Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
畑 浩二*; 丹生屋 純夫*; 青柳 和平
International Journal of the JSRM (Internet), 20(1), p.240104_1 - 240104_4, 2024/11
地層処分技術の信頼性向上において、長期間にわたる岩盤のモニタリングが重要な研究課題となる。そこで、2014年に、幌延深地層研究センターの350m以深の立坑周辺に、岩盤掘削時の振動(AE)、間隙水圧、温度の3種類の特性を取得できる光ファイバー式センサーを設置し、岩盤の水理・力学的な挙動のモニタリングを開始した。計測の結果、立坑の掘削中は、壁面から約1.5mの範囲でAEが頻発した。また、同領域における透水係数は、健岩部と比較して24桁高かった。さらに、数値解析の結果、立坑掘削時の間隙水圧の上昇が、立坑周辺の割れ目発生の主な要因であることを明らかにした。これらの計測・解析結果を基に、掘削損傷領域の概念モデルを構築した。このモデルは、地層処分において、安全評価に資する情報として活用されることが期待できる。
畑 浩二*; 丹生屋 純夫*; 青柳 和平; 宮良 信勝*
Journal of Rock Mechanics and Geotechnical Engineering, 16(2), p.365 - 378, 2024/02
被引用回数:2 パーセンタイル:81.57(Engineering, Geological)山岳トンネルや地下備蓄基地などの地下空洞の掘削時には、応力再配分の影響により空洞周辺岩盤に損傷が生じる。このような領域では、亀裂や不連続面が発生することから、発生に伴う振動(アコースティックエミッション、AE)が生じる。本研究では、長期的な立坑周辺岩盤のモニタリングのために、光ファイバー式のAEセンサー,間隙水圧計を1つのボーリング孔に設置できるプローブを開発した。計測の結果、立坑掘削に伴ってAEの発生数が顕著となり、さらに立坑壁面から1.5mの範囲で2から4桁の透水係数の増大を確認した。さらに、数値解析の結果、間隙水圧変化と割れ目の発達領域を適切に再現できた。これらの結果を踏まえ、立坑周辺の掘削損傷領域の概念モデルを構築した。なお、この成果は、高レベル放射性廃棄物処分時の安全評価の信頼性の向上に資するものである。
本島 貴之*; 小池 真史*; 萩原 健司*; 青柳 和平
第46回岩盤力学に関するシンポジウム講演集(CD-ROM), p.208 - 213, 2019/01
大深度立坑掘削の標準工法であるショートステップ工法は、地山を緩ませずに断面を確保できる優れた工法である。ただし、国内に広く分布する堆積岩中への立坑構築を見据えた場合、特に低岩盤強度、初期地圧の異方性、もしくは高地圧といった不利な条件がある場合には覆工コンクリート応力が過大となることが想定される。本研究では支保への応力低減を目的としてショートステップ工法に二重支保・遅れ覆工の考え方を導入し、同手法の成立性について三次元逐次掘削解析にて検討を行うことで有効性を確認した。検証解析は日本原子力研究開発機構が実施している幌延深地層研究計画での原位置観測データを利用し、深度とともに地圧が増加するのに対し、岩盤強度が横ばいとなる厳しい条件下で実施した。
青柳 和平; 石井 英一; 藤田 朝雄; 本島 貴之*
第44回岩盤力学に関するシンポジウム講演集(CD-ROM), p.313 - 318, 2016/01
堆積軟岩を対象とする幌延深地層研究センターの深度350m以深の東立坑周辺に生じた掘削損傷領域の拡がりとその破壊様式を推定することを目的として、透水試験、BTV観察、立坑周辺のボーリング孔内水位の連続モニタリング、立坑壁面の観察を実施した。結果として、立坑壁面から2m以内で、透水係数が約1-3オーダー増大したことが確認された。これは、BTV観察により捉えられた割れ目の分布に整合する結果であった。また、立坑掘削深度がボーリング孔底深度に達した段階で水位の急激な低下が見られたことから、掘削直後に瞬間的に割れ目が発達し、壁面へ連結したことが推定された。さらに、立坑掘削に伴って発生する割れ目は引張のメカニズムで発生しており、壁面を取り囲む形で分布することがわかった。
津坂 仁和*; 稲垣 大介*; 名合 牧人*; 井尻 裕二*
Proceedings of 8th Asian Rock Mechanics Symposium (ARMS-8) (USB Flash Drive), 9 Pages, 2014/10
This study describes the analysis performed on the West Access Shaft of the Horonobe Underground Research Laboratory, which was expected to intersect a fault at the depth of approximately 320 m. Field observation, and measurement data were used to determine analysis conditions including magnitude and orientation of in-situ stress, boundary conditions, and rock mass properties. The fault was modeled as having a dip angle of 40 degrees and apparent thickness of 5 m (equivalent to the height of the excavated rock wall). The shaft sinking procedure was simulated using three-dimensional excavation analysis. The excavation involved installing concrete lining at every 2 m span. The analysis considered two cases of maximum in situ principal stress orientation: (1) perpendicular to and (2) parallel to the fault plane orientation. The results of the analysis indicate that the maximum excavation-induced stress, developed in a single-span lining concrete, was in the direction perpendicular to the maximum in situ principal stress orientation, unaffected by the fault plane orientation. The influence of the fault plane orientation on the excavation-induced stress state was found to be significant above and below the fault rather than in the fault. Another observation was that the excavation-induced stress magnitude appeared to be greater when the maximum in situ principal stress orientation was parallel to the fault plane orientation.