Takahashi, Osamu*; Shibui, Yohei*; Xu, P. G.; Harjo, S.; Suzuki, Tetsuya*; Tomota, Yo*
Quantum Beam Science (Internet), 4(1), p.16_1 - 16_15, 2020/03
Kumada, Takayuki; Oba, Yojiro; Motokawa, Ryuhei; Morooka, Satoshi; Tominaga, Aki; Tanida, Hajime; Shobu, Takahisa; Konno, Azusa; Owada, Kenji*; Ono, Naoko*; et al.
Journal of Nuclear Materials, 528, p.151890_1 - 151890_7, 2020/01
We have developed an anomalous small-angle X-ray scattering (ASAXS) diffractometer in SPring-8 to investigate irradiation-induced nanostructural change in ion-beam irradiated stainless steel. A thermally-aged MA956 stainless steel sample displays power-law scattering that follows the Porod law at the magnitude of scattering vector, Q, below 0.5 nm and an overlapped shoulder around 0.7 nm. After the ion-beam irradiation, the intensity of the shoulder remained unchanged, whereas that of the power-law scattering nearly doubled. This result indicates that none of the structural parameters of the Cr-rich nanoprecipitates, such as the number density, size, and interface roughness, were changed by the irradiation.
Ota, Hiromichi*; Kokubo, Hiroki*; Nishi, Tsuyoshi*; Yamano, Hidemasa
Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.858 - 860, 2019/09
A viscosity measurement apparatus has been developed. It is known that the measurement of the viscosity of molten alloy at elevated temperatures is difficult due to the difficulty of handling for low viscosity fluids such as the stainless steel (SS)+BC alloy. In this study, the viscosities of the molten nickel (Ni) and stainless steel (SS) were measured by the oscillating crucible method to confirm the performance of the viscosity measurement apparatus as a first step. This method is suitable for high temperature molten alloys. A crucible containing molten metal is suspended, and a rotational oscillation is given to the crucible electromagnetically. The oscillation was damped by the friction of molten metal. The viscosity is determined from the period of oscillation and the logarithmic decrement. The crucible was connected to a mirror block and an inertia disk made of aluminum, and whole of them was suspended by a wire made of platinum-13% rhodium alloy. A laser light is irradiated to the mirror. The reflection light is detected by the photo-detectors, and then, the logarithmic decrement of molten metal is determined. The viscosities of molten nickel and SS melts were measured up to 1823 K. In these results, the measured viscosity values of molten Ni and SS were close to those of the literature values of molten Ni and SS. By the equipment, the viscosity of molten SS+BC alloys are measured. The BC concentration dependence of the viscosity of molten SS+BC alloys is to be clarified.
Kasahara, Shigeki; Chimi, Yasuhiro; Hata, Kuniki; Hanawa, Satoshi
Zairyo To Kankyo, 68(9), p.240 - 247, 2019/09
In order to study environment assisted cracking mechanism of stainless steel under BWR primary coolant condition, effects of applied load on oxidation in the vicinity of crack tips of CT specimens were evaluated. Loaded CT specimens were immersed in an aqueous condition at 290C as a simulated BWR coolant condition, and microstructural observation on oxide near the tips of pre-cracks was carried out. Oxide inner layers, which consisted of fine grain magnetite containing Fe and Cr were formed, and oxide outer layers consisting of large grains of FeO were observed to cover the inner layers. FEM analysis of stress and strain in the loaded CT specimen suggests that both of dislocations due to localized plastic deformation and elastic strain could play important roles to accelerate inner oxide formation in the vicinity of the crack tip of the specimens.
Kasahara, Shigeki; Chimi, Yasuhiro; Hata, Kuniki; Fukuya, Koji*; Fujii, Katsuhiko*
Proceedings of 19th International Conference on Environmental Degradation of Materials in Nuclear Power Systems - Water Reactors (Internet), p.1345 - 1355, 2019/08
This paper describes empirical equation development of crack growth rates (CGR) in consideration of IASCC of neutron irradiated stainless steel to contribute to structural integrity assessment of BWR reactor internals. Empirical equations of CGR (da/dt) were developed based on a formula of da/dt = MK, assuming that "M" and "n" tend to be saturated with increasing neutron fluence. To obtain the empirical equations for normal water chemistry (NWC) and hydrogen water chemistry (HWC) of BWR, a data fitting with least square method was applied to the datasets consisting of F, K and CGR from post irradiation examinations of neutron irradiated stainless steel under simulated NWC and HWC conditions from open literature. As a result, calculated results by the equation for NWC showed good agreement with measured CGR data, meanwhile those for HWC did not. The above difference was seemed to be attributed that CGR data obtained under HWC conditions were scattered extensively.
