Consideration of relationship between decommissioning with digital-twin and knowledge management

Taruta, Yasuyoshi; Yanagihara, Satoshi*; Hashimoto, Takashi*; Kobayashi, Shigeto*; Iguchi, Yukihiro; Kitamura, Koichi; Koda, Yuya; Tomoda, Koichi

Proceedings of 2020 International Conference on Nuclear Engineering (ICONE 2020) (Internet), 8 Pages, 2020/08

https://doi.org/10.1115/ICONE2020-16457

Decommissioning is a long-term project during which generations are expected to change. Therefore, it is necessary to appropriately transfer knowledge and technology to the next generation. In recent years, in the world of decommissioning, attempts have been made to apply advanced technologies such as utilization of knowledge management and virtual reality. This study describes adaptation in decommissioning from the viewpoint of utilizing IT technology called digital twin from the viewpoint of knowledge management.

Research concept of decommissioning knowledge management for the Fugen NPP

Taruta, Yasuyoshi; Yanagihara, Satoshi*; Iguchi, Yukihiro; Kitamura, Koichi; Tezuka, Masashi; Koda, Yuya

Proceedings of 26th International Conference on Nuclear Engineering (ICONE-26) (Internet), 6 Pages, 2018/07

https://doi.org/10.1115/ICONE26-81228

The IAEA are developed the discussion for those situations and pointed out the importance of nuclear knowledge management. The nuclear knowledge management is developing a database as nuclear knowledge management. In recent years, the IAEA has also advanced knowledge taxonomies on nuclear accidents. These studies are attempts to appropriately arrange and utilize huge amounts of information. Even in nuclear facilities in Japan, it is pointed out that veteran staff aging and loss of knowledge and skill caused by retirement. Therefore, we created a prototype database system to utilize past knowledge and information for ATR Fugen. Now, there are few cases of past decommissioning that can be utilized. This study of pilot model concept revealed that it is not sufficient to just prepare a past data and information. This is what information other than the construction report requires the decommissioning and what kind of information should be gathered.

Mechanical properties of full austenitic welding joint at cryogenic temperature for the ITER toroidal field coil structure

Iguchi, Masahide; Saito, Toru; Kawano, Katsumi; Chida, Yutaka; Nakajima, Hideo; Ogawa, Tsuyoshi*; Katayama, Yoshinori*; Ogata, Hiroshige*; Minemura, Toshiyuki*; Tokai, Daisuke*; et al.

Fusion Engineering and Design, 88(9-10), p.2520 - 2524, 2013/10

https://doi.org/10.1016/j.fusengdes.2013.02.165

ITER TFC structures are large welding structures made of heavy thick stainless steels. JAEA plans to apply narrow gap TIG welding with FMYJJ1 which is full austenitic stainless filler material to manufacture TFC structure. FMYJJ1 is specified in "Codes for Fusion Facilities -Rules on Superconducting Magnet Structure (2008)". In order to evaluate effect of base material combinations and thickness of welded joint on tensile properties at 4 K, tensile tests were conducted at 4 K by using tensile specimens taken from 40 mm thickness weld joints of four combinations and 200 mm thickness ones of two combinations of base materials. These weld joints were manufactured by one side narrow gap TIG welding with FMYJJ1. As the results, it was confirmed that yield and tensile strengths of welded joint at 4K were decreased with decreasing of nitrogen of base material, and there were no large distribution of strengths at 4 K along the thickness of welded joints of 200 mm thickness.

ITER magnet systems; From qualification to full scale construction

Nakajima, Hideo; Hemmi, Tsutomu; Iguchi, Masahide; Nabara, Yoshihiro; Matsui, Kunihiro; Chida, Yutaka; Kajitani, Hideki; Takano, Katsutoshi; Isono, Takaaki; Koizumi, Norikiyo; et al.

Proceedings of 24th IAEA Fusion Energy Conference (FEC 2012) (CD-ROM), 8 Pages, 2013/03

http://www-naweb.iaea.org/napc/physics/FEC/FEC2012/papers/578_ITR24.pdf

The ITER organization and 6 Domestic Agencies (DA) have been implementing the construction of ITER superconducting magnet systems. Four DAs have already started full scale construction of Toroidal Field (TF) coil conductors. The qualification of the radial plate manufacture has been completed, and JA and EU are ready for full scale construction. JA has qualified full manufacturing processes of the winding pack with a 1/3 prototype and made 2 full scale mock-ups of the basic segments of TF coil structure to optimize and industrialize the manufacturing process. Preparation and qualification of the full scale construction of the TF coil winding is underway by EU. Procurement of the manufacturing equipment is near completion and qualification of manufacturing processes has already started. The constructions of other components of the ITER magnet systems are also going well towards the main goal of the first plasma in 2020.

