Practical approach of airborne gamma-ray spectrometry using UAVs for evaluating ground-level dose rates

Ji, Y.-Y.*; Ji, W.*; Kim, K.*; Kim, M. J.*; 越智 康太郎; 森下 祐樹; 眞田 幸尚

Radiation Physics and Chemistry, 244, p.113781_1 - 113781_12, 2026/02

https://doi.org/10.1016/j.radphyschem.2026.113781

UAVによる空中線スペクトロメトリは迅速な放射線マッピングを可能にするが、飛行高度による減衰、視野効果、汚染の不均一性、地形条件により地上線量率の定量評価は難しい。本研究では福島第一原子力発電所周辺でホバリング飛行による校正と地上測定を組み合わせた実用的手法を開発した。二重指数モデルで高度補正係数を導出し、三脚およびバックパック測定と比較した結果、不均一サイトでの補正は系統誤差を生むが、均一サイトでの校正により一致が改善された。適切な補正を用いれば、UAV空中測定は信頼できる線量率分布評価が可能である。

Experimental study of AESOP code for aerosol removal behavior from a rising gas bubble in water pool and parametric study for application to sodium pool system

宮原 信哉*; 鯉江 竜輔*; 宇埜 正美*; 河口 宗道*; 佐藤 理花; 清野 裕

Nuclear Engineering and Design, 446(Part A), p.114523_1 - 114523_14, 2026/01

https://doi.org/10.1016/j.nucengdes.2025.114523

In a postulated accident of fuel pin failure of a sodium-cooled fast reactor, a fission product of cesium will be released from the failed pin as an aerosol such as cesium iodide and/or cesium oxide together with a fission product noble gas such as xenon and krypton. The xenon and krypton released with the cesium aerosols into the sodium coolant as bubbles have an influence on the removal of cesium aerosols by the sodium pool in a period of bubble rising to the sodium pool surface. Then, the cesium aerosols could transfer into the containment vessel as an initial inventory of a source term. To meet this phenomenon, the computer program AESOP (AErosol scrubbing in SOdium Pool) has been developed to deal with the expansion and the deformation of the bubble together with the aerosol absorption considering the effects of the particle size distribution and the agglomeration in aerosols. In this study, simulation experiments have been conducted using simulant particles under the condition of room temperature in water pool and nitrogen gas bubble systems and the experimental results were compared with the analysis results calculated under the same condition by the AESOP code. Furthermore, to examine the applicability of the AESOP code to the sodium pool system, the sensitivities of the physical parameters on decontamination factor (DF) of fission product aerosols such as the initial bubble diameter, the sodium pool depth and the temperature, the aerosol particle diameter and the density, the initial aerosol concentration in the bubble had been studied and the analysis results were discussed for the sensitivities of the parameter as same as DF of the aerosol.

Re-evaluation of nuclear criticality characteristics for infinite and finite heterogeneous lattice systems composed of uranium-zirconium hydride fuel rods used in the TRIGA annular core pulse reactor NSRR

柳澤 宏司; 求 惟子

JAEA-Research 2025-010, 197 Pages, 2025/11

JAEA-Research-2025-010.pdf:3.5MB

TRIGA燃料棒の臨界リスクの把握とその取扱いの安全対策の検討のため、NSRR燃料棒からなる無限及び有限非均質格子体系の臨界特性を、燃料棒の詳細な計算モデルを用いて再評価した。再評価には、最新バージョンのJENDL-5を含むJENDLライブラリとMVPバージョン3コードが使用された。臨界特性として、無限及び水反射有限体系の中性子増倍率の変化を、格子ピッチと減速材水の密度をパラメータとして詳細に調べた。再評価された臨界特性の結果から、JENDL-5ライブラリを用いて、水反射の六角格子体系の最小臨界燃料棒本数は46.80.2本と得られた。さらに、TRIGA燃料棒には水素化ジルコニウム減速材と黒鉛反射材が備わっているため、減速材及び反射材としての水が存在しない場合の臨界到達可能性を検討した。その結果、水が存在しない場合でも、NSRR標準炉心に装荷されている燃料棒の本数よりも少ない115.70.6本の燃料棒で臨界に到達することが可能であることが分かった。

Development of a theoretical scaling factor method for the inventory estimation of difficult-to-measure nuclide Cs-135 in fuel debris and radioactive wastes

