Stabilization processing of hazardous and radioactive liquid wastes derived from advanced aqueous separation experiments for safety handling and management of waste

Nakahara, Masaumi; Watanabe, So; Ogi, Hiromichi*; Arai, Yoichi; Aihara, Haruka; Motoyama, Risa; Shibata, Atsuhiro; Nomura, Kazunori; Kajinami, Akihiko*

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.66 - 70, 2019/09

A wide variety of hazardous and radioactive liquid waste has generated derived from an advanced aqueous separation experiments in the Chemical Processing Facility. Therefore, they should be stabilized for the safety handling and management. In this study, we report a precipitation or an oxidation for hazardous materials, a solvent extraction for recovery of nuclear materials, and a concentration of solution by a freeze-drying method.

Study on eutectic melting behavior of control rod materials in core disruptive accidents of sodium-cooled fast reactors, 1; Project overview

Yamano, Hidemasa; Takai, Toshihide; Furukawa, Tomohiro; Kikuchi, Shin; Emura, Yuki; Kamiyama, Kenji; Fukuyama, Hiroyuki*; Higashi, Hideo*; Nishi, Tsuyoshi*; Ota, Hiromichi*; et al.

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.418 - 427, 2019/09

Eutectic reactions between boron carbide (BC) and stainless steel (SS) as well as its relocation are one of the key issues in a core disruptive accident (CDA) evaluation in sodium-cooled fast reactors. Since such behaviors have never been simulated in CDA numerical analyses, it is necessary to develop a physical model and incorporate the model into the CDA analysis code. This study is focusing on BC-SS eutectic melting experiments, thermophysical property measurement of the eutectic melt, and physical model development for the eutectic melting reaction. The eutectic experiments involve the visualization experiments, eutectic reaction rate experiments and material analyses. The thermophysical properties are measured in the range from solid to liquid state. The physical model is developed for a severe accident computer code based on the measured data of the eutectic reaction rate and the physical properties. This paper describes the project overview and progress of experimental and analytical studies by 2017. Specific results in this paper is boron concentration distributions of solidified BC-SS eutectic sample in the eutectic melting experiments, which would be used for the validation of the eutectic physical model implemented into the computer code.

Behavior of lanthanides and actinides for their mutual separation using extractant and masking agent

Sasaki, Yuji; Morita, Keisuke; Matsumiya, Masahiko*; Nakase, Masahiko*

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.108 - 112, 2019/09

We attempted to separate An from Ln, and Am and Cm by the system including extractant and masking agent. The separation factor of Nd and Am was approximately 10 by TODGA-DTPA-BA and that of Am and Cm was over 3 by TODGA-DOODA(C2). Using these batch data, profiles of metal concentration with multi-step extractions proposed in this manuscript were demonstrated.

Study on eutectic melting behavior of control rod materials in core disruptive accidents of sodium-cooled fast reactors, 4; Effect of BC addition on viscosity of austenitic stainless steel in liquid state

Ota, Hiromichi*; Kokubo, Hiroki*; Nishi, Tsuyoshi*; Yamano, Hidemasa

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.858 - 860, 2019/09

A viscosity measurement apparatus has been developed. It is known that the measurement of the viscosity of molten alloy at elevated temperatures is difficult due to the difficulty of handling for low viscosity fluids such as the stainless steel (SS)+BC alloy. In this study, the viscosities of the molten nickel (Ni) and stainless steel (SS) were measured by the oscillating crucible method to confirm the performance of the viscosity measurement apparatus as a first step. This method is suitable for high temperature molten alloys. A crucible containing molten metal is suspended, and a rotational oscillation is given to the crucible electromagnetically. The oscillation was damped by the friction of molten metal. The viscosity is determined from the period of oscillation and the logarithmic decrement. The crucible was connected to a mirror block and an inertia disk made of aluminum, and whole of them was suspended by a wire made of platinum-13% rhodium alloy. A laser light is irradiated to the mirror. The reflection light is detected by the photo-detectors, and then, the logarithmic decrement of molten metal is determined. The viscosities of molten nickel and SS melts were measured up to 1823 K. In these results, the measured viscosity values of molten Ni and SS were close to those of the literature values of molten Ni and SS. By the equipment, the viscosity of molten SS+BC alloys are measured. The BC concentration dependence of the viscosity of molten SS+BC alloys is to be clarified.

