Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
neutron diffraction measurement during tensile deformation山下 享介*; 諸岡 聡; Gong, W.; 川崎 卓郎; Harjo, S.; 北條 智彦*; 興津 貴隆*; 藤井 英俊*
ISIJ International, 64(14), p.2051 - 2060, 2024/12
被引用回数：1 パーセンタイル：11.50(Metallurgy & Metallurgical Engineering)An Fe-0.15C-5Mn-0.5Si-0.05Nb steel annealed at 660
C and 685C showed L
ders deformation followed by high work hardening, with variations in Lders strain and hardening behavior. 
neutron diffraction during tensile tests analyzed phase stresses, strength contributions, and austenite orientation. Deformation-induced martensite contributed 
1000 MPa to strength near tensile failure, while austenite mainly enhanced ductility via transformation-induced plasticity. Austenite transformed to martensite during Lders deformation regardless of orientation, though 311-oriented grains tended to remain along the tensile direction.
neutron diffraction measurement during tensile deformation山下 享介*; 諸岡 聡; Gong, W.; 川崎 卓郎; Harjo, S.; 北條 智彦*; 興津 貴隆*; 藤井 英俊*
鉄と鋼, 110(3), p.241 - 251, 2024/02
被引用回数：0 パーセンタイル：0.00(Metallurgy & Metallurgical Engineering)A Fe-0.15C-5Mn-0.5Si-0.05Nb medium Mn steel annealed at 660C and 685C both exhibited inhomogeneous deformation with Luders deformation and extremely high work hardening rates, but with different Luders strain and work hardening behavior. 
neutron diffraction measurements during tensile test were performed to investigate changes in the phase stresses and in the contributed stresses to the strength of the constituent phases, and crystal orientation of austenite. The role of each constituent phase in the deformation and the effect of crystallographic orientation on austenite stability were discussed. Deformation induced martensite showed excellent phase stress and contributed to the strength approximately 1000 MPa, which is close to macroscopic tensile strength.
興津 貴隆*; 北條 智彦*; 諸岡 聡; 宮本 吾郎*
鉄と鋼, 110(3), p.260 - 267, 2024/02
被引用回数：0 パーセンタイル：0.00(Metallurgy & Metallurgical Engineering)We have investigated the dynamic tensile properties of 4, 5, 6-mass%-Mn-containing low carbon steels with multi-phase microstructures containing retained austenite. The five materials used were classified into two groups. The first group of materials, with around 10% of retained austenite, showed normal strain rete dependence of yield strength (YS) and tensile strength (TS) as in conventional high strength steels. The second group of materials, containing 25-36% of retained austenite, exhibited Lders elongation showed also normal strain rate dependence in YS and flow stress at Lders deformation, but TS varied in a complex manner. Among the second group, in the 4 Mn steel, TS was nearly constant at strain rates below 1 s
but increased slightly at higher strain rates. In the 5 and 6 Mn steels, TS once decreased up to the strain rate of 1 or 10 s, and then began to increase at higher strain rates. These behaviors were discussed in terms of temperature rise during plastic deformation causing suppression of martensitic transformation, and thermal stability of retained austenite. In the 4 Mn steel with relatively unstable retained austenite, almost all the austenite transforms regardless of strain rate. In the 5 and 6 Mn steels, where the retained austenite is moderately stable, strain induced transformation of austenite continues up to high plastic strain, providing a good balance of strength and ductility. At high strain rate, TS decreases slightly due to temperature rise, but at higher strain rates than 1 s, the strain rate sensitivity of flow stress in ferrite become prominent and the flow stress increases.
上路 林太郎*; Gong, W.; Harjo, S.; 川崎 卓郎; 柴田 曉伸*; 木村 勇次*; 井上 忠信*; 土田 紀之*
ISIJ International, 64(2), p.459 - 465, 2024/01
被引用回数：4 パーセンタイル：43.11(Metallurgy & Metallurgical Engineering)Deformation-induced martensitic transformation (DIMT) during tensile or compressive deformations of the bainitic steels with various carbon content (0.15%C, 0.25%C, 0.62%C) was studied. In all of the bainitic steels, the tensile deformation exhibited larger work hardening than the compression. This difference indicates the suppression of the DIMT at the compression, and actually the measurements of electron back scattering diffraction (EBSD) confirmed the less reduction of retained austenite at the compression of all the bainitic steels. Additionally, the steel with the highest carbon content was examined by in situ neutron diffraction and clarified the difference similar to that obtained by the EBSD measurement. The regression of the relation between the fraction of austenite and applied strain with the conventional empirical equation revealed that the kinetic of DIMT is strongly dependent with the stress polarity, but not significantly changed by the carbon content.