坂本 雅洋; 奥村 啓介; 神野 郁夫; 松村 太伊知; 寺島 顕一; Riyana, E. S.; 金子 純一*; 溝上 暢人*; 溝上 伸也*

Journal of Nuclear Science and Technology, 62(8), p.756 - 765, 2025/08

https://doi.org/10.1080/00223131.2025.2478926

In this paper, we propose a new nuclide inventory estimation method based on computational methods, called a "theoretical scaling factor method" for difficult-to-measure (DTM) nuclides in fuel debris and radioactive wastes. The theoretical scaling factor method provides a method similar to a conventional scaling factor method. The theoretical scaling factor method, however, does not require performing many measurements to obtain correlations between a key nuclide which is easy-to-measure and a DTM nuclide. Instead of actual analytical measurements, the results of theoretical calculations are used. A correlation equation between the key nuclide and the DTM nuclide is created based on the results of theoretical calculations, and the DTM nuclide is deterministically estimated using the measurement value of the key nuclide only. In this paper, we selected Cs-135 as the DTM nuclide and Cs-137 as the key nuclide. Cs-135 has a long half-life of 2.310 years and is one of the important fission products in the safety evaluation for the geological disposal of high-level radioactive waste, because it dissolves and migrates in groundwater easily. We confirmed the validity of the proposed method using measured data of Cs-137 and Cs-135 on radioactive wastes from the Fukushima Daiichi Nuclear Power Station (1F) accident obtained by many researchers. It can be used as a rational and efficient technology to reduce the analysis costs of various types of fuel debris and radioactive waste present at 1F.

Enhanced strength and ductility in an additively manufactured Al10SiMg alloy at cryogenic temperatures

Naeem, M.*; Rehman, A. U.*; Romero Resendiz, L.*; Salamci, E.*; Aydin, H.*; Ansari, P.*; Harjo, S.; Gong, W.; Wang, X.-L.*; 他3名*

Communications Materials (Internet), 6, p.65_1 - 65_13, 2025/04

https://doi.org/10.1038/s43246-025-00793-4

The need for lightweight materials with mechanical integrity at ultralow temperatures drives the development of advanced alloys for cryogenic use. Additive manufacturing via laser powder bed fusion (LPBF) offers a scalable way to create alloys with tailored properties. Here, we show that LPBF-processed Al10SiMg exhibits a high ultimate tensile strength (395 MPa) and uniform elongation (25%) at 15 K. These enhancements stem from grain refinement, increased geometrically necessary dislocations, and stress partitioning between the Al matrix and the stiffer Si phase, aiding strain accommodation. neutron diffraction reveals that the Si phase, with its higher yield strength, bears most of the load, while the Al matrix undergoes continuous strain hardening, extending deformation capacity. These results highlight Al10SiMg's promise for cryogenic applications such as hydrogen storage, aerospace, and quantum computing hardware.

Analyses of stress intensity factor solutions for subsurface flaws in flat plates

Li, S.; Li, Y.; Lu, K.*; Lacroix, V.*; Dulieu, P.*

Proceedings of the ASME 2024 Pressure Vessels & Piping Conference (PVP 2024) (Internet), 18 Pages, 2024/07

https://doi.org/10.1115/PVP2024-122733

The stress intensity factor (SIF) solutions for subsurface flaws in flat plates are provided in Appendix A of ASME Boiler and Pressure Vessel Code Section XI. A part of the SIF solutions was initially provided in the 2015 edition. The solutions were obtained for the fourth order polynomial stress distribution base on the influence function method. The solutions were expanded in the 2021 edition for subsurface flaws near the surface of the plate. The additional solutions were obtained based on the J-integral from the elastic finite element analyses. However, recent investigations have found that there is a minor discrepancy in trend between the two sets of SIF solutions because they were obtained by using different numerical methods. Although the discrepancy is very small, the change in trend causes some difficulties in engineering applications. In this work, the SIF solutions are recalculated using the same numerical method based on the J-integral from elastic finite element analyses. The results are compared with the solutions in the current Section XI, RSE-M, and are finally cross-checked with the results obtained from an independent numerical model. The results are useful to eliminate the discrepancy in trend in the SIF solutions for subsurface flaws in flat plates in the current edition of Section XI.

