Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Lin, Z. M.*; Liu, B. X.*; Ming, K. S.*; 徐 平光; Yin, F. X.*; Zheng, S. J.*
Scripta Materialia, 263, p.116692_1 - 116692_7, 2025/07
被引用回数：0 パーセンタイル：0.00(Nanoscience & Nanotechnology)Complementary layer thickness effects on strength and plasticity in Q235 and SUS304 steels provide a novel strategy to realize high strength and high plasticity of heterogeneous Q235/SUS304 multilayered steel. In this work, the tensile deformation behaviors and fracture characteristics of vacuum hot-rolled Q235/SUS304 multilayered steel with various layer thicknesses ranging from 223 
m to 5 m were deeply investigated. The tensile strength improved with the reduction of layer thickness, and the uniform elongation were first increasing and then decreasing with the decrease of layer thickness, and the peak value appeared at the layer thickness of 20 m. Interestingly, the fracture elongation forms a high plateau value within the 10
20 m range. Further analysis reveals that the severe strain localization in the brittle SUS304 thin layers is delayed by the ductile Q235 layers, which is mainly attributed to the different texture evolution and dislocation configuration characteristics during tensile deformation.
Hu, F.-F.*; Qin, T.-Y.*; Ao, N.*; 徐 平光; Su, Y. H.; Parker, J. D.*; 篠原 武尚; 菖蒲 敬久; Kang, G.-Z.*; Ren, M.-M.; et al.
Journal of Traffic and Transportation Engineering, 25(2), p.75 - 93, 2025/04
To accurately predict the remaining lifetime of surface-strengthened railway axles, a damage tolerance method considering three-dimensional (3D) residual stresses was proposed. By taking the induction-hardened carbon steel S38C axle as an example, two-dimensional (2D) distribution characterization of residual strain and 3D residual stress measurement were performed through comprehensive application of the neutron Bragg-edge transmission imaging and angle-dispersive neutron diffraction experiments. A numerical method was employed to implant the 3D residual stress into the axle model, and the remaining lifetime of the full-scale axle was studied by coupling the measured load spectrum, press-fit loads, and residual stresses. Experimental results shows that, both axial and hoop directions present a compressive residual strain gradient layer of about 3 mm, with a maximum compressive residual strain of up to -4500 
in the surface layer, yet a maximum tensile strain of up to 1000 in the core. The maximum axial and hoop compressive stresses of the axle are about -500 MPa and -303 MPa respectively, while radial stresses overall fluctuate in the zero mean stress range. At depths beyond 4.5 mm from the surface layer, all three components are tensile stresses. The axle surface layer is subjected to compressive residual stresses, and crack propagation does not occur if the crack depth is less than 4.5 mm. Nevertheless, cracks propagate accelerates when the crack depth is greater than 4.5 mm. Different crack propagation depth thresholds lead to a larger calculated remaining lifetime for the residual stress-free condition than for the case where 3D residual stresses are taken into account. However, the axle remaining service mileage of the axle of 227000 Km under the most conservative conditions exceeds 3.5 non-destructive inspection (NDI) cycles, with a large safety margin. The experimental results can provide a scientific reference for the development and optimization of NDI cycles for surface-strengthened railway axles.
Liu, P.-F.*; Li, X.*; Li, J.*; Zhu, J.*; Tong, Z.*; 古府 麻衣子*; 楡井 真実; Xu, J.*; Yin, W.*; Wang, F.*; et al.
