Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Fukuta, Shimpei; Sawabe, Yuki; Suzuki, Takahiro*; Ishiyama, Tatsuya*; Kawase, Masato*; Ito, Yuichi; Kato, Yuko; Yoshii, Akinobu; Kikuzawa, Nobuhiro; Ouchi, Nobuo
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1122 - 1125, 2014/06
The installation of Cs-seeded RF-driven H
ion source (RF ion source) to J-PARC LINAC is scheduled in 2014. Similarly the replacement of RFQ III from RFQ is scheduled in 2014. The test stand of the cooperation of RF ion source & RFQ III is being made in the J-PARC LINAC building for the beam acceleration examination now. The J-PARC control group designed test stand control system by thinking that test stand control system had to be equal to J-PARC accelerator control system. Specifically, Introduction of MPS for protect an apparatus. Implementation of EPICS environment for remotely controlling the equipment. It is construction of the timing system for sending a timing signal to each accelerator component device. This report describes construction of the control system in a test stand.
Sawamura, Masaru; Nagai, Ryoji; Nishimori, Nobuyuki; Hajima, Ryoichi
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.956 - 959, 2014/06
no abstracts in English
Shinoe, Kenji*; Sakai, Hiroshi*; Umemori, Kensei*; Enami, Kazuhiro*; Sato, Masato*; Furuya, Takaaki*; Sawamura, Masaru; Cenni, E.*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.950 - 952, 2014/06
no abstracts in English
Takeuchi, Yasunao*; Sawamura, Masaru
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.597 - 601, 2014/06
no abstracts in English
Sato, Masato*; Umemori, Kensei*; Enami, Kazuhiro*; Sakai, Hiroshi*; Shinoe, Kenji*; Furuya, Takaaki*; Sawamura, Masaru; Cenni, E.*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.973 - 976, 2014/06
no abstracts in English
Sakai, Hiroshi*; Umemori, Kensei*; Enami, Kazuhiro*; Sato, Masato*; Shinoe, Kenji*; Furuya, Takaaki*; Sawamura, Masaru; Cenni, E.*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.212 - 216, 2014/06
no abstracts in English
Okoshi, Kiyonori; Ikegami, Kiyoshi*; Koizumi, Isao; Ueno, Akira; Takagi, Akira*; Yamazaki, Saishun; Oguri, Hidetomo
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.946 - 949, 2014/06
A J-PARC ion source driven with a LaB6 filament is being operated without any serious trouble since the restoration from the earthquake. The H ion current from the source is routinely restricted 19 mA for the filament lifetime. In order to increase the beam power at the linac beam operation, the beam current from the ion source was increased to 22 mA. At this operation, the filament lifetime was estimated by the reduction in the filament current. According to the steep reduction in the filament current, the break of the filament was predicted. Although the filament has broken after 10 h from the steep current reduction, the beam operation was restarted 8 h later by the preparation for the exchange of new filament. At the study time for the 3 GeV synchrotron, the ion source was operated at 30 mA for 8 days.
Maebara, Sunao; Antonio, P.*; Ichikawa, Masahiro; Takahashi, Hiroki; Suzuki, Hiromitsu; Sugimoto, Masayoshi
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.561 - 563, 2014/06
no abstracts in English
Yuri, Yosuke; Yuyama, Takahiro; Ishizaka, Tomohisa; Yoshida, Kenichi; Ishibori, Ikuo; Okumura, Susumu
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.138 - 142, 2014/06
no abstracts in English
Miyawaki, Nobumasa; Fukuda, Mitsuhiro*; Kurashima, Satoshi; Kashiwagi, Hirotsugu; Okumura, Susumu; Arakawa, Kazuo*; Kamiya, Tomihiro
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.500 - 502, 2014/06
no abstracts in English
Enami, Kazuhiro*; Furuya, Takaaki*; Sakai, Hiroshi*; Sato, Masato*; Shinoe, Kenji*; Umemori, Kensei*; Sawamura, Masaru; Cenni, E.*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.602 - 604, 2014/06
no abstracts in English
Harada, Hiroyuki; Meigo, Shinichiro; Shirakata, Masashi*; Sato, Yoichi*; Tamura, Fumihiko; Tejima, Masaki*; Hashimoto, Yoshinori*; Igarashi, Susumu*; Koseki, Tadashi
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.39 - 43, 2014/06
The J-PARC 3-50 BT line is the beam transport line of extracted beam from 3-GeV rapid-cycling synchrotron (RCS) to 50-GeV main ring (MR). The RCS is the high-intensity proton accelerator, which designed beam power is 1 MW, and has the complex source of space charge effect, etc. Therefore, the uncontrolled emittance growth and beam halo increase nonlinearly with the increasing the beam power. Additionally, physical aperture of MR with 81 
mm mrad is smaller than that of RCS with 486 mm mrad. Therefore, the 3-50 BT line has the collimators in order to scrape the tail/halo of extracted beam from the RCS. The designed collimator aperture is 54 mm mrad. It is required to measure and optimize the optics parameter in the collimator area for taking full advantage of beam collimation. This paper will introduce the method of optics measurement and report the result of the measurement and optimization based on the simulation.
