Probing deformation behavior of a refractory high-entropy alloy using neutron diffraction

Zhou, Y.*; Song, W.*; Zhang, F.*; Wu, Y.*; Lei, Z.*; Jiao, M.*; Zhang, X.*; Dong, J.*; Zhang, Y.*; Yang, M.*; et al.

Journal of Alloys and Compounds, 971, p.172635_1 - 172635_7, 2024/01

https://doi.org/10.1016/j.jallcom.2023.172635

The grain orientation-dependent lattice strain evolution of a (TiZrHfNb) refractory high-entropy alloy (HEA) during tensile loading has been investigated using neutron diffraction. The equivalent strain-hardening rate of each of the primary -oriented grain families was found to be relatively low, manifesting the macroscopically weak work-hardening ability of such a body-centered cubic (BCC)-structured HEA. This finding is indicative of a dislocation planar slip mode that is confined in a few single-slip planes and leads to in-plane softening by high pile-up stresses.

A Large-scale particle-based simulation of heat and mass transfer behavior in EAGLE ID1 in-pile test

Zhang, T.*; Yao, Y.*; 守田 幸路*; Liu, X.*; Liu, W.*; 今泉 悠也; 神山 健司

Proceedings of 30th International Conference on Nuclear Engineering (ICONE30) (Internet), 9 Pages, 2023/05

The in-pile EAGLE ID1 test was conducted by Japan Atomic Energy Agency to demonstrate the effectiveness of the fuel assembly with an internal duct structure during a core disruptive accident in a sodium-cooled fast reactor. In this study, a new computational fluid dynamics code based on the fully Lagrangian particle method was developed for the purpose of clarifying the failure mechanism of the inner duct wall of FAIDUS. The three-dimensional simulation of the ID1 test was performed to analyze a series of thermal hydraulic behaviors leading up to duct wall failure for a computational domain that included six fuel pins. The simulations reasonably reproduced the heat transfer characteristics observed in the test, showing that the local contact of liquid steel with high thermal conductivity with the duct wall greatly enhances the heat transfer from the nuclear heating fuel to the duct wall. The results support the validity of the conclusions of our analytical study regarding the molten pool-to-duct wall heat transfer mechanism that caused the thermal failure of the duct wall.

Tensile overload-induced texture effects on the fatigue resistance of a CoCrFeMnNi high-entropy alloy

Lam, T.-N.*; Chin, H.-H.*; Zhang, X.*; Feng, R.*; Wang, H.*; Chiang, C.-Y.*; Lee, S. Y.*; 川崎 卓郎; Harjo, S.; Liaw, P. K.*; et al.

Acta Materialia, 245, p.118585_1 - 118585_9, 2023/02

https://doi.org/10.1016/j.actamat.2022.118585

The present study investigates the crystallographic-texture effects on the improved fatigue resistance in the CoCrFeMnNi high-entropy alloys (HEAs) with the full-size geometry of the ASTM Standards E647-99. We exploited X-ray nano-diffraction mapping to characterize the crystal-deformation levels ahead of the crack tip after stress unloading under both constant- and tensile overloaded-fatigue conditions. The crack-tip blunting-induced much higher deformation level was concentrated surrounding the crack-tip which delays the fatigue-crack growth immediately after a tensile overload. The predominant deformation texture orientation in the Paris regime was investigated, using electron backscatter diffraction and orientation distribution function analyses. The twinning formation-driven shear deformation gave rise to the development of the Goss-type texture within the plastic deformation regime under a tensile-overloaded-fatigue condition, which was attributed to enhance the crack deflection and thus the tensile induced crack-growth-retardation period in the CoCrFeMnNi HEA.

Ten years of warming increased plant-derived carbon accumulation in an East Asian monsoon forest

Zhang, J.*; Kuang, L.*; Mou, Z.*; 近藤 俊明*; 小嵐 淳; 安藤 麻里子; Li, Y.*; Tang, X.*; Wang, Y.-P.*; Peuelas, J.*; et al.