National Science Review, 11(12), p.nwae216_1 - nwae216_10, 2024/12
被引用回数：13 パーセンタイル：94.32(Multidisciplinary Sciences)Crystalline solids exhibiting inherently low lattice thermal conductivity (
) are of great importance in applications such as thermoelectrics and thermal barrier coatings. However, cannot be arbitrarily low and is limited by the minimum thermal conductivity related to phonon dispersions. In this work, we report the liquid-like thermal transport in a well-ordered crystalline CsAg
Te
, which exhibits an extremely low value of 0.18 Wm
K. On the basis of first-principles calculations and inelastic neutron scattering measurements, we find that there are lots of low-lying optical phonon modes at 3.1 meV hosting the avoided-crossing behavior with acoustic phonons. These strongly localized modes are accompanied by weakly bound rattling Ag atoms with thermally induced large amplitudes of vibrations. Using the two-channel model, we demonstrate that coupling of the particle-like phonon modes and the heat-carrying wave-like phonons is essential for understanding the low , which is heavily deviated from the 
temperature dependence of the standard Peierls theory. In addition, our analysis indicates that the soft structural framework with liquid-like motions of the fluctuating Ag atoms is the underlying cause that leads to the suppression of the heat conduction in CsAgTe. These factors synergistically account for the ultralow value. Our results demonstrate that the liquid-like heat transfer could indeed exist in a well-ordered crystal.
Liao, J.*; Huang, Z.*; Shangguan, Y.*; Zhang, B.*; Cheng, S.*; Xu, H.*; 梶本 亮一; 蒲沢 和也*; Bao, S.*; Wen, J.*
Physical Review B, 109(22), p.224411_1 - 224411_10, 2024/06
被引用回数：0 パーセンタイル：0.00(Materials Science, Multidisciplinary)Antiferromagnetic van der Waals family 
P
( = Fe, Mn, Co, and Ni; 
= S and Se) have attracted significant research attention due to the possibility of realizing long-range magnetic order down to the monolayer limit. Here, we perform inelastic neutron scattering measurements on single-crystal samples of MnPSe, a member of the P family, to study the spin dynamics and determine the effective spin model. The excited magnon bands are well characterized by a spin model, which includes a Heisenberg term with three intraplane exchange parameters (
meV, 
meV, 
meV) and one interplane parameter (
meV), and an easy-plane single-ion anisotropy term (
meV). Additionally, we observe the intersection of the magnon and phonon bands but no anomalous spectral features induced by the formation of magnon-phonon hybrid excitations at the intersecting region. We discuss possible reasons for the absence of such hybrid excitations in MnPSe.
FCC hierarchical martensite transformation under dynamic impact in FeMnAlNiTi alloyLi, C.*; Fang, W.*; Yu, H. Y.*; Peng, T.*; Yao, Z. T.*; Liu, W. G.*; Zhang, X.*; 徐 平光; Yin, F.*
Materials Science & Engineering A, 892, p.146096_1 - 146096_11, 2024/02
被引用回数：6 パーセンタイル：79.11(Nanoscience & Nanotechnology)The quasi-static superelastic responses and hierarchical martensite transformation from body-centered cubic (BCC) to face-centered cubic (FCC) under dynamic impact in Fe
Mn
Al
Ni
Ti
alloys were investigated. Polycrystalline and oligocrystalline alloys were produced through solution heat treatment and cyclic heat treatment processes, respectively. The results show the volume fraction of residual martensite for oligocrystalline alloys is lower, which exhibits better superelastic responses compared with polycrystalline alloys. Dynamic impact tests indicate that, despite the weakening of the grain boundary strengthening effect, the ultimate strength of the oligocrystalline alloys closely matches that of the polycrystalline alloys under dynamic impact. The martensite transformation of the FeMnAlNiTi alloy is characterized as hierarchical under dynamic impact, and increasing strain rates and grain sizes can enhance the BCC FCC martensite transformation, resulting in higher martensite phase fractions for oligocrystalline alloys. The increase in ultimate strength is attributed to the dynamic Hall-Petch effect introduced by more martensite phase interfaces under dynamic impact.
