined in each participating laboratory in the present study. After a set of standard samples together with the samples with unknown doses, which were prepared in the same laboratory as the standard samples, are measured at a participating laboratory, those samples are sent to another participating laboratory for next measurement. There is some small difference observed in the sensitivity (the slope of the dose response line) of the standard samples while the differences in the obtained doses for the samples with unknown doses are rather systematic, implying that the difference is mostly due to the samples but not to measurements.
Ohshima, Hiroyuki; Morishita, Masaki*; Aizawa, Kosuke; Ando, Masanori; Ashida, Takashi; Chikazawa, Yoshitaka; Doda, Norihiro; Enuma, Yasuhiro; Ezure, Toshiki; Fukano, Yoshitaka; et al.
Sodium-cooled Fast Reactors; JSME Series in Thermal and Nuclear Power Generation, Vol.3, 631 Pages, 2022/07
This book is a collection of the past experience of design, construction, and operation of two reactors, the latest knowledge and technology for SFR designs, and the future prospects of SFR development in Japan. It is intended to provide the perspective and the relevant knowledge to enable readers to become more familiar with SFR technology.
Koyama, Shinichi; Nakagiri, Toshio; Osaka, Masahiko; Yoshida, Hiroyuki; Kurata, Masaki; Ikeuchi, Hirotomo; Maeda, Koji; Sasaki, Shinji; Onishi, Takashi; Takano, Masahide; et al.
Hairo, Osensui Taisaku jigyo jimukyoku Homu Peji (Internet), 144 Pages, 2021/08
JAEA performed the subsidy program for the "Project of Decommissioning and Contaminated Water Management (Development of Analysis and Estimation Technology for Characterization of Fuel Debris (Development of Technologies for Enhanced Analysis Accuracy and Thermal Behavior Estimation of Fuel Debris))" in 2020JFY. This presentation summarized briefly the results of the project, which will be available shortly on the website of Management Office for the Project of Decommissioning and Contaminated Water Management.
clusters in dilute neutron-rich matterTanaka, Junki*; Yang, Z.*; Typel, S.*; Adachi, Satoshi*; Bai, S.*; van Beek, P.*; Beaumel, D.*; Fujikawa, Yuki*; Han, J.*; Heil, S.*; et al.
Science, 371(6526), p.260 - 264, 2021/01
Times Cited Count：48 Percentile：99.12(Multidisciplinary Sciences)By employing quasi-free -cluster-knockout reactions, we obtained direct experimental evidence for the formation of clusters at the surface of neutron-rich tin isotopes. The observed monotonous decrease of the reaction cross sections with increasing mass number, in excellent agreement with the theoretical prediction, implies a tight interplay between -cluster formation and the neutron skin.
Tsuji, Tomoyuki; Sugitsue, Noritake; Sato, Fuminori; Matsushima, Ryotatsu; Kataoka, Shoji; Okada, Shota; Sasaki, Toshiki; Inoue, Junya
Nihon Genshiryoku Gakkai-Shi ATOMO
, 62(11), p.658 - 663, 2020/11
no abstracts in English
Omori, Atsushi*; Akiyama, Eiji*; Abe, Hiroshi*; Hata, Kuniki; Sato, Tomonori; Kaji, Yoshiyuki; Inoue, Hiroyuki*; Taguchi, Mitsumasa*; Seito, Hajime*; Tada, Eiji*; et al.
Zairyo To Kankyo, 69(4), p.107 - 111, 2020/04
To evaluate the effect of oxidants, which are formed by radiolysis of water under gamma ray irradiation, on the corrosion of a carbon steel in humid environment, ozone was introduced as a model oxidant in to humidity-controlled air at 50
C in a thermo-hygrostat chamber. Corrosion monitoring was performed by using an Atmospheric Corrosion Monitor-type (ACM) sensor consisting of a carbon steel anode and an Ag cathode. The output current of the ACM sensor was increased with the increase in relative humidity and it was obviously increased with the increase in the introduced ozone concentration at each relative humidity. The results indicate that ozone accelerates the corrosion of the carbon steel. The effect of ozone on the corrosion acceleration is attributed to the fast reduction reaction and fast dissolution reaction in to water compared to that of oxygen.
laser stripping at J-PARC 3-GeV RCSSaha, P. K.; Harada, Hiroyuki; Kinsho, Michikazu; Miura, Akihiko; Yoshimoto, Masahiro; Okabe, Kota; Suganuma, Kazuaki; Yamane, Isao*; Irie, Yoshiro*; Liu, Y.*; et al.