Study on eutectic melting behavior of control rod materials in core disruptive accidents of sodium-cooled fast reactors, 5; Validation of a multi-phase model for eutectic reaction between molten stainless steel and BC

Liu, X.*; Morita, Koji*; Yamano, Hidemasa

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.47 - 51, 2019/09

Investigation of the eutectic reaction in a core disruptive accident of sodium cooled reactor is of importance since reactor criticality will be affected by the change in reactivity after eutectic reaction. In this study, we performed 1st step of validation analysis using a fast reactor safety analysis code, SIMMER-III, with the developed model based on a new series of experiments, where a BC pellet was immersed into a molten stainless steel (SS) pool. The simulation results showed the general behavior of eutectic material formation measured in the experiments reasonably. The eutectic reaction consumes solid BC and liquid SS, and then the liquid eutectic composition is produced at the early stage of reaction due to the high temperature of molten SS. Movement of the eutectic material in the molten pool leads to the redistribution of boron element. Molten SS pool then freezes to solid SS and movement of eutectic material is stopped by surrounding solid SS. Boron concentration in the pool was measured after molten SS freezes into a solid. Simulation results indicate that boron tends to accumulate in the upper part of the molten pool. This is attributed to the buoyancy force acting on lighter boron in the molten SS pool. A parametric study was also conducted by changing the initial temperature of BC pellet and SS to investigate the temperature sensitivity on the eutectic reaction behavior.

Behavior of high-burnup advanced LWR fuel cladding tubes under LOCA conditions

Narukawa, Takafumi; Amaya, Masaki

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.912 - 921, 2019/09

Technological development of the particle size adjustment of dry recovered powder

Segawa, Tomoomi; Yamamoto, Kazuya; Makino, Takayoshi; Iso, Hidetoshi; Kawaguchi, Koichi; Ishii, Katsunori; Sato, Hisato; Fukasawa, Tomonori*; Fukui, Kunihiro*

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.738 - 745, 2019/09

In the MOX fuel fabrication process, the dry grinding technology of mixed oxide pellets have been developed for the effective use of nuclear fuel materials. To develop a technology to control the particle size of dry recovered powder, the performance of the buhrstone mill and the collision plate type jet mill were studied using a simulated powder of particle size distribution about 500 m. We found that the particle size can be controlled at the range of about 250 m or less by both by adjusting the clearance between the grinding wheels of the buhrstone mill, and the clearance and elevation angle of the clarification zone of the collision plate type jet mill. And furthermore, the collision plate type jet mill is considered to be suitable for particle size control because the operating parameters of the classifier can be finely adjusted.

Zr separation from high-level liquid waste with a novel hydroxyacetoamide type extractant

Morita, Keisuke; Suzuki, Hideya; Matsumura, Tatsuro; Takahashi, Yuya*; Omori, Takashi*; Kaneko, Masaaki*; Asano, Kazuhito*

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.464 - 468, 2019/09

High level liquid waste (HLLW) contains several radionuclides with half-lives longer than 10 year. For reduce environmental burden of waste disposal, minor actinoids and long-lived fission products will to be partitioned and transmuted. JAEA and Toshiba developed process for recovering Se, Zr, Pd and Cs from HLLW. Solvent extraction for Zr with novel extractant, -didodecyl-2-hydroxyacetoamide (HAA) was detailed. The HAA system showed high selectivity for Zr, as indicated by the extraction order of Zr Mo Pd Ag Sb Sn Lns Fe. The extracted species was determined as Zr(HAA)(NO)(HNO). A continuous countercurrent extraction with HAA was applied to a simulated, concentrated HLLW after Pd, Se, and Cs removal, where the quantitative extraction of Zr and Mo was effectively demonstrated.

Study on eutectic melting behavior of control rod materials in core disruptive accidents of sodium-cooled fast reactor, 2; Effect of BC addition on thermophysical properties of austenitic stainless steel in a solid state

Takai, Toshihide; Furukawa, Tomohiro; Yamano, Hidemasa

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.847 - 852, 2019/09

Research and development of ZrC-coated UO particle fuel in Japan Atomic Energy Research Institute

; Ikawa, Katsuichi; ; ; Iwamoto, K.

Nuclear Fuel Performance, p.163 - 169, 1985/00

no abstracts in English