Plant and Soil, 481(1-2), p.349 - 365, 2022/12

https://doi.org/10.1007/s11104-022-05642-8

Soil warming effects on soil organic carbon (SOC) decomposition and stabilization are highly variable, and the underlying mechanisms are poorly understood. In this study, concentration, stability (dissolved, particle and mineral-associated SOC), and source (plant-derived and microbial-derived) of SOC, soil microbial community composition, and enzyme activities were studied in a 10-year soil warming field experiment in an East Asian monsoon forest. The results showed that 10-year soil warming significantly enhanced SOC in the top 0-10 cm soil. The increased SOC induced by warming was mainly derived from plants with lignin markers, accompanied by a decrease in microbial-derived SOC. This highlights an urgent need for a better understanding of how the contrasting effects of plant- and microbial-derived C mediate the response of the SOC pool to warming across different biomes.

Strain hardening behavior of additively manufactured and annealed AlSi3.5Mg2.5 alloy

Zhang, X. X.*; Lutz, A.*; Andr, H.*; Lahres, M.*; Gong, W.; Harjo, S.; Emmelmann, C.*

Journal of Alloys and Compounds, 898, p.162890_1 - 162890_8, 2022/03

https://doi.org/10.1016/j.jallcom.2021.162890

The ductility of the Al alloys produced by additive manufacturing (AM) has become a critical property, as the AM Al alloys are increasingly used in the automotive industry. However, the ductility of as-built AM Al alloys is relatively low, even with optimized AM conditions. The post-annealing treatment provides an efficient way to improve ductility. Previous investigation has shown that the annealed AM AlSi3.5Mg2.5 alloy possesses superior ductility. However, the plastic deformation micro-mechanisms of the annealed AM AlSi3.5Mg2.5 alloy remain unclear. In this study, in-situ neutron diffraction was employed to explore the annealed AM AlSi3.5Mg2.5 alloy. The evolutions of phase stresses, dislocation density, and crystallite size in the annealed AM AlSi3.5Mg2.5 alloy during tensile deformation were analyzed. The experimental investigation reveals that the dislocation density in the Al matrix of the annealed AM AlSi3.5Mg2.5 alloy increases slowly in the early plastic deformation stage, and it reaches a saturated level upon the following uniform deformation. The crystallite size decreases quickly in the early deformation stage, and then it decreases slowly. The Kocks-Mecking model and the Voce model can capture the strain hardening behavior well. The determined physical constitutive equations can be applied in continuum mechanical computer simulations.

Long decay length of magnon-polarons in BiFeO/LaSrMnO heterostructures

Zhang, J.*; Chen, M.*; Chen, J.*; 山本 慧; Wang, H.*; Hamdi, M.*; Sun, Y.*; Wagner, K.*; He, W.*; Zhang, Y.*; et al.

Nature Communications (Internet), 12, p.7258_1 - 7258_8, 2021/12

https://doi.org/10.1038/s41467-021-27405-2

Magnons can transfer information in metals and insulators without Joule heating, and therefore are promising for low-power computation. The on-chip magnonics however suffers from high losses due to limited magnon decay length. In metallic thin films, it is typically on the tens of micrometre length scale. Here, we demonstrate an ultra-long magnon decay length of up to one millimetre in multiferroic/ferromagnetic BiFeO(BFO)/LaSrMnO (LSMO) heterostructures at room temperature. This decay length is attributed to a magnon-phonon hybridization and is more than two orders of magnitude longer than that of bare metallic LSMO. The long-distance modes have high group velocities of 2.5 km as detected by time-resolved Brillouin light scattering. Numerical simulations suggest that magnetoelastic coupling via the BFO/LSMO interface hybridizes phonons in BFO with magnons in LSMO. Our results provide a solution to the long-standing issue on magnon decay lengths in metallic magnets and advance the bourgeoning field of hybrid magnonics.

Field-tuned magnetic structure and phase diagram of the honeycomb magnet YbCl

Hao, Y. Q.*; Wo, H. L.*; Gu, Y. M.*; Zhang, X. W.*; Gu, Y. Q.*; Zheng, S. Y.*; Zhao, Y.*; Xu, G. Y.*; Lynn, J. W.*; 中島 健次; et al.

