JOPSS - Search Results

Journal Articles

Predictive and inverse modeling of a radionuclide diffusion experiment in crystalline rock at ONKALO (Finland)

Soler, J. M.*; Keklinen, P.*; Pulkkanen, V.-M.*; Moreno, L.*; Iraola, A.*; Trinchero, P.*; Hokr, M.*; ha, J.*; Havlov, V.*; Trpkoov, D.*; et al.

Nuclear Technology, 209(11), p.1765 - 1784, 2023/11

https://doi.org/10.1080/00295450.2023.2209234

Times Cited Count：6 Percentile：66.64(Nuclear Science & Technology)

JAEA Reports

An Attempt to estimate the migration pathway of slab-derived fluid using shear wave splitting analysis

Hiratsuka, Shinya; Asamori, Koichi; Saiga, Atsushi

JAEA-Research 2022-002, 38 Pages, 2022/06

JAEA-Research-2022-002.pdf:4.49MB

Deep groundwater originates from dehydration of Pacific and Philippine Sea slab subducting beneath Japanese islands, which has characteristics of high temperature and is rich in carbonate species. In this respect, it is very important for geological disposal of high-level radioactive waste to estimate reservoir and migration pathway of deep groundwater. The region where cracks are densely distributed can be regarded as the migration pathway of slab-derived fluid. It is highly probable that the region has strong anisotropy. Shear wave propagating through anisotropic media splits into two mutually orthogonally polarized waves due to shear wave polarization anisotropy. In this report, we applied shear wave splitting analysis to Hongu area of Tanabe City, Wakayama Prefecture and estimated the spatial distribution of leading shear wave polarization direction (LSPD) and arrival time difference between leading and lagging shear waves (dt). Based on comparison with helium isotope ratio of ground water and bubbling gas samples and two-dimensional resistivity structure estimated by previous study, we attempt to estimate migration pathway of slab-derived fluid in Hongu area of Tanabe City, Wakayama Prefecture. The main results are summarized as follows. When helium isotope ratio of groundwater and bubbling gas samples is high, dt value tends to be large. Shear wave propagating through high and low resistivity anomaly zone show small and large dt values, respectively. Previous study suggested that slab-derived fluid migrates from deeper part of western side of Hongu area and wells out in Yunomine and Kawayu hot springs. This is consistent with spatial distribution of dt values estimated by this study.

Journal Articles

Experimental and analytical investigation of formation and cooling phenomena in high temperature debris bed

Hotta, Akitoshi*; Akiba, Miyuki*; Morita, Akinobu*; Konovalenko, A.*; Vilanueva, W.*; Bechta, S.*; Komlev, A.*; Thakre, S.*; Hoseyni, S. M.*; Skld, P.*; et al.

Journal of Nuclear Science and Technology, 57(4), p.353 - 369, 2020/04

https://doi.org/10.1080/00223131.2019.1691078

Times Cited Count：22 Percentile：72.39(Nuclear Science & Technology)

JAEA Reports

Development of neutron transport calculation codes for 3-D hexagonal geometry, 2; Improvement and enhancement of the MINISTRI code

Sugino, Kazuteru; Takino, Kazuo

JAEA-Data/Code 2019-011, 110 Pages, 2020/01

JAEA-Data-Code-2019-011.pdf:3.37MB

A deterministic discrete ordinates method (SN method) transport calculation code for three-dimensional hexagonal geometry has been developed as the MINISTRI code (Ver. 7.0). MINISTRI is based on the triangle-mesh finite difference method, which can perform neutron transport calculations with high accuracy for cores of fast power reactors and assemblies of the Russian BFS critical facility. The present study has derived a proper scheme for remarkably improving the convergence of MINISTRI by investigating the issue of previous MINISTRI (Ver. 1.1), which sometimes plays a poor convergence performance in calculations for large-scale power reactor cores. The verification test of improved MINISTRI has been carried out for various cores by setting the reference result as the multi-group Monte-Carlo calculation with the same cross-sections as used in MINISTRI. As a result, it is found that the agreements are within 0.1% for eigenvalues and within 0.7% for power distributions. Thus, the satisfying accuracy of MINISTRI has been confirmed. In order to reduce the calculation time, the initial diffusion calculation scheme and the parallel processing have been implemented. As a result, the calculation time is reduced to the approximately one tenth compared with previous MINISTRI. Furthermore, adoption of the treatment of the anisotropic cell streaming effect, preparation of the perturbation calculation tool, implementation of the function for specification of the triangle-mesh-wise material and merging of the hexagonal-mesh calculation code MINIHEX have been carried out. Thus, the versatility of MINISTRI has been enhanced.

Journal Articles

Anisotropically conducting films consisting of sub-micron copper wires in the ion track membranes of poly(ethylene terephthalate)

Maekawa, Yasunari; Koshikawa, Hiroshi; Yoshida, Masaru

Polymer, 45(7), p.2291 - 2295, 2004/03

https://doi.org/10.1016/j.polymer.2003.11.011

Times Cited Count：8 Percentile：27.45(Polymer Science)

Ion track membranes of poly(ethylene terephthalate) (PET) are applied to the production of anisotropically conducting films possessing copper wires of less than sub-micron in diameter. The membranes possessing cylindrical pores of 1.9 m and 200 nm in diameter were prepared by irradiation of $^{129}$ Xe $^{23+}$ ion beams followed by etching in an aqueous NaOH. Copper wires were deposited into the pores by electrochemical plating in aqueous copper sulfate solution to prepare the PET/Cu hybrid membranes. The copper wires with 1.9 m in diameter showed wavelike surface roughness, resulting from the roughness of the pore side wall, whereas the copper wires with 200 nm in diameter showed smooth surfaces. The resistances of the membranes measured by a four terminal resistance method are in good agreement with the calculated values, indicating that the hybrid membranes possess conductivity perpendicular to the membrane surfaces but not parallel to the surfaces.