Fukuya, Koji*; Fujii, Katsuhiko*; Chimi, Yasuhiro; Hata, Kuniki
Proceedings of 19th International Conference on Environmental Degradation of Materials in Nuclear Power Systems - Water Reactors (Internet), p.523 - 531, 2019/08
For structural integrity assessment on reactor internals of light water reactors, empirical equations of tensile properties as a function of neutron dose, and trend curves of stress-strain relations of neutron-irradiated austenitic stainless steels was proposed by fitting to recently developed database. The data in the database were obtained from reports of national projects in Japan and open literature, which was summarized in the form of data sheets. The empirical equations for tensile properties were formulated by using a saturation-type formulae. The equations were for CW 316 and SA 304/316 stainless steels in the temperature range of 280-350C and the dose range up to 80 dpa. Stress-strain relation curves were reproduced based on the Swift model. Obtained calculated results by the empirical equations and stress-strain relations were reasonably well fitted to experimental data. The effects of composition and cold-working, etc. on tensile properties were discussed.
Nakajima, Kunihisa; Nishioka, Shunichiro; Suzuki, Eriko; Osaka, Masahiko
Proceedings of 27th International Conference on Nuclear Engineering (ICONE-27) (Internet), 8 Pages, 2019/05
Cesium chemisorption models were developed for estimation of amount of cesium chemisorbed onto stainless steel type 304 (SS304) during light water reactor severe accident. However, existing chemisorption models cannot accurately reproduce experimental results. In this study, a modified cesium chemisorption model was constructed based on a penetration theory for gas-liquid mass transfer with chemical reaction and was able to adequately describe effects on concentration of cesium hydroxide in gaseous phase and silicon content in SS304. It was found that the modified model can more accurately reproduce the experimental data than the existing model.
Kasahara, Shigeki; Fukuya, Koji*; Fujimoto, Koji*; Fujii, Katsuhiko*; Chimi, Yasuhiro
JAEA-Review 2018-013, 171 Pages, 2019/01
For structural integrity assessment of reactor internals of light water reactors, it is important to evaluate and predict the property changes of structural materials, based on existing data obtained from austenitic stainless steel irradiated with neutrons. Compilation of the data into tables is valuable for discussing the representative or the most probable values of the properties applied to the assessment. When the data compilation, the data must be distinguished clearly in consideration of different service conditions of core internals of pressurized water reactors (PWR) and boiling water reactors. Main objective of this work is to provide material property tables of irradiated austenitic stainless steel which will be applicable for assessment of structural integrity of core internals of PWRs. To compile the table, published literature reporting irradiated stainless steel data were surveyed and screened by considering the service conditions of PWRs. In addition to the data, various parameters for the data evaluation, e.g. chemical compositions and pre-treatments of the materials, irradiation and examination conditions, were extracted from the literature, and listed into tables.
Kasahara, Shigeki; Fukuya, Koji*; Koshiishi, Masato*; Fujii, Katsuhiko*; Chimi, Yasuhiro
JAEA-Review 2018-012, 180 Pages, 2018/11
For structural integrity assessment of reactor internals of light water reactors, it is important to evaluate and predict the property changes of structural materials, based on existing data obtained from austenitic stainless steel irradiated with neutrons. Compilation of the data into tables is valuable for discussing the representative or the most probable values of the properties applied to the assessment. In the process of the data compilation, the data must be distinguished clearly in consideration of different service conditions of core internals of boiling water reactors (BWR) and pressurized water reactors. Main objective of this work is to provide material property tables of irradiated austenitic stainless steel which will be applicable for assessment of structural integrity of core internals of BWRs. To compile the table, published literature reporting irradiated stainless steel data were surveyed and screened by considering the service conditions of BWRs. In addition to the data, various parameters for the data evaluation, e.g. chemical compositions and pre-treatments of the materials, irradiation and examination conditions, were extracted from the literature, and listed into the tables.
Kokubo, Hiroki*; Nishi, Tsuyoshi*; Ota, Hiromichi*; Yamano, Hidemasa
Nippon Kinzoku Gakkai-Shi, 82(10), p.400 - 402, 2018/09
It is important to obtain the viscosity of a mixed alloy consisting of molten stainless steel and boron-carbide (SUS316L + BC alloy) for the improvement of severe accident assessment methodology for sodium-cooled fast reactors. In this study, the viscosities of the molten nickel (Ni) and stainless steel (SUS316L) were measured by the oscillating crucible method to confirm the performance of the viscosity measurement apparatus as a first step. The viscosities of molten Ni and SUS316L melts were measured up to 1823 K. It was found that the measured viscosity values of molten Ni and SUS316L were estimated from the deviation of the experimental data, were 4% and 3%, respectively. It was also found that those of molten Ni and SUS316L were close to those of the literature values of molten Ni and similar composite stainless steels. Moreover, we tentatively measured the viscosity of molten SUS316L-5 mass%BC alloy. The fitted results of the viscosity for molten Ni and SUS316L were obtained.