Proceedings of 15th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.806 - 810, 2018/08
Harada, Hiroyuki; Saha, P. K.; Yoneda, Hitoki*; Michine, Yurina*; Inoue, Shunsuke*; Sato, Atsushi*; Suganuma, Kazuaki; Yamane, Isao*; Kinsho, Michikazu; Irie, Yoshiro*
Proceedings of 15th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.811 - 815, 2018/08
The high-intensity proton accelerator adopts a charge exchange injection scheme, which injects with exchanging from negative Hydrogen ion to proton by using carbon foil. This scheme can realize high intensity proton beam but the uncontrolled beam losses occur by scattering at the foil. Additionally, the beam collision at the foil may cause the break itself. Therefore, a new injection scheme for higher intensity is needed as an alternative to the foil. We newly propose and develop a laser stripping injection scheme. At the first step, we propose a proof-of-principle (POP) experiment of the scheme in J-PARC and develop a laser system. In this presentation, we will introduce the laser stripping injection scheme and describe an overview of a POP experiment. We will report a current status of the laser system.
Tsukasaki, Yoshikazu*; Miyazaki, Naoyuki*; Matsumoto, Atsushi; Nagae, Shigenori*; Yonemura, Shigenobu*; Tanoue, Takuji*; Iwasaki, Kenji*; Takeichi, Masatoshi*
Proceedings of the National Academy of Sciences of the United States of America, 111(45), p.16011 - 16016, 2014/11
Times Cited Count：38 Percentile：63.74(Multidisciplinary Sciences) ion beams for ITER NB acceleratorUmeda, Naotaka; Kashiwagi, Mieko; Taniguchi, Masaki; Tobari, Hiroyuki; Watanabe, Kazuhiro; Dairaku, Masayuki; Yamanaka, Haruhiko; Inoue, Takashi; Kojima, Atsushi; Hanada, Masaya
Review of Scientific Instruments, 85(2), p.02B304_1 - 02B304_3, 2014/02
Times Cited Count：12 Percentile：48.5(Instruments & Instrumentation)In order to realize neutral beam systems in ITER whose target is to produce D ion beam of 1 MeV, 200 A/m
during 3600s, the electrostatic five-stages negative ion accelerator has been developed at JAEA. To extend pulse length, heat load of the acceleration grids was reduced by controlling the ion beam trajectory. Namely, the beam deflection due to the residual magnetic filter in the accelerator was suppressed with the newly developed extractor with a 0.5 mm off-set aperture displacement. The use of new extractor improved the deflection angle from 6 mrad to 1 mrad, resulting in the reduction of direct interception of negative ions from 23% to 15% of the total acceleration power, respectively. As a result, the pulse length of 130 A/m, 881 keV H ion beam has been successfully extended from a previous value of 0.4s to 8.7s.
Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Kojima, Atsushi; Yoshida, Masafumi; Taniguchi, Masaki; Dairaku, Masayuki; Maejima, Tetsuya; Yamanaka, Haruhiko; Watanabe, Kazuhiro; et al.
Review of Scientific Instruments, 85(2), p.02B320_1 - 02B320_3, 2014/02
Times Cited Count：29 Percentile：75.28(Instruments & Instrumentation)The negative ion extractor for high power and long-pulse operations is newly developed toward the neutral beam injector (NBI) for heating & current drive of future fusion machines such as ITER, JT-60 Super Advanced (SA) and DEMO reactor. The satisfactory cooling capability is designed in the thermal analysis. A negative ion production and a suppression of electrons are experimentally validated for this new extractor. As the results, the negative ion current shows increases by a factor of 1.3 with suppressing the electron current. The beam divergence angle is also maintained small enough, 4 mrad.