In-situ neutron diffraction study of serration-involved ultra-cryogenic deformation behavior at 15 K

Kim, Y. S.*; Chae, H.*; Lee, D.-Y.*; Han, J. H.*; Hong, S.-K.*; Na, Y. S.*; Harjo, S.; 川崎 卓郎; Woo, W.*; Lee, S.-Y.*

Materials Science & Engineering A, 899, p.146453_1 - 146453_7, 2024/05

https://doi.org/10.1016/j.msea.2024.146453

This work focused on the mechanical properties and serration-involved deformation behavior of advanced alloys at 15 K. Evolution of stacking faults and -martensite improved the mechanical performance of CoCrNi alloys, and significant strain-induced martensite transformation of DED-SS316L led to superior strength and strain hardening. A magnitude in stress drop was governed by dislocation density, phase type, and lattice defects, irrespective of processing method. FCC {200} notably was influenced recovery behavior after stress drop, and the contribution of strain energy density by serration on tensile toughness was the greatest for HR-CoCrNi.

Archie's cementation factors for natural rocks; Measurements and insights from diagenetic perspectives

Yuan, X.*; Hu, Q. H.*; Fang, X.*; Wang, Q. M.*; Ma, Y.*; 舘 幸男

Sedimentary Geology, 465, p.106633_1 - 106633_14, 2024/05

https://doi.org/10.1016/j.sedgeo.2024.106633

Archie's cementation factor, m, is a critical parameter for petrophysical studies, and the value is influenced by several factors such as the shape, type, and size of grains, degrees of diagenesis, and associated pore structure. Using integrated experimental and theoretical approaches, the goal of this study is to obtain the cementation factor of rocks (both reservoir rock and caprock) and assess the impact of diagenesis processes on the values of the cementation factor. Thirteen samples of geologically diverse rocks (six mudstones, four fossiliferous limestones, two marbles, and one sandstone) were selected to achieve these research objectives. Two approaches, the diffusion of gas tracers and the Bosanquet formula calculation using pore-throat sizes from mercury intrusion porosimetry analyses, were used to derive the cementation factors of these rock samples. These rocks were categorized into two groups based on the correlation between average pore-throat diameter and diffusivity, and an exponential-law relationship between the cementation factor and porosity was determined for these sample groups. In addition, thin-section petrography and field emission-scanning electron microscopy observations were utilized to investigate diagenetic processes, with four diagenetic patterns being established: (1) strong compaction, strong cementation, and weak dissolution-diagenesis pattern; (2) weak compaction, medium cementation, and weak dissolution-diagenesis pattern; (3) weak compaction, medium cementation, and strong dissolution-diagenesis pattern; and (4) fracture-matrix pattern. The results indicated that diagenetic processes and microfractures contribute to the variability in the cementation factors in these rock samples.

Key role of temperature on delamination in solid-state additive manufacturing via supersonic impact

Wang, Q.*; Ma, N.*; Huang, W.*; Shi, J.*; Luo, X.-T.*; 冨高 宙*; 諸岡 聡; 渡邊 誠*

Materials Research Letters (Internet), 11(9), p.742 - 748, 2023/09

https://doi.org/10.1080/21663831.2023.2227221

Cold spray (CS) has emerged as a representative of solid-state additive manufacturing (AM) via supersonic impact. It enables a high deposition rate of solid-state microparticles. Delamination, however, tends to occur when depositing too thick; this remains to be conquered. Here, a CS-like process, warm spray (WS), was presented. Interestingly, it was found that the appropriate increase in particle temperature can effectively reduce the residual stress amplitude, relieving the concentrated tensile stress and safeguarding the additively manufactured components from interfacial delamination even when depositing too thick. The key role of temperature on delamination was identified in solid-state AM via supersonic impact.

Investigation of the core neutronics analysis conditions for evaluation of burn-up nuclear characteristics of the next-generation fast reactors

滝野 一夫; 大木 繁夫

JAEA-Data/Code 2023-003, 26 Pages, 2023/05

JAEA-Data-Code-2023-003.pdf:1.66MB

次世代高速炉は、従来炉よりも高い炉心取出燃焼度を目指しているため、炉心核設計の高度化が求められる。そのため、燃焼核特性解析では、計算コストを抑えつつ十分な計算精度が得られる適切な解析条件が必要とされる。そこで、次世代高速炉の燃焼核特性の計算精度に及ぼす解析条件の影響を、中性子エネルギー群、中性子輸送理論、空間メッシュに着目して調査した。本検討では燃焼核特性として、平衡サイクルにおける臨界性、燃焼反応度、制御棒価値、増殖比、集合体単位の出力分布、最大線出力、ナトリウムボイド反応度、ドップラー係数を取り扱った。検討の結果、エネルギー群を18群とし、拡散近似を用いて1集合体あたり6メッシュ分割して、エネルギー群、空間メッシュ、輸送効果の補正係数を適用することが最適であることが分かった。