Soma, Yasutaka; Komatsu, Atsushi; Ueno, Fumiyoshi
Zairyo To Kankyo, 67(9), p.381 - 385, 2018/09
In-situ measurement of electrical conductivity of solution within crevice of SUS316L stainless steel in 288C water has been conducted with newly developed electrochemical sensor system. The sensor measures local electrical conductivity of crevice solution beneath the electrode () with electrochemical impedance method. The sensors were installed at different positions within tapered crevice of SUS316L stainless steel. The crevice specimen with the sensors were immerged into 288C, 8 MPa, pure oxygen saturated high purity water for 100 h. at a position with crevice gap of 59.3m was 8-11S/cm, least deviate from conductivity of 288C pure water (4.4S/cm) and no localized corrosion occurred. On the contrary, at a position with crevice gap of 4.4m increased with time and showed maximum value of 1600S/cm at 70 h. Localized corrosion occurred in the vicinity of this position. Thermodynamic equilibrium calculation showed of 1600S/cm being equivalent to pH of 3 to 3.7. It can be concluded that acidification occurred in tight crevice even under high purity bulk water and resulted in localized corrosion.
Naoe, Takashi; Wakui, Takashi; Kogawa, Hiroyuki; Wakai, Eiichi; Haga, Katsuhiro; Takada, Hiroshi
Advanced Experimental Mechanics, 3, p.123 - 128, 2018/08
A mercury target vessel, composed of SUS316L, is used for the pulsed neutron source and is assembled via TIG welding. While in operation, the target vessel suffers ca. 10 loading cycles with a high strain rate of ca. 50 s because of the proton-beam-induced pressure waves in mercury. The gigacycle fatigue strength for solution annealed SUS316L stainless steels and its welded specimens were investigated through ultrasonic fatigue tests. The experimental results showed that an obvious fatigue limit was not observed at fewer than 10 cycles for the base metal. In the case of no weld defects observed via penetration tests, the fatigue strength of the removed-weld-bead specimen, in which the weld lines were arranged at the center of the specimen, appeared to be slightly higher than that of the base metal. By contrast, as-welded specimens with the weld bead intact showed apparent degradation of the fatigue strength owing to the stress concentration around the weld toe.
Soma, Yasutaka; Ueno, Fumiyoshi
Zairyo To Kankyo, 67(5), p.222 - 228, 2018/05
Localized corrosion in crevice of SUS316 stainless steel after immersion in 288C high purity water with dissolved oxygen concentration of 32 ppm for 100 h was analyzed. Two different types of localized corrosion initiated on grain boundary and inclusions. The former initiated on grain boundary and oxide grown into grain matrix. The oxidized area showed duplex structure composed of microcrystalline FeCrO and island-shaped residual metals. The latter initiated on inclusions containing Ca and S and microcrystalline FeCrO grown into metal matrix. These localized corrosion occurred selectively in oxygen depleted area indicated formation of macroscopic corrosion cell with the corroded area as anode and surrounding oxygenated area as cathode.
Iida, Yoshihisa; Nakadoi, Yasumasa; Yamaguchi, Tetsuji
Genshiryoku Bakkuendo Kenkyu (CD-ROM), 24(1), p.53 - 64, 2017/06
The information on the contaminated water treatment in Fukushima Daiichi Nuclear Power Station announced by Tokyo Electric Power Co., Inc. (TEPCO) were summarized in terms of the management of the secondary wastes, for the purpose of accumulating technical knowledge for long-term storage of the wastes. Concerns for the long-term soundness of waste storage containers were pointed out as follows, corrosion of stainless steel containers exposed to radiation in the presence of chloride ions, corrosion of stainless steel containers under acidic conditions or in the presence of activated carbon, and radiation degradation of the high-performance container (HIC) in which slurry was stored.
