Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Sueoka, Shigeru; Shimada, Koji; Ishimaru, Tsuneari; Danhara, Toru*; Iwano, Hideki*; Yagi, Koshi*
Chigaku Zasshi, 127(6), p.795 - 803, 2018/12
no abstracts in English
Aso, Tomokazu; Teshigawara, Makoto; Hasegawa, Shoichi; Muto, Hideki; Aoyagi, Katsuhiro; Nomura, Kazutaka; Takada, Hiroshi
Journal of Physics; Conference Series, 1021(1), p.012085_1 - 012085_4, 2018/06
Times Cited Count：0 Percentile：0.11(Nuclear Science & Technology)Aso, Tomokazu; Teshigawara, Makoto; Hasegawa, Shoichi; Aoyagi, Katsuhiro*; Muto, Hideki*; Nomura, Kazutaka*; Takada, Hiroshi; Ikeda, Yujiro
JAEA-Technology 2017-021, 75 Pages, 2017/08
JAEA-Technology-2017-021.pdf:33.03MB
Liquid hydrogen is employed as a cold neutron moderator material at the spallation neutron source of Materials and Life science experimental Facility of Japan Proton Accelerator Research Complex (J-PARC). From January 2015, it became observable that the differential pressure between heat exchangers and an 80 K adsorber (ADS) in a helium refrigerator system increased with operating time. In November 2015, the differential pressure rise became more significant, leading to degrade the refrigerating performance in cooling liquid hydrogen. In order to investigate the cause of the abnormal differential pressure rise between the heat exchangers and the ADS, we carried out visual inspection inside the heat exchangers and analyzed the impurities contained in the helium gas. Unfortunately, we could not identify the impurities causing the performance degradation, but observed a trace of oil in the inlet piping of the heat exchanger. Based on investigations of the abnormal events occurred in the refrigerators with similar refrigerating capacity at other facilities, we took measures that cleaning the heat exchangers with Freon and replacing the ADS with new one. As a result, the differential pressure rise phenomenon was removed to recover the performance. We have detected oil from the Freon used for cleaning the heat exchangers and at a felt supporting charcoal packed in the ADS. In particular, oil was accumulated in membranous form onto the felt at the entrance side in the ADS. The amount of oil contained in the helium gas was about 10 ppb or so, less than the design value, in the helium refrigerator. However, the oil accumulated onto the felt in the ADS through long operating period may cause abnormal differential pressure rise, leading to the performance degradation of the helium refrigerator. Further study is needed to specify the cause more clearly.
Sueoka, Shigeru; Umeda, Koji; Yasue, Kenichi; Niwa, Masakazu; Shimada, Koji; Ishimaru, Tsuneari; Danhara, Toru*; Iwano, Hideki*; Yagi, Koshi*
Chigaku Zasshi, 125(2), p.201 - 219, 2016/04
We applied multi-system thermochronology to the Tsuruga body of the Kojaku granite to constrain the cooling/denudation history of the Tsuruga area. Based on the thermochronometric results and other data, we reconstructed the cooling and denudation histories of the Tsuruga body as below: (1) the Tsuruga body intruded at c.a. 68 Ma at the depth of 4-5 km, (2) rapidly cooled down to c.a. 200
C by heat conduction within a few million years or less, and (3) slowly cooled due to peneplanation during the Cenozoic. This cooling/denudation history is consistent with the observations that cataclasite and fault gouge are dominant in the crush zones of the Tsuruga body, that similar slow cooling histories over the Cenozoic are estimated in the surrounding areas based on thermochronometric ages, and that the amount of denudation in the last few million years in the Tsuruga area is inferred at less than several hundred meters from the elevations of the uplifted peneplains.
-synuclein studied by quasielastic neutron scatteringFujiwara, Satoru; Araki, Katsuya*; Matsuo, Tatsuhito; Yagi, Hisashi*; Yamada, Takeshi*; Shibata, Kaoru; Mochizuki, Hideki*
PLOS ONE (Internet), 11(4), p.e0151447_1 - e0151447_17, 2016/04
Times Cited Count：24 Percentile：64.99(Multidisciplinary Sciences)Tatsumoto, Hideki; Aso, Tomokazu; Otsu, Kiichi; Kawakami, Yoshihiko; Aoyagi, Katsuhiro; Muto, Hideki
IOP Conference Series; Materials Science and Engineering, 101, p.012107_1 - 012107_8, 2015/12
Times Cited Count：0 Percentile：0.05(Thermodynamics)The Japan Proton Accelerator Research Complex (J-PARC) cryogenic hydrogen system was completed in April 2008. The proton beam power was gradually increased to 500 kW. A trial 600-kW proton beam operation was successfully completed in April 2015. We achieved long-lasting operation for more than three months. However, thus far, we encountered several problems such as unstable operation of the helium refrigerator because of some impurities, failure of a welded bellows of an accumulator, and hydrogen pump issues. Furthermore, the Great East Japan Earthquake was experienced during the cryogenic hydrogen system operation in March 2011. In this study, we describe the operation characteristics and our experiences with the J-PARC cryogenic hydrogen system.
