Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Muhammad, I.; Nagatake, Taku; Uesawa, Shinichiro; Ono, Ayako
Proceedings of 21st International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-21) (Internet), 12 Pages, 2025/08
This research aims to validate ACE-3D using data from a two-phase flow experiment. For this purpose, a two-phase flow experiment was conducted in a four-by-four unheated fuel assembly. In the experiment, the time-averaged void fraction distribution was measured using a wire mesh sensor system under high temperatures and high-pressure conditions. The experimental results were analyzed, and the data were visualized to understand better the behavior and characteristics of the two-phase flow in the fuel assembly. A two-phase flow data set is being developed, covering a wide range of experimental conditions, including higher-pressure regions, which can be used for validating thermal-hydraulic codes. Finally, the ACE-3D code was applied to the two-phase flow experiment. The calculation results were then compared to the experimental ones, and the issues were identified for improving ACE-3D in future simulations.
4 simulated fuel bundle for validation of thermal-hydraulics simulation codesOno, Ayako; Nagatake, Taku; Uesawa, Shinichiro; Shibata, Mitsuhiko; Yoshida, Hiroyuki
Proceedings of Specialist Workshop on Advanced Instrumentation and Measurement Techniques for Nuclear Reactor Thermal-Hydraulics and Severe Accidents (SWINTH-2024) (USB Flash Drive), 7 Pages, 2024/06
Japan Atomic Energy Agency (JAEA) is developing a neutronics/thermal-hydraulics coupling simulation code for light-water reactors. Thermal-hydraulic simulation codes applied to the coupling code are expected to calculate the void fraction distribution in a rod bundle under operational conditions, which are necessary for neutron transport simulation, and need to be validated using void fraction distribution data in a rod bundle under high-temperature and high-pressure conditions. Therefore, we have conducted the measurement of the instantaneous void distribution in the 4 4 simulated fuel bundle using a developed wire mesh sensor, which is installed in the pressurized two-phase flow experimental loop of JAEA to obtain the data for code validation.
6 rod bundleHan, X.*; Shen, X.*; Yamamoto, Toshihiro*; Nakajima, Ken*; Sun, Haomin; Hibiki, Takashi*
International Journal of Heat and Mass Transfer, 144, p.118696_1 - 118696_19, 2019/12
Times Cited Count：33 Percentile：80.68(Thermodynamics)Xiao, Y.*; Shen, X.*; Miwa, Shuichiro*; Sun, Haomin; Hibiki, Takashi*
Konsoryu Shimpojiumu 2018 Koen Rombunshu (Internet), 2 Pages, 2018/08
In order to develop constitutive equations of two-fluid model in rod bundle flow channels, experiments of adiabatic air-water upward two-phase flow in 66 rod bundle flow channel were performed. Local flow parameters such as void fraction, interfacial area concentration (IAC) and so on were measured by a double-sensor optical probe. The area-averaged void fraction and IAC data were compared with the predictions from a drift-flux model and an IAC correlation.
Shen, X.*; Schlegel, J. P.*; Hibiki, Takashi*; Nakamura, Hideo
Nuclear Engineering and Design, 333, p.87 - 98, 2018/07
Times Cited Count：14 Percentile：31.25(Nuclear Science & Technology)4 bundle at 2 MPaLiu, W.; Nagatake, Taku; Shibata, Mitsuhiko; Takase, Kazuyuki; Yoshida, Hiroyuki
Transactions of the American Nuclear Society, 114, p.875 - 878, 2016/06
To contribute to the clarification of the Fukushima Daiichi Accident, JAEA is working on getting instantaneous void fraction distribution data in steam water two - phase flow in rod bundle geometry under high pressure, high temperature condition, with using Wire Mesh Sensor (WMS) developed at JAEA for high pressure, high temperature condition, focusing on the low flow rate condition after the reactor scram. This paper reports the experimental results for the measured void fraction distribution in steam vapor two-phase flow in a 4 4 bundle under 1.6 MPa (202 
C), 2.1 MPa (215 C) and 2.6 MPa (226 C) conditions. The data is expected to be used in the validation of the detailed two-phase flow codes TPFIT and ACE3D developed at JAEA. The time and space averaged void fraction data is also expected being used in the validation of the drift flux models implemented in the two fluids codes, such as TRACE code.
Fuketa, Toyoshi;
Proc. of the 1st JSME/ASME Joint Int. Conf. on Nuclear Engineering, p.271 - 277, 1991/00
no abstracts in English
; Fuketa, Toyoshi;
Proc. of the Int. Conf. on Multiphase Flows 91-TSUKUBA,Vol. 2, p.247 - 250, 1991/00
no abstracts in English