Takeuchi, Tomoaki; Nakano, Hiroko; Uehara, Toshiaki; Tsuchiya, Kunihiko
Nuclear Materials and Energy (Internet), 9, p.451 - 454, 2016/12
no abstracts in English
Soma, Yasutaka; Kato, Chiaki; Ueno, Fumiyoshi
Fushoku Boshoku Kyokai Dai-63-Kai Zairyo To Kankyo Toronkai Koenshu, p.253 - 256, 2016/10
Contribution of corrosion to advance of stress corrosion cracking (SCC) of stainless steel in high temperature water must be assessed because serious corrosion can be found within SCC of light water reactors. The corrosion took the form of both intergranular and grain-matrix attack indicate aggressive corrosion condition was formed in the crevice of the SCC. We have investigated the crevice environment electrochemically and found that local electrical conductivity of the crevice solution at satisfactory narrow crevice gap having more than 100 times higher than that of bulk solution. In this research we assessed effect of cyclic deaerated and aerated bulk solution to the crevice environment. The result showed that electrical conductivity of the crevice solution under the deaerated bulk solution increased more than 10times by injection of pure oxygen suggest that the dissolved oxygen caused aggressive corrosion condition within the crevice.
Hojo, Kiminobu*; Hayashi, Shotaro*; Nishi, Wataru*; Kamaya, Masayuki*; Katsuyama, Jinya; Masaki, Koichi*; Nagai, Masaki*; Okamoto, Toshiki*; Takada, Yasukazu*; Yoshimura, Shinobu*
Mechanical Engineering Journal (Internet), 3(4), p.16-00083_1 - 16-00083_16, 2016/08
Performance demonstration certification of non-destructive inspection for cast stainless steel (CASS) has been planned but the target flaw depth to be detected has not been determined yet in Japan. The target flaw size is closely connected to the allowable flaw size which is determined by flaw evaluation of the rules on fitness-for-service. For rational mitigation of the acceptable flaw size, application of probabilistic fracture mechanics (PFM) is one of the useful countermeasures compared with deterministic approach. In this paper, benchmark problems for a CASS pipe were proposed with intention applying and verifying PFM codes. As the fracture modes, fatigue crack extension, plastic collapse and ductile crack initiation were assumed. Six organizations participated in the benchmark analysis and failure probabilities from them were compared. As a result the failure probability of each problem showed good agreement and the code for application of CASS issue has been verified.
Hatano, Masaharu*; Kubota, Yoshiki*; Shobu, Takahisa; Mori, Shigeo*
Philosophical Magazine Letters, 96(6), p.220 - 227, 2016/06
We have investigated the formation process of '-martensite from the -phase induced by external strain using in-situ synchrotron diffraction experiments, combined with Lorentz transmission electron microscopy (TEM) and high-resolution TEM observations. It is clearly demonstrated that -martensite with hexagonal symmetry appears as an intermediate structure during the plastic deformation of SUS304 stainless steel. In addition to stacking faults and dislocations, interfaces between the twin structures presumably play a key role in the formation of -martensite.
Irisawa, Eriko; Ueno, Fumiyoshi; Kato, Chiaki; Abe, Hitoshi
Zairyo To Kankyo, 65(4), p.134 - 137, 2016/04
In order to investigate the effect of boiling under reduced pressure on corrosion of stainless steel in the nitric acid solution, the corrosion tests simulating the high-level radioactive liquid waste evaporator were performed. The results of immersion tests of stainless steels in the solution with and without boiling showed that the corrosion rates in boiling solution were larger than those in not boiling solution in case of same temperature of solution. Moreover, the cathode polarization curves showed that the corrosion potential of stainless steel in boiling solutions were shifted nobler, and the current intensity became larger than that in not boiling solutions. According to these results, it can be concluded that boiling of solution under reduced pressure accelerate the corrosion rates.
Nemoto, Yoshiyuki; Oishi, Makoto; Ito, Masayasu; Kaji, Yoshiyuki; Keyakida, Satoshi*
Hozengaku, 14(4), p.83 - 90, 2016/01
Authors previously reported that magnetic data obtained by using Eddy current method and AC magnetization method showed correlation with the increase of susceptibility of the irradiation assisted stress corrosion cracking (IASCC) on neutron irradiated austenitic stainless alloy specimens. To discuss the mechanism of the correlation, microstructure observation was conducted on the irradiated specimen, and magnetic permalloy phase (FeNi) formation along grain boundary was revealed in this work. From this result, the radiation induced magnetic phase formation along grain boundary seems to be a factor of the magnetic property change of the irradiated materials, and related to the correlation between magnetic data and IASCC susceptibility. In addition, sensor probe development was conducted in this work to obtain higher sensitivity and resolution. It was applied for magnetic measurement on type304 stainless steel irradiated up to different doses. In this case, magnetic ferrite phase was existed in the type304 stainless steel sample before irradiation therefore it was concerned that magnetic measurement on the irradiated ones would be disturbed by the magnetic signal from the pre-existing ferrite phase. In the magnetic measurements, increase of the magnetic data was clearly seen on the irradiated specimens. Thus, it was thought that the developed magnetic measurement technics can be applied for the irradiated austenite stainless steels which contain certain quantity of ferrite phase before irradiation.