Hatakeyama, Shuichiro; Yoshimoto, Masahiro
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1082 - 1084, 2014/06
In J-PARC RCS (Rapid Cycling Synchrotron), in order to perform transverse orbit matching of the injection beam, it is used a total of 7 sets of multi-wire profile monitors (MWPMs). It is considered that beam loss around the equipments of injection beam line will be increased significantly because it is planed the beam power from the LINAC will be enforced in this fiscal year. So we will install a new MWPM on the H0 dump line to measure the injection orbit more precicely. In this time, we have developed a new data acquisition system using multi-channel digitizer. As the feature, it is improved the S/N ratio as compared with the present system using a multiplexer. Also the cost of the new system is estimated to be lower than the present system. In this report it is described the performance of the new DAQ system by using real beam with the existing MWPM2.
Hori, Toshihiko; Sato, Fumiaki; Shinozaki, Shinichi; Chishiro, Etsuji; Oguri, Hidetomo; Futatsukawa, Kenta*; Fukui, Yuji*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1001 - 1003, 2014/06
no abstracts in English
Watanabe, Yasuhiro; Tani, Norio; Inoue, Keigo*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.628 - 631, 2014/06
no abstracts in English
Kawamura, Masato*; Chishiro, Etsuji; Hori, Toshihiko; Shinozaki, Shinichi; Sato, Fumiaki; Fukui, Yuji*; Futatsukawa, Kenta*; Yamazaki, Masayoshi*; Sagawa, Ryu*; Miyajima, Noriyuki*; et al.
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.605 - 607, 2014/06
This report describes the present status of the klystron power supply systems for the J-PARC linac. The systems for the 181 MeV linac were operated from September to May. A few breakdowns were occurred, and are described in this report. The new systems for the upgrade of the linac from 181MeV to 400 MeV have been installed until now, and the 3 HVDCPSs and the 3 anode modulators of the new systems have been operated. All the systems for 400 MeV linac will be operated in this autumn.
Jimbo, Koichi*; Soda, Hikaru*; Nakao, Masao*; Yuri, Yosuke; Tongu, Hiromu*; Noda, Akira*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1057 - 1059, 2014/06
Tobita, Norimitsu; Yoshimoto, Masahiro; Yamazaki, Yoshio; Saeki, Riuji; Okabe, Kota; Kinsho, Michikazu; Takeda, Osamu*; Muto, Masayoshi*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.915 - 919, 2014/06
The charge conversion foil used with a J-PARC 3GeV synchrotron (RCS: Rapid Cycling Synchrotron) is a thin film made from carbon about 1 micrometer thick, and it radioactivates it by continuing being irradiated with a beam. Moreover, generally it is thought that degradation progresses and foil itself breaks easily. However, when dealing with the foil after irradiation, the measure against the danger of the contamination and the contamination in the living body by foil dispersing is one of the subjects. So, in RCS, the foil exchange booth for collecting the radioactivated foil safely and certainly was installed. Even when dispersing foil temporarily, the radioactivated foil can be shut up only in Booth and a worker's contamination and contamination of work area could be prevented. Moreover, when it sees from a viewpoint of the performance gain of foil, analysis and observation of the collected foil are one of the important issues. Then, in order to observe the radioactivated foil after beam irradiation, the transparent protective case which can be sealed with a foil frame simple substance was developed. In this announcement, the equipment developed in order to collect the charge conversion foil after beam irradiation, and the established technique are announced in detail.
Saeki, Riuji; Yoshimoto, Masahiro; Yamazaki, Yoshio; Tobita, Norimitsu; Okabe, Kota; Kinsho, Michikazu; Takeda, Osamu*; Muto, Masayoshi*
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.523 - 526, 2014/06
RCS has loaded with the foil of 15 sheets including a reserve into equipment so that it can exchange in a short time, when foil is damaged also in a beam operating period. It is difficult for foil to be made of a thin film about 1 micrometer thick, and to treat as it is. Then, foil is fixed to the frame which stuck the SiC fiber, and foil is not touched, but only a frame is held, and it enabled it to operate it. The following preparations are needed as new foil exchange work. (1) Exfoliation and recovery of foil which have been vapor-deposited to glass substrate. (2) Dryness and logging of exfoliative foil. (3) Preparation of SiC wire, and attachment on frame. (4) Fix foil to a frame. (5) Although charge on a magazine-rack was performed manually altogether until now, there were many work man days, and the quality of the prepared foil had variation. Then, equipment required in order to secure reproducibility was developed. The technique for working efficiently simultaneously was established. In this announcement, the technique established until now and the developed jigs are announced in detail.
Nishimori, Nobuyuki; Nagai, Ryoji; Matsuba, Shunya; Hajima, Ryoichi; Yamamoto, Masahiro*; Miyajima, Tsukasa*; Honda, Yosuke*; Uchiyama, Takashi*; Iijima, Hokuto*; Kuriki, Masao*; et al.
Proceedings of 10th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.174 - 178, 2014/06
no abstracts in English