Ao, N.*; Zhang, H.*; Xu, H. H.*; Wu, S. C.*; Liu, D.*; 徐 平光; Su, Y. H.; Kang, Q. H.*; Kang, G. Z.*
Engineering Fracture Mechanics, 281, p.109166_1 - 109166_14, 2023/03
被引用回数：13 パーセンタイル：82.23(Mechanics)Considering the complex service environments that high-speed railway axles are subjected to, the fatigue crack growth (FCG) behavior of a structurally gradient axle steel with different pre-crack depths both in air and corrosive medium was investigated at a frequency of 5 Hz. The results indicated that in the high 
region, FCG rate was dramatically accelerated by corrosion, but the gap narrows as decreased. The accelerated corrosion FCG rate was a comprehensive result of the acceleration effect of the anodic dissolution, hydrogen-enhanced localized plasticity and the retardation effect of corrosion-induced crack-tip blunting. Despite the fact that the corrosion resistance gradually decreased as the pre-crack depth increased, the FCG rate in the corrosive medium gradually decreased. This was because fatigue loading played a more important role than corrosion in accelerating the corrosion FCG rate.
Jiang, X.*; 服部 高典; Xu, X.*; Li, M.*; Yu, C.*; Yu, D.*; Mole, R.*; 矢野 真一郎*; Chen, J.*; He, L.*; et al.
Materials Horizons, 10(3), p.977 - 982, 2023/03
被引用回数：26 パーセンタイル：93.14(Chemistry, Multidisciplinary)現在の蒸気圧縮式冷凍機に代わる環境に優しい冷凍機として、バロカロリック効果に基づく固体冷凍機が世界的に注目されている。一般に、バロカロリック効果が発現する相はいずれも常圧でも存在する。ここでは、それらの物質と違って、KPF
が高圧の菱面体晶相を生成することにより、巨大なバロカロリック効果を示すことを実証した。相図は、圧力依存の熱量測定、ラマン散乱測定、中性子回折測定に基づいて構築されたものである。本研究は、巨大バロカロリー効果に、高圧相の生成という新たな手法をもたらすと期待される。
Miao, Z.-Q.*; Xia, C.-J.*; Lai, X.-Y.*; 丸山 敏毅; Xu, R.-X.*; Zhou, E.-P.*
International Journal of Modern Physics E, 31(4), p.2250037_1 - 2250037_20, 2022/04
被引用回数：11 パーセンタイル：84.55(Physics, Nuclear)It is suggested that pulsar-like compact stars are comprised entirely of strangeons (quark-clusters with three-light-flavor symmetry) and a small amount of electrons. To constrain the properties of strangeon stars, we propose a linked bag model to describe matter with the strong interaction in both 2-flavored (nucleons) and 3-flavored (hyperons, strangeons, etc.) scenarios. The parameters are calibrated to reproduce the saturation properties of nuclear matter. The energy per baryon of strangeon matter is smaller than that of baryon matter if the strangeon carries a large number of valence quarks, which stiffens the equation of state and consequently increases the maximum mass of strangeon stars. The maximum mass and tidal deformability of strangeon stars within the present model are consistent with the observation, i.e. the maximum mass of strangeon stars can be 2.5 solar mass, and the tidal deformability of a 1.4 solar mass star can be 
.
Fe(n,
)
Fe cross section from the surrogate ratio method and its effect on the Fe nucleosynthesisYan, S. Q.*; Li, X. Y.*; 西尾 勝久; Lugaro, M.*; Li, Z. H.*; 牧井 宏之; Pignatari, M.*; Wang, Y. B.*; Orlandi, R.; 廣瀬 健太郎; et al.
Astrophysical Journal, 919(2), p.84_1 - 84_7, 2021/10
被引用回数：5 パーセンタイル：33.27(Astronomy & Astrophysics)The long-lived Fe (with a half-life of 2.62 Myr) is a crucial diagnostic of active nucleosynthesis in the Milky Way galaxy and in supernovae near the solar system. The neutron-capture reaction Fe(n,)Fe on Fe (half-life=44.5 days) is the key reaction for the production of Fe in massive stars. This reaction cross section has been previously constrained by the Coulomb dissociation experiment, which offered partial constraint on the E1 -ray strength function but a negligible constraint on the M1 and E2 components. In this work, for the first time, we use the surrogate ratio method to experimentally determine the Fe(n,)Fe cross sections in which all the components are included. We derived a Maxwellian-averaged cross section of 27.5
3.5 mb at 
= 30 keV and 13.41.7 mb at = 90 keV, roughly 10%-20% higher than previous estimates. We analyzed the impact of our new reaction rates in nucleosynthesis models of massive stars and found that uncertainties in the production of Fe from the Fe(n,)Fe rate are at most 25
. We conclude that stellar physics uncertainties now play a major role in the accurate evaluation of the stellar production of Fe.
