Assessment of hydrogen embrittlement behavior in Al-Zn-Mg alloy through multi-modal 3D image-based simulation

Fujihara, Hiro*; Toda, Hiroyuki*; Ebihara, Kenichi; Kobayashi, Masakazu*; Mayama, Tsuyoshi*; Hirayama, Kyosuke*; Shimizu, Kazuyuki*; Takeuchi, Akihisa*; Uesugi, Masayuki*

International Journal of Plasticity, 174, p.103897_1 - 103897_22, 2024/03

https://doi.org/10.1016/j.ijplas.2024.103897

Hydrogen(H) embrittlement in high-strength aluminum(Al) alloys is a crucial problem. H accumulation at the interface of precipitates in Al alloy is considered to cause embrittlement. However, there is no quantitative knowledge regarding the interaction between H distribution and stress field near cracks. In this study, using a multi-modal three-dimensional image-based simulation combining the crystal plasticity finite element method and H diffusion analysis, we tried to capture the stress distribution near the crack, its influence on the H distribution, and the probability of crack initiation in the experimental condition. As a result, it was found that grain boundary cracks transition to quasi-cleavage cracks in the region where the cohesive energy of the semi-coherent interface of MgZn precipitates decreases due to H accumulation near the tip. We believe the present simulation method successfully bridges nanoscale delamination and macroscale brittle fracture.

Physical property investigation of gloves for glove boxes in nuclear fuel reprocessing plants; Physical properties of used gloves and estimation of its life-time

Yamamoto, Masahiko; Nishida, Naoki; Kobayashi, Daisuke; Nemoto, Ryo*; Hayashi, Hiroyuki*; Kitao, Takahiko; Kuno, Takehiko

JAEA-Technology 2023-004, 30 Pages, 2023/06

JAEA-Technology-2023-004.pdf:1.94MB

Glove-box gloves, that are used for handling nuclear fuel materials at the Tokai Reprocessing Plant (TRP) of the Japan Atomic Energy Agency, have an expiration date by internal rules. All gloves are replaced at a maximum of every 4-year. However, degrees of glove deterioration varies depending on its usage environment such as frequency, chemicals, and radiation dose. Therefore, physical properties such as tensile strength, elongation, hardness of gloves are measured and technical evaluation method for the glove life-time is established. It was found that gloves without any defects in its appearance have enough physical properties and satisfies the acceptance criteria values of new gloves. Thus, it was considered that the expired gloves could be used for total of 8-year, by adding 4-year of new glove life-time. In addition, the results of extrapolation by plotting the glove's physical properties versus the used years showed that the physical properties at 8-year is on the safer side than the reported physical properties of broken glove. Also, the data are not significantly different from the physical properties of the long-term storage glove (8 and 23 years). Based on these results, life-time of gloves at TRP is set to be 8-year. The frequency of glove inspections are not changed, and if any defects is found, the glove is promptly replaced. Thus, the risk related to glove usage is not increased. The cost of purchasing gloves, labor for glove replacement, and the amount of generated waste can be reduced by approximately 40%, respectively, resulting in more efficient and rationalized glove management.

Evaluation for updating the intra-bunch feedback at J-PARC main ring

Yoshimura, Nobuyuki*; Toyama, Takeshi*; Kobayashi, Aine*; Nakamura, Takeshi*; Okada, Masashi*; Shobuda, Yoshihiro; Nakaya, Tsuyoshi*

Proceedings of 19th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.936 - 941, 2023/01

https://www.pasj.jp/web_publish/pasj2022/proceedings/PDF/FRP0/FRP014.pdf

no abstracts in English

In-operando lithium-ion transport tracking in an all-solid-state battery

Kobayashi, Takane*; Onishi, Tsuyoshi*; Osawa, Takahito; Pratt, A.*; Tear, S.*; Shimoda, Susumu*; Baba, Hidetada*; Laitinen, M.*; Sajavaara, T.*

Small, 18(46), p.2204455_1 - 2204455_9, 2022/11

https://doi.org/10.1002/smll.202204455

An all-solid-state battery is a secondary battery that is charged and discharged by the transport of lithium ions between positive and negative electrodes. To fully realize the significant benefits of this battery technology, for example, higher energy densities, faster charging times, safer operation, it will be essential to understand how lithium ions are transported and distributed in the battery during operation. However, as the third lightest element, methods for quantitatively analyzing lithium during operation of an all-solid-state device are limited such that real time tracking of lithium transport has not yet been demonstrated. Here, we report that the transport of lithium ions in an all-solid-state half-cell was quantitatively tracked in near real time by utilizing a thermal neutron-induced nuclear reaction, utilizing lithium-6 as a tracer, and utilizing a high-intensity thermal neutron source. Furthermore, it is also mentioned that the migration mechanism and migration region of lithium ions in the solid electrolyte used could be determined by tracking the transport of lithium ions. From these results, it can be said that the development of all-solid-state batteries has entered a phase where further advances could be carried out while understanding the transport of lithium ions in the batteries. As a result, the research and development of all-solid-state batteries would be further accelerated.