Kojima, Atsushi; Hanada, Masaya; Inoue, Takashi; NB Heating Technology Group; Yamano, Yasushi*; Kobayashi, Shinichi*
Journal of the Vacuum Society of Japan, 56(12), p.502 - 506, 2013/12
Voltage holding capability of a large negative ion source for fusion application is experimentally examined, which is characterized by multiple-stage acceleration with multiple-apertures over 1000 on large-area grids of 2 m for the multiple-beamlet accelerations. From the observation of the vacuum discharge between the grids, it was found that the aperture generated 10 times larger dark current than the flat region and initiated the vacuum discharge associated with the breakdown. As a result, it was found that the sustainable voltages were dominated by not only the surface area but also the number of the apertures. Because these effects were originated in the area effects by weak and strong electric field profiles, these results implied the surface integration of the electric field were the key parameter for the vacuum insulation.
Yoshida, Masafumi; Hanada, Masaya; Kojima, Atsushi; Inoue, Takashi; Kashiwagi, Mieko; Grisham, L. R.*; Akino, Noboru; Endo, Yasuei; Komata, Masao; Mogaki, Kazuhiko; et al.
Plasma and Fusion Research (Internet), 8(Sp.1), p.2405146_1 - 2405146_4, 2013/11
Distributions of H
and H
in the source plasmas produced at the end-plugs of JT-60 negative ions source were measured by Langmuir probes and emission spectroscopy in order to experimentally investigate the cause of lower density of the negative ions extracted from end-plugs in the source. Densities of H and H in end-plugs of the plasma grid in the source were compared with those in the center regions. As a result, lower density of the negative ion at the edge was caused by lower beam optics due to lower and higher density of the H and H.
Kojima, Atsushi; Hanada, Masaya; Yoshida, Masafumi; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Grisham, L. R.*; et al.
Fusion Engineering and Design, 88(6-8), p.918 - 921, 2013/10
Times Cited Count：6 Percentile：44.02(Nuclear Science & Technology)In this paper, the recent activities are reported toward demonstration of the long pulse production. As for the improvement of uniform beam current profile, a symmetric magnetic field configuration for the source plasma production, a so-called tent-shaped filter, was found to be effective to improve the uniformity of the beam current profile. A similar configuration is applied to the JT-60 negative ion source whose plasma size is 1220 mm 
564 mm. An estimation from trajectory calculations of primary electrons with the symmetric magnetic field configuration showed that the primary electrons were distributed uniformly in a longitudinal direction. As for the temperature control of the plasma grid, a prototype of the grid with cooling/heating by circulating a high-temperature fluorinated fluid has been developed. This grid was found to have a capability to control the temperature with a time constant of 10 s by considering the physical properties of the fluid.
Kiriyama, Hiromitsu; Shimomura, Takuya; Mori, Michiaki; Nakai, Yoshiki*; Tanoue, Manabu; Kondo, Shuji; Kanazawa, Shuhei; Pirozhkov, A. S.; Esirkepov, T. Z.; Hayashi, Yukio; et al.
Applied Sciences (Internet), 3(1), p.214 - 250, 2013/03
Times Cited Count：15 Percentile：50(Chemistry, Multidisciplinary)This paper reviews techniques for improving the temporal contrast and spatial beam quality in an ultra-intense laser system that is based on chirped-pulse amplification (CPA). We describe the design, performance, and characterization of our laser system, which has the potential for achieving a peak power of 600 TW. We also describe applications of the laser system in the relativistically dominant regime of laser-matter interactions and discuss a compact, high efficiency diode-pumped laser system.
Kojima, Atsushi; Hanada, Masaya; Hilmi, A.*; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Kobayashi, Shinichi*; et al.