Xu, Z.*; Dai, G.*; Li, Y.*; Yin, Z.*; Rong, Y.*; Tian, L.*; Liu, P.*; Wang, H.*; Xing, L.*; Wei, Y.*; et al.
npj Quantum Materials (Internet), 5(1), p.11_1 - 11_7, 2020/02
被引用回数：4 パーセンタイル：33.13(Materials Science, Multidisciplinary)We use neutron scattering to study Vanadium (hole)-doped LiFe
V
As. In the undoped state, LiFeAs exhibits superconductivity at 
K and transverse incommensurate spin excitations similar to electron overdoped iron pnictides. Upon Vanadium doping to form LiFe
V
, the transverse incommensurate spin excitations in LiFeAs transform into longitudinally elongated ones in a similar fashion to that of potassium (hole)-doped Ba
K
Fe
As but with dramatically enhanced magnetic scattering and elimination of superconductivity. This is different from the suppression of the overall magnetic excitations in hole-doped BaFeAs and the enhancement of superconductivity near optimal hole doping. These results are consistent with density function theory plus dynamic mean field theory calculations, suggesting that Vanadium doping in LiFeAs may induce an enlarged effective magnetic moment 
with a spin crossover ground state arising from the inter-orbital scattering of itinerant electrons.
Pd
and 
Pd
; Competing proton and neutron excitations in neutron-rich palladium nuclides towards the 
shell closure渡邉 寛*; Wang, H. K.*; Lorusso, G.*; 西村 俊二*; Xu, Z. Y.*; 炭竃 聡之*; Orlandi, R.; 他47名*
Physics Letters B, 792, p.263 - 268, 2019/05
被引用回数：6 パーセンタイル：46.80(Astronomy & Astrophysics)The isotopes Pd and Pd, respectively with 79 and 81 neutrons, are key isotopes to understand the evolution of the N=82 shell closure below 
Pd. These nuclei were studied at RIBF (RIKEN). New isomeric states with half-lives of 144(4) ns and 39(6) s were assigned spins and parities of (23/2
) and (19/2) in Pd and Pd, respectively. The assignment was carried out based on the results of the -ray intensity balance analysis and the measured transition strengths with the aid of a shell-model calculation. The isomoer in Pd was ascribed predominantly to three neutron-hole excitations in the N=50-82 shell. The 19/2 state in Pd is expected to involve the coupling of proton and neutron configurations. The new data will provide important benchmarks for a better understanding of 
-process nucleosynthesis.
Tang, C.*; Song, Q.*; Chang, C.-Z.*; Xu, Y.*; 大沼 悠一; 松尾 衛*; Liu, Y.*; Yuan, W.*; Yao, Y.*; Moodera, J. S.*; et al.
Science Advances (Internet), 4(6), p.eaas8660_1 - eaas8660_6, 2018/06
被引用回数：34 パーセンタイル：83.43(Multidisciplinary Sciences)This work demonstrates markedly modified spin dynamics of magnetic insulator (MI) by the spin momentum-locked Dirac surface states of the adjacent topological insulator (TI). As the Bi concentration 
is systematically tuned in 5-nm-thick (BiSb)Te TI films, the weight of the surface relative to bulk states peaks at = 0.32 when the chemical potential approaches the Dirac point. At this concentration, the Gilbert damping constant of the precessing magnetization in 10-nm-thick YFe
O
MI films in the MI/TI heterostructures is enhanced by an order of magnitude, the largest among all concentrations. In addition, the MI acquires additional strong magnetic anisotropy that favors the in-plane orientation with similar Bi concentration dependence. These extraordinary effects of the Dirac surface states distinguish TI from other materials such as heavy metals in modulating spin dynamics of the neighboring magnetic layer.