Impedance reduction by a SiC-loaded flange and its application to the J-PARC main ring septum magnet

Kobayashi, Aine*; Toyama, Takeshi*; Nakamura, Takeshi*; Shobuda, Yoshihiro; Ishi, Koji*

Nuclear Instruments and Methods in Physics Research A, 1031, p.166515_1 - 166515_12, 2022/05

https://doi.org/10.1016/j.nima.2022.166515

The beam power of the main ring of the Japan Proton Accelerator Research Complex (J-PARC) is currently being increased. For high-power beam realization, it is essential to suppress the beam instability that limits the beam power and to estimate and enact countermeasures against the beam coupling impedance of individual devices. The fast-extraction (FX) septum magnet will be replaced with another magnet that copes with higher numbers of repetition cycles. Despite their different structures, both septa demonstrated a large impedance in estimates performed by the CST studio suite wake-field solver. The widely used taper impedance-reduction method would be effective but receives spatial constraints. By attaching a copper plate and SiC to the flange of the septum magnet, we could effectively reduce the impedance. The copper plate on the flange reduces the impedance below the cut-off frequency. Moreover, when SiC was loaded, the remaining impedance was three times lower than when using the copper plate alone. After applying this method to the new septum magnet, the maximum longitudinal impedance was reduced to 1% of the value without countermeasures, largely improving the beam stability condition. We also estimated the required thickness of SiC and the calorific value. This method saves space and is installed by simple attachment to the flange, regardless of the shape of the beam pipe. Therefore, it is also applicable to other devices.

Evaluation and countermeasures for impedance of fast extraction septa and fast extraction kickers at the J-PARC main ring

Kobayashi, Aine*; Toyama, Takeshi*; Nakamura, Takeshi*; Shobuda, Yoshihiro; Ishii, Koji*

Proceedings of 18th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.287 - 291, 2021/10

https://www.pasj.jp/web_publish/pasj2021/proceedings/PDF/MOP0/MOP022.pdf

no abstracts in English

Development of evaluation method for photocatalytic ability by ion chromatography combined with a flow-type reactor; Application to immobilized photocatalyst materials prepared by double-layer coating method

Sugita, Tsuyoshi; Kobayashi, Kentaro*; Yamazaki, Taiki*; Isaka, Mayu*; Itabashi, Hideyuki*; Mori, Masanobu*

Journal of Photochemistry and Photobiology A; Chemistry, 400, p.112662_1 - 112662_8, 2020/09

https://doi.org/10.1016/j.jphotochem.2020.112662

In this study, we developed an in-line photocatalytic performance evaluation system in which a flow reactor was connected to the ion chromatography to accurately evaluate the performance of the photocatalyst. This system was used to evaluate the photocatalyst supported by the two-layer support method on the substrate, such as glass beads. The performance of the photocatalyst was evaluated using dimethyl sulfoxide (DMSO), and it was possible to monitor the decomposition of DMSO by UV and the formation of by-products, such as methane sulfonate (MSO) and sulfate (SA). This system can be expected to be useful not only for evaluating the decomposition performance of an object using a photocatalyst but also for evaluating the byproducts.

Analysis of collective instabilities of uneven filled beams including long range wake fields using an IIR filter

Toyama, Takeshi*; Kobayashi, Aine*; Nakamura, Takeshi*; Shobuda, Yoshihiro

Proceedings of 17th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.689 - 692, 2020/09

no abstracts in English

Mechanism of palladium(II) adsorption from nitric acid solutions by a styrene-divinylbenzene copolymer functionalized with -trimethylglycine

Suzuki, Tomoya*; Narita, Hirokazu*; Ogata, Takeshi*; Suzuki, Hideya; Matsumura, Tatsuro; Kobayashi, Toru; Shiwaku, Hideaki; Yaita, Tsuyoshi

Solvent Extraction Research and Development, Japan, 26(1), p.11 - 19, 2019/06

https://doi.org/10.15261/serdj.26.11

The ability of AMP03, a styrene-divinylbenzene copolymer functionalized with -trimethylglycine moieties, to adsorb Pd(II) from HNO solutions was investigated to elucidate the affinity of -trimethylglycine for Pd(II). In the present study, we investigated the mechanism of Pd(II) adsorption by AMP03 by means of adsorption experiments, Fourier Transform Infrared (FT-IR) spectroscopy, and Extended X-ray Absorption Fine Structure (EXAFS) spectroscopy.

Speciation of ruthenium(III) chloro complexes in hydrochloric acid solutions and their extraction characteristics with an amide-containing amine compound

Suzuki, Tomoya*; Ogata, Takeshi*; Tanaka, Mikiya*; Kobayashi, Toru; Shiwaku, Hideaki; Yaita, Tsuyoshi; Narita, Hirokazu*

Metals, 8(7), p.558_1 - 558_10, 2018/07

AA2018-0670.pdf:2.11MB

https://doi.org/10.3390/met8070558

The refining of platinum group metals is based mainly on solvent extraction methods, whereas Ru is selectively recovered by distillation as RuO. Replacement of distillation byextraction is expected to simplify the purification process. To develop an effective extraction system for Ru, we analyzed the Ru species in HCl with UV-Vis and EXAFS spectroscopies, and we examined the properties of Ru extracted with N