Review of Scientific Instruments, 83(2), p.02B117_1 - 02B117_5, 2012/02
Times Cited Count：17 Percentile：60.55(Instruments & Instrumentation)Production of 500 keV, 3 A beams has been successfully achieved in the JT-60 negative by overcoming the low voltage holding of the accelerator. Toward the design of next ion source, database for the voltage holding capability based on experimental results is required and obtained. As a result, the voltage holding capability was found to vary with 67 N power of -0.15 and with 31.7 S power of -0.125 where N is the aperture number and S is the anode surface area. When N = 1100 and S = 2 m are applied to the design of JT-60SA ion source, the factors C are estimated to be 23 and 29, respectively. Therefore, the influence of the local electric field around the apertures is stronger than that of the surface area.
Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Dairaku, Masayuki; Takemoto, Jumpei; Tobari, Hiroyuki; Tsuchida, Kazuki; Yamanaka, Haruhiko; Watanabe, Kazuhiro; Kojima, Atsushi; et al.
Review of Scientific Instruments, 83(2), p.02B121_1 - 02B121_3, 2012/02
Times Cited Count：11 Percentile：46.97(Instruments & Instrumentation)JAEA has developed the MeV accelerator to demonstrate 1 MeV, 200 A/m H ion beam acceleration required for ITER NBI. A key to realize such a high power accelerator is improvement of voltage holding capability. Based on detailed investigation of the voltage holding characteristics, MeV accelerator was modified to reduce electric field concentration by extending gaps between the grid supports and increasing curvature radiuses at the support corners. After the modifications, accelerator succeeded in sustaining -1 MV in vacuum without beam acceleration. Moreover, beam deflection due to the magnetic field for electron suppression and space charge repulsion was compensated by aperture displacement technique. As the result, beam deflection was compensated and voltage holding during the beam acceleration was improved. Beam parameter of the MeV accelerator was increased to 980 keV, 185 A/m, which is close to the requirement of ITER accelerator.
Hanada, Masaya; Kojima, Atsushi; Tanaka, Yutaka; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Tobari, Hiroyuki; Umeda, Naotaka; Akino, Noboru; et al.
Fusion Engineering and Design, 86(6-8), p.835 - 838, 2011/10
Times Cited Count：13 Percentile：69.64(Nuclear Science & Technology)Neutral beam (NB) injectors for JT-60 Super Advanced (JT-60SA) have been designed and developed. Twelve positive-ion-based and one negative-ion-based NB injectors are allocated to inject 30 MW D beams in total for 100 s. Each of the positive-ion-based NB injector is designed to inject 1.7 MW for 100s at 85 keV. A part of the power supplies and magnetic shield utilized on JT-60U are upgraded and reused on JT-60SA. To realize the negative-ion-based NB injector for JT-60SA where the injection of 500 keV, 10 MW D beams for 100s is required, R&Ds of the negative ion source have been carried out. High-energy negative ion beams of 490-500 keV have been successfully produced at a beam current of 1-2.8 A through 20% of the total ion extraction area, by improving voltage holding capability of the ion source. This is the first demonstration of a high-current negative ion acceleration of 
1 A to 500 keV. The design of the power supplies and the beamline is also in progress. The procurement of the acceleration power supply starts in 2010.
Nogiwa, Kimihiro; Nishimura, Akihiko; Yokoyama, Atsushi; Otsuka, Satoshi; Kaito, Takeji; Inoue, Masaki; Okubo, Tadakatsu*; Hono, Kazuhiro*
Journal of Nuclear Materials, 417(1-3), p.201 - 204, 2011/10
Times Cited Count：8 Percentile：53.37(Materials Science, Multidisciplinary)Du se 9Cr-ODS (oxide dispersion-strengthened) steel consisting of residual- ferrite and prime martensite has excellent high-temperature strength. This study describes the microstructure of dual-phase 9Cr-ODS steels characterized by atom-probe tomography in order to compare oxide-particle dispersion states in each phase. This revealed that nano-size oxide particles were of the same chemical composition and that their mean size was about 3 nm in each phase. On the other hand, the number density in the residual- phase was about four times higher than that of the prime phase. These results indicate that the dense distribution of the oxide particles in the residual- phase contribute to the excellent high-temperature strength of 9Cr-ODS steel.