Science China; Physics, Mechanics & Astronomy, 64(3), p.237411_1 - 237411_6, 2021/03

https://doi.org/10.1007/s11433-020-1626-3

We report thermodynamic and neutron diffraction measurements on the magnetic ordering properties of the honeycomb lattice magnet YbCl. We find YbCl exhibits a Nel type long-range magnetic order at the wavevector (0, 0, 0) below T = 600 mK. This magnetic order is associated with a small sharp peak in heat capacity and most magnetic entropy release occurs above the magnetic ordering temperature. The magnetic moment lies in-plane, parallel to the monoclinic a-axis, whose magnitude m = 0.86(3) is considerably smaller than the expected fully ordered moment of 2.24 for the doublet crystal-field ground state. The magnetic ordering moment gradually increases with increasing magnetic field perpendicular to the ab-plane, reaching a maximum value of 1.6(2) at 4 T, before it is completely suppressed above 9 T. These results indicate the presence of strong quantum fluctuations in YbCl.

Stacking fault driven phase transformation in CrCoNi medium entropy alloy

He, H.*; Naeem, M.*; Zhang, F.*; Zhao, Y.*; Harjo, S.; 川崎 卓郎; Wang, B.*; Wu, X.*; Lan, S.*; Wu, Z.*; et al.

Nano Letters, 21(3), p.1419 - 1426, 2021/02

https://doi.org/10.1021/acs.nanolett.0c04244

In CrCoNi, a so-called medium-entropy alloy, an fcc-to-hcp phase transformation has long been anticipated. Here, we report an in situ loading study with neutron diffraction, which revealed a bulk fcc-to-hcp phase transformation in CrCoNi at 15 K under tensile loading. By correlating deformation characteristics of the fcc phase with the development of the hcp phase, it is shown that the nucleation of the hcp phase was triggered by intrinsic stacking faults. The confirmation of a bulk phase transformation adds to the myriads of deformation mechanisms available in CrCoNi, which together underpin the unusually large ductility at low temperatures.

Quantifying internal strains, stresses, and dislocation density in additively manufactured AlSi10Mg during loading-unloading-reloading deformation

Zhang, X. X.*; Andr, H.*; Harjo, S.; Gong, W.*; 川崎 卓郎; Lutz, A.*; Lahres, M.*

Materials & Design, 198, p.109339_1 - 109339_9, 2021/01

https://doi.org/10.1016/j.matdes.2020.109339

Here, in-situ neutron diffraction is employed to explore the residual strains, stresses, and dislocation density in the LPBF AlSi10Mg during loading-unloading-reloading deformation. It is found that the maximum residual stresses of the Al and Si phases in the loading direction reach up to about -115 (compressive) and 832 (tensile) MPa, respectively. A notable dislocation annihilation phenomenon is observed in the Al matrix: the dislocation density decreases significantly during unloading stages, and the amplitude of this reduction increases after experiencing a larger plastic deformation. At the macroscale, this dislocation annihilation phenomenon is associated with the reverse strain after unloading. At the microscale, the annihilation phenomenon is driven by the compressive residual stress in the Al matrix. Meanwhile, the annihilation of screw dislocations during unloading stages contributes to the reduction in total dislocation density.

Comparison of heavy-ion transport simulations; Collision integral with pions and resonances in a box

小野 章*; Xu, J.*; Colonna, M.*; Danielewicz, P.*; Ko, C. M.*; Tsang, M. B.*; Wang, Y,-J.*; Wolter, H.*; Zhang, Y.-X.*; Chen, L.-W.*; et al.

Physical Review C, 100(4), p.044617_1 - 044617_35, 2019/10

AA2019-0025.pdf:2.76MB

https://doi.org/10.1103/PhysRevC.100.044617

2017年4月に開催された国際会議Transport2017において、重イオン核反応モデルの国際的な比較が議論された。重イオン加速器の安全評価や宇宙飛行士の被ばく評価等で重要な役割を果たすため、世界中で重イオン核反応の様々な理論モデルが開発されている。本研究では、辺の長さが20fmの直方体に320個の中性子と陽子をランダム配置し、それらが70fm/cの間に起こす散乱の回数やエネルギーを計算した。ここでは、特にパイオンやその前駆体であるデルタ共鳴の生成に注目して比較を行った。参加コードは、個々の粒子の時間発展を追うQMD型コードと、粒子の位置や運動量の確率分布を決めておき、散乱や崩壊が発生したときそれらを乱数サンプリングするBUU型コードがあり、発表者が用いたJQMDは前者に属する。本研究により、計算における時間刻みが各コードによる結果の差の主な原因であることが分かった。さらに、今後のJQMDの改良方針の策定に有益な知見を得ることができた。