Wang, Y.-Q.*; Gai, W.-Z.*; Zhang, X.-Y.*; Pan, H.-Y.*; Cheng, Z.-X.*; 徐 平光; Deng, Z.-Y.*
RSC Advances (Internet), 7(4), p.2103 - 2109, 2017/01
被引用回数：28 パーセンタイル：63.30(Chemistry, Multidisciplinary)Al powder was stored in saturated water vapor, oxygen, nitrogen and drying air separately for a time period up to about six months, the degradation behavior of Al activity was characterized by the reaction of Al with water. It was found that water vapor decreased the induction time for the beginning of Al-water reaction and reduced the total hydrogen generation per unit weight of Al, while oxygen increased the induction time and retarded the Al-water reaction. In contrast, the effect of nitrogen and drying air on Al activity was weak. The mechanism analyses indicated that water vapor promoted the hydration of Al surface passive oxide film and speeded up the reaction of Al with water, while oxygen thickened the passive oxide film of Al surface and prolonged its hydration process. These imply that water vapor rather than oxygen is responsible for the degradation of Al activity during storage under ambient condition.
suspensionLiang, G.-H.*; Gai, W.-Z.*; Deng, Z.-Y.*; 徐 平光; Cheng, Z.*
RSC Advances (Internet), 6(42), p.35305 - 35314, 2016/04
被引用回数：19 パーセンタイル：51.42(Chemistry, Multidisciplinary)Hydrogen is an ideal fuel for fuel cells because its reaction byproduct with oxygen is environmentally benign. To resolve the safe storage and low cost transportation problem, the onsite hydrolysis reaction in water has been recently employed as a new-type portable hydrogen source. Metal Al is thought as a promising hydrogen-generation material due to its relative low price, light atomic weight and abundance in the earth. In order to promote the reaction of Al particles with water and weaken the inhabitation phenomenon of dense passive oxide film on Al surface, the effect of ultrasonically prepared Al(OH) suspension on the kinetics of Al-water reaction was investigated in this paper. It is found that the induction time for the beginning of Al-water reaction decreases and the reaction rate increases with increasing the suspension concentration, volume and temperature, which is ascribed to the exothermic characteristics of Al-water reaction.
Xu, Z.; Gu, B.; 森 道康; Ziman, T.*; 前川 禎通
Journal of Magnetism and Magnetic Materials, 400, p.184 - 187, 2016/02
被引用回数：4 パーセンタイル：19.41(Materials Science, Multidisciplinary)We perform a systematical analysis of the spin Hall effect (SHE) in the Cu alloys doped with a series of 5d elements, by the combined approach of density functional theory and Hartree-Fock approximation. We find that not only the spin orbit interactions (SOI) in both the 5d and 6p orbitals, but also the local correlations in the 5d orbitals of the impurities, are decisive on the sign of the spin Hall angle (SHA). Including all of these three factors properly, we predict the SHA for each alloy in the series. The signs of CuIr and CuPt are sensitive to perturbation of the local correlations. This observation is favorable for controlling the sign of the transverse spin Hall voltage.