Development of structures for ITER toroidal field coil in Japan

Iguchi, Masahide; Chida, Yutaka; Takano, Katsutoshi; Kawano, Katsumi; Saito, Toru; Nakajima, Hideo; Koizumi, Norikiyo; Minemura, Toshiyuki*; Ogata, Hiroshige*; Ogawa, Tsuyoshi*; et al.

IEEE Transactions on Applied Superconductivity, 22(3), p.4203305_1 - 4203305_5, 2012/06

https://doi.org/10.1109/TASC.2011.2177795

Japan Atomic Energy Agency (JAEA) has responsibility to procure 19 structures for ITER toroidal field (TF) coils as in-kind components. JAEA plans to use materials specified in the material section of "Codes for Fusion Facilities; Rules on Superconducting Magnet Structure (2008)" issued by the Japan Society of Mechanical Engineers (JSME) in 2008. Large forged products were produced and their mechanical properties at 4K were evaluated. In addition, the following activities have been performed; (1) to optimize the design of each weld type identified in the manufacturing sequence, (2) to qualify typical welding procedure including repair, (3) to establish welding techniques other than narrow gap TIG welding with FMYJJ1, (4) to demonstrate the manufacturing procedures through manufacture of 1-m mockups and full-scale segments of TFC structure. This paper describes the results of material qualification and industrialization activities of manufacturing processes of ITER TFC structure.

Development of ITER TF coil in Japan

Koizumi, Norikiyo; Matsui, Kunihiro; Hemmi, Tsutomu; Takano, Katsutoshi; Chida, Yutaka; Iguchi, Masahide; Nakajima, Hideo; Shimada, Mamoru*; Osemochi, Koichi*; Makino, Yoshinobu*; et al.

IEEE Transactions on Applied Superconductivity, 22(3), p.4200404_1 - 4200404_4, 2012/06

https://doi.org/10.1109/TASC.2011.2176697

JAEA started sub- and full-scale trials to qualify and optimize manufacturing procedure of ITER TF coil from March, 2009. As major outcome of these trials, automatic winding system with accuracy in conductor length measurement of 0.01% has been established and the elongation of the conductor length due to heat treatment was measured to be 0.06%. To confirm validity of these outcomes, the authors carried out winding of a one-third scale dummy double pancake (DP), followed by its insulation and impregnation trial, and, in addition, heat treatment of one-third scale DP with real a TF conductor. The details about these trials are described in the other paper. The authors also performed trial manufacture of full scale RP and CPs for dummy double pancake, which will be made in near future. The full scale RP is manufactured by machining 10 segments in parallel to shorten machining duration and joining each segment by welding. In our trial manufacture of the full scale RP, hot-rolled SS316LN plates are machined to a final dimension, namely without additional material, and these segments are laser-welded. From these trials, manufacturing procedure of a thick hot-roll SS316LN plate is qualified and machining procedure is established, while more optimization may be necessary to achieve the required schedule and cost.

Validation of welding technology for ITER TF coil structures

Chida, Yutaka; Iguchi, Masahide; Takano, Katsutoshi; Nakajima, Hideo; Osemochi, Koichi*; Niimi, Kenichiro*; Tokai, Daisuke*; Gallix, R.*

Fusion Engineering and Design, 86(12), p.2900 - 2903, 2011/12

https://doi.org/10.1016/j.fusengdes.2011.06.004

TF coil structures, which support large electromagnetic force generated in TF coils under the cryogenic temperature (about 4K), are the mega welding structures composed of coil case and support structures made of high strength and high toughness stainless steel. JAEA started the study on welding trials for heavy thickness materials since 2008 and is planning of full scale mock-up model fabrication for main sub-components (1 set of inboard side and 1set of outboard side) in 2010 in order to investigate the technical issues for manufacturing of TF coil structures. This paper introduces the results on welding trials and status of full scale mock-up model fabrication to confirm the validity of welding technology and manufacturing design before fabricating actual products.

Data report of BWR post-CHF tests; Transient core thermal-hydraulic program (Contract research)

Iguchi, Tadashi; Ito, Hideo; Kiuchi, Toshio; Watanabe, Hironori; Kimura, Mamoru*; Anoda, Yoshinari

JAERI-Data/Code 2001-013, 502 Pages, 2001/03

JAERI-Data-Code-2001-013.pdf:32.38MB

no abstracts in English

Design of radial neutron spectrometer for ITER

Nishitani, Takeo; Iguchi, Tetsuo*; Ebisawa, Katsuyuki*; *; Kasai, Satoshi

JAERI-Tech 96-038, 29 Pages, 1996/09

JAERI-Tech-96-038.pdf:1.17MB

no abstracts in English

Fracture mechanics analysis of ITER toroidal field coil

Onodera, Osamu*; Iguchi, Masahide*; Saito, Masakatsu*; Hamada, Kazuya; Nakajima, Hideo; Okuno, Kiyoshi; Sugimoto, Makoto; Nakahira, Masataka; Kitamura, Kazunori; Takayanagi, Tadatoshi*; et al.

no journal, , 

no abstracts in English