=20 shell in 
Al investigated through the ground-state electric quadrupole momentShimada, Kenji*; Ueno, Hideki*; Neyens, G.*; Asahi, Koichiro*; Balabanski, D. L.*; Daugas, J. M.*; Depuydt, M.*; De Rydt, M.*; Gaudefroy, L.*; Gr
vy, S.*; et al.
Physics Letters B, 714(2-5), p.246 - 250, 2012/08
Times Cited Count：7 Percentile：41.35(Astronomy & Astrophysics)no abstracts in English
Awaji, Satoshi*; Namba, Masashi*; Watanabe, Kazuo*; Ito, Shun*; Aoyagi, Eiji*; Kai, Hideki*; Mukaida, Masashi*; Okayasu, Satoru
IEEE Transactions on Applied Superconductivity, 21(3), p.3192 - 3195, 2011/06
Times Cited Count：5 Percentile：33.75(Engineering, Electrical & Electronic)The flux pinning behaviors for the heavy ion irradiated Er123 films are investigated based on the detailed 
(
, 
, 
) properties. The double peaks of 
curves for //c appear in case of the matching field of 0.3 T along 
-axis and 1.7 T tilted from -axis. In addition, the peaks on () at = 0 (B//c), which originate from the columnar defects, decrease with increasing magnetic field but increase again near the irreversibility field. We found that the cooperation model of the -axis correlated and random pinning centers can describe the observed double peak behavior of (B) and the angular dependence of related to the correlated pinning.
-doped mixed scandium garnetsOkada, Hajime; Tanaka, Momoko; Kiriyama, Hiromitsu; Nakai, Yoshiki*; Ochi, Yoshihiro; Sugiyama, Akira; Daido, Hiroyuki; Kimura, Toyoaki*; Yanagitani, Takagimi*; Yagi, Hideki*; et al.
Optics Letters, 35(18), p.3048 - 3050, 2010/09
Times Cited Count：13 Percentile：53.86(Optics)Nakamura, Hiroo; Agostini, P.*; Ara, Kuniaki; Cevolani, S.*; Chida, Teruo*; Ciotti, M.*; Fukada, Satoshi*; Furuya, Kazuyuki*; Garin, P.*; Gessii, A.*; et al.
Fusion Engineering and Design, 83(7-9), p.1007 - 1014, 2008/12
Times Cited Count：19 Percentile：76.01(Nuclear Science & Technology)This paper describes the latest design of liquid lithium target system in IFMIF. Design requirement of the Li target is to provide a stable Li jet with a speed of 20 m/s to handle an averaged heat flux of 1 GW/m
. A double reducer nozzle and a concaved flow are applied to the target design. On Li purification, a cold trap and two kinds of hot trap are applied to control impurities below permissible levels. Nitrogen concentration shall be controlled below 10 wppm by one of the hot trap. Tritium concentration shall be controlled below 1 wppm by an yttrium hot trap. To maintain reliable continuous operation, various diagnostics are attached to the target assembly. Among the target assembly, a back-plate made of RAFM is located in the most severe region of neutron irradiation (50 dpa/y). Therefore, two design options of replaceable back wall and their remote handling systems are under investigation.
Yokoo, Kenji; Horiguchi, Hironori; Yagi, Masahiro; Nagadomi, Hideki; Yamamoto, Kazuyoshi; Sasajima, Fumio; Oyama, Koji; Ishikuro, Yasuhiro; Sasaki, Tsutomu; Hirane, Nobuhiko; et al.
JAEA-Technology 2007-018, 104 Pages, 2007/03
JAEA-Technology-2007-018.pdf:5.92MB
Reactor operation training using JRR-4 (Japan Research Reactor No.4) was started in FY 1969, one of the curriculums of Nuclear Technology and Education Center (NuTEC). After that, the program was updated and carried out for reactor operation training, control rod calibration, and measurement of various kind of characteristics. JRR-4 has been contributed for nuclear engineer training that is over 1,700 trainees from bother domestic and foreign countries. JRR-4 can be used for experiment from zero power to 3500kW, and the trainees can make experience to operate the reactor from start up to shut down, not only zero-power experiments (critical approach, control rod calibration, reactivity measurement, etc.) but also other experiments under high power operation (xenon effect, temperature effects, reactor power calibration, etc.). This report is based on various kinds of guidance texts using for training, and collected for operation and experiments for reactor physics.
Hirane, Nobuhiko; Ishikuro, Yasuhiro; Nagadomi, Hideki; Yokoo, Kenji; Horiguchi, Hironori; Nemoto, Takumi; Yamamoto, Kazuyoshi; Yagi, Masahiro; Arai, Nobuyoshi; Watanabe, Shukichi; et al.
JAEA-Technology 2006-028, 115 Pages, 2006/03
JAEA-Technology-2006-028.pdf:7.96MB
JRR-4, a light-water-moderated and cooled, swimming pool type research reactor using high-enriched uranium plate-type fuels had been operated from 1965 to 1996. In order to convert to low-enriched-uranium-silicied fuels, modification work had been carried out for 2 years, from 1996 to 1998. After the modification, start-up experiments were carried out to obtain characteristics of the low-enriched-uranium-silicied fuel core. The measured excess reactivity, reactor shutdown margin and the maximum reactivity addition rate satisfied the nuclear limitation of the safety report for licensing. It was confirmed that conversion to low-enriched-uranium-silicied fuels was carried out properly. Besides, the necessary data for reactor operation were obtained, such as nuclear, thermal hydraulic and reactor control characteristics. This report describes the results of start-up experiments and burnup experiments. The first criticality of low-enriched-uranium-silicied core was achieved on 14th July 1998, and the operation for joint-use has been carried out since 6th October 1998.
Tanaka, Hitoshi*; Takao, Masaru*; Matsushita, Tomohiro*; Aoyagi, Hideki*; Takeuchi, Masao*; Agui, Akane; Yoshigoe, Akitaka; Nakatani, Takeshi
Hoshako, 19(1), p.27 - 32, 2006/01
no abstracts in English
Nakatani, Takeshi; Agui, Akane; Yoshigoe, Akitaka; Tanaka, Hitoshi*; Takao, Masaru*; Takeuchi, Masao*; Matsushita, Tomohiro*; Aoyagi, Hideki*
JAERI-Tech 2005-027, 29 Pages, 2005/05
JAERI-Tech-2005-027.pdf:5.14MB
We measured the orbit fluctuation caused by APPLE-2 type undulator (ID23) installed in the SPring-8 storage ring by using the developed real time measurement system of electron and photon beam position monitors. We quantitatively found two characteristic fluctuations correlating with the ID23 motion by wavelet transform which is a kind of frequency analysis. One originates from the variation of error field during the ID drive. The other originates from the stray magnetic field leaked from the servomotors for the phase drive. Using these results, we tried to get rid of the effect of error fields on the beam orbit by the precise feed-forward correction table and the stray field shield. Consequently we succeeded in suppressing the orbit fluctuation down to sub-micron during the gap drive, which is observed by photon beam position monitors installed in downstream 20m from each light source point.
Nakatani, Takeshi; Agui, Akane; Yoshigoe, Akitaka; Matsushita, Tomohiro*; Takao, Masaru*; Takeuchi, Masao*; Aoyagi, Hideki*; Tanaka, Hitoshi*
JAERI-Tech 2004-013, 16 Pages, 2004/12
JAERI-Tech-2004-013.pdf:3.55MB
We observed two characteristic electron orbit fluctuations caused when the phase of ID23 (APPLE-2 type undulator) installed at SPring-8 was driven. One was caused by the variation of magnetic error filed of ID23 when the phase was driven. The other was caused by the noise from the phase drive system which adoped AC servomotors. We measured these orbit fluctuations synchronized with the phase motion using the real-time electron beam position measurement system. The part of the orbit fluctuation was supressed by the correction table which was made referring to the obtained data.
Nakatani, Takeshi; Agui, Akane; Yoshigoe, Akitaka; Matsushita, Tomohiro*; Takao, Masaru*; Aoyagi, Hideki*; Takeuchi, Masao*; Tanaka, Hitoshi*
AIP Conference Proceedings 705, p.290 - 293, 2004/00
We have developed a new method to extract only the orbit fluctuation caused by changing magnetic field error of an insertion device (ID). This method consists of two main parts. (i) The orbit fluctuation is measured with modulating the error field of the ID by using the real-time beam position measuring system. (ii) The orbit fluctuation depending on the variation of the error field of the ID is extracted by the filter applying the Wavelet Transform. We call this approach the amplitude modulation method. This analysis technique was applied to measure the orbit fluctuation caused by the error field of APPLE-2 type undulator (ID23) installed in the SPring-8 storage ring. We quantitatively measured two kinds of the orbit fluctuation which are the static term caused by the magnetic field error and the dynamic term caused by the eddy current on the ID23 chamber.
Matsushita, Tomohiro*; Agui, Akane; Yoshigoe, Akitaka; Takao, Masaru*; Aoyagi, Hideki*; Takeuchi, Masao*; Nakatani, Takeshi; Tanaka, Hitoshi*
AIP Conference Proceedings 705, p.21 - 24, 2004/00
no abstracts in English
Agui, Akane; Aoyagi, Hideki*; Yoshigoe, Akitaka; Nakatani, Takeshi
JAERI-Tech 2003-089, 23 Pages, 2003/12
JAERI-Tech-2003-089.pdf:1.33MB
no abstracts in English
Nakatani, Takeshi; Tanaka, Hitoshi*; Takao, Masaru*; Agui, Akane; Yoshigoe, Akitaka; Takeuchi, Masao*; Aoyagi, Hideki*; Okuma, Haruo*
JAERI-Tech 2003-048, 29 Pages, 2003/05
JAERI-Tech-2003-048.pdf:1.14MB
no abstracts in English
Matsushita, Tomohiro*; Agui, Akane; Yoshigoe, Akitaka; Nakatani, Takeshi; Tanaka, Hitoshi*; Takao, Masaru*; Aoyagi, Hideki*; Takeuchi, Masao*
Hoshako, 15(5), p.303 - 307, 2002/05
no abstracts in English