Xu, Z.*; 山地 宏志*; 佐藤 稔紀; 松井 裕哉; 板倉 賢一*
土木学会論文集,F3(土木情報学)(インターネット), 71(1), p.43 - 55, 2015/10
地下空間開発の過程では、調査・計画・設計・施工の各ステージにおいて膨大な情報が収集される。地下空間の合理的設計・施工を実現するためには、これらの情報を適確に設計施工へとフィードバックすることが重要となる。また、構造物管理の面においてもこれらの情報はその基礎資料となるものである。しかしながら、実際に収集される情報量は余りにも膨大なため、個人の能力でこれらを管理することは不可能に近い。本論文では、WEB3DとRDBMSを援用して4次元仮想現実空間をPC上に構築し、この仮想現実空間内を自由に移動することで、この膨大な情報群を直感的に管理・処理することのできるシステムの基本構造を設計し、その実用性を検証した。
Xu, Z.; Gu, B.; 森 道康; Ziman, T.*; 前川 禎通
Journal of Applied Physics, 117(17), p.17D510_1 - 17D510_4, 2015/05
被引用回数：4 パーセンタイル：17.16(Physics, Applied)We analyze the spin Hall effect in CuIr alloys in theory by the combined approach of the density functional theory (DFT) and Hartree-Fock (HF) approximation. The spin Hall angle (SHA) is obtained to be negative without the local correlation effects. After including the local correlation effects of the 5
orbitals of Ir impurities, the SHA becomes positive with realistic correlation parameters and consistent with experiment. Moreover, our analysis shows that the DFT + HF approach is a convenient and general method to study the influence of local correlation effects on the spin Hall effect.
Gu, B.; Xu, Z.; 森 道康; Ziman, T.*; 前川 禎通
Journal of Applied Physics, 117(17), p.17D503_1 - 17D503_4, 2015/05
被引用回数：9 パーセンタイル：35.42(Physics, Applied)We find that the SHA can be dramatically enhanced by Bi impurities close to the Cu surface. The mechanisms of this enhancement are two-fold. One is that the localized impurity state on surface has a decreased hybridization and combined with Coulomb correlation effect. The other comes from the low-dimensional state of conduction electrons on surface, which results in a further enhancement of skew scattering by impurities. Furthermore, we note that a discrepancy in sign of SHA between the experiment and previous theories is simply caused by different definitions of SHA. This re-establishes skew scattering as the essential mechanism underlying the spin Hall effect in CuBi alloys.
Xu, Z.; Gu, B.; 森 道康; Ziman, T.*; 前川 禎通
Physical Review Letters, 114(1), p.017202_1 - 017202_5, 2015/01
被引用回数：20 パーセンタイル：72.33(Physics, Multidisciplinary)Recently a positive spin Hall angle (SHA) of 0.021, was observed experimentally in nonmagnetic CuIr alloys and attributed predominantly to an extrinsic skew scattering mechanism, while a negative SHA was obtained from ab initio calculations, using consistent definitions of the SHA. We reconsider the SHA in CuIr alloys, with the effects of the local electron correlation U in 5d orbitals of Ir impurities, included by the quantum Monte Carlo method. We found that the SHA is negative if we ignore such local electron correlation, but becomes positive once U approaches a realistic value. This may open up a way to control the sign of the SHA by manipulating the occupation number of impurities.
早野 明; 松川 瞬*; Xu, Z.*; 板倉 賢一*
Proceedings of 8th Asian Rock Mechanics Symposium (ARMS-8) (USB Flash Drive), 9 Pages, 2014/10
坑道壁面の地質観察は、亀裂性岩盤のモデル化に用いられる割れ目の幾何学的パラメータの設定に必要となるデータが取得できる調査のひとつである。しかしながら、高レベル放射性廃棄物の処分場建設時に行われる坑道壁面の地質観察は、数キロ四方にわたって展開される坑道群に対して行われることから、観察作業の効率化が必要である。また、地質専門家の経験や知識の違いから生じるデータの品質のばらつきを低減するために、客観的なデータ取得手法を用意することも必要である。これらの課題解決には、三次元レーザスキャナの活用が考えられる。本研究では、三次元レーザスキャナを適用した地質観察手法の整備の一環として、亀裂性岩盤のモデル化に必要となる割れ目の幾何学的データを明確にし、それらデータを三次元レーザスキャナデータから取得することを試みた。その結果、三次元レーザスキャナにより生成した傾斜図と傾斜方位図の目視判読により割れ目が抽出され、その割れ目のトレースマップと走向・傾斜が取得された。そして、地質専門家による観測結果と遜色のない割れ目のトレースマップと割れ目の走向・傾斜を取得することが可能であることが確認できた。
