Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Rodriguez, D.; Rossi, F.; Takahashi, Tone
IEEE Transactions on Nuclear Science, 71(3), p.255 - 268, 2024/03
Times Cited Count:0 Percentile:0.00(Engineering, Electrical & Electronic)Wakui, Takashi; Wakai, Eiichi; Naoe, Takashi; Shintaku, Yohei*; Li, T.*; Murakami, Kazuya*; Kanomata, Kenichi*; Kogawa, Hiroyuki; Haga, Katsuhiro; Takada, Hiroshi; et al.
Journal of Nuclear Materials, 506, p.3 - 11, 2018/08
Times Cited Count:4 Percentile:34.56(Materials Science, Multidisciplinary)The mercury target vessel is designed as multi-walled structure with thin wall (min. 3 mm), and assembled by welding. In order to estimate the structural integrity of the vessel, it is important to measure the defects in welding accurately. For nondestructive tests of the welding, radiographic testing is applicable but it is difficult to detect for some defect shapes. Therefore it is effective to do ultrasonic testing together with it. Because ultrasonic methods prescribed in JIS inspect on the plate with more than 6 mm in thickness, these methods couldn't be applied as the inspection on the vessel with thin walls. In order to develop effective method, we carried out measurements using some testing method on samples with small defect whose size is specified. In the case of the latest phased array method, measured value agreed with actual size. It was found that this method was applicable to detect defects in the thin-walled structure for which accurate inspection was difficult so far.
Furusawa, Akinori; Nishimura, Akihiko; Takebe, Toshihiko*; Nakamura, Masaki*; Takenaka, Yusuke*; Saijo, Shingo*; Nakamoto, Hiroyuki*
E-Journal of Advanced Maintenance (Internet), 9(2), p.44 - 51, 2017/08
The aim of this work is to investigate the applicability of ultrasonic guided wave for evaluation of laser beam butt-welding quality. Ten in total test pipes having welding seam is prepared. Two piece of pipe are jointed and continuous laser beam is irradiated on the edges, varying laser irradiation power, welding side and surface profile of the adjacent edges of the pipe. Ultrasonic guided wave testing experiment is performed on the pipes. Torsional mode guided wave is excited by EMAT. The experimental results are analyzed and issues are discussed. The reflection wave bullet from the poor interface of the welding seam is clearly observed, whereas no reflection from fine welded line. From the aspect of laser irradiation power, welding side and surface profile of the adjacent edges, the relation between the interface condition and detection wave bullet are analyzed. It is found that the ultrasonic guided wave technologies have the potential for evaluating laser beam butt-welding seam.
Ishii, Toshimitsu; Ooka, Norikazu; Hoshiya, Taiji; Kobayashi, Hideo*; Saito, Junichi; Niimi, Motoji; Tsuji, Hirokazu
Journal of Nuclear Materials, 307-311(Part.1), p.240 - 244, 2002/12
Times Cited Count:3 Percentile:22.89(Materials Science, Multidisciplinary)no abstracts in English
Eto, Motokuni; Ishii, Toshimitsu; Inagaki, Terumi*; Okamoto, Yoshizo*
Carbon, 40(3), p.285 - 294, 2002/03
Times Cited Count:9 Percentile:36.37(Chemistry, Physical)no abstracts in English
Ishii, Toshimitsu; Ooka, Norikazu; Naka, Michihiro; Kanaya, Kunio; Saito, Junichi; Okamoto, Yoshizo*
Proceedings of 6th Far-East Conference on Nondestructive Testing (FENDT '02), p.273 - 278, 2002/00
no abstracts in English
Ishihara, Masahiro; Hanawa, Satoshi; Iyoku, Tatsuo; Shiozawa, Shusaku
Tanso, 2001(196), p.39 - 48, 2001/02
no abstracts in English
Ishihara, Masahiro; Shibata, Taiju
Dai-4-Kai Kozobutsu No Anzensei, Shinraisei Ni Kansuru Kokunai Shimpojiumu Koen Rombunshu, p.101 - 108, 2000/00
no abstracts in English
Naka, Michihiro; ; Ooka, Norikazu; ; Ito, Haruhiko; Baba, Osamu
Proc. of CORENDE, 3 Pages, 1997/00
no abstracts in English
Ishihara, Masahiro; Saikusa, Akio; Iyoku, Tatsuo; Shiozawa, Shusaku; Ooka, Norikazu; ; ; ; ;
JAERI-M 93-197, 44 Pages, 1993/09
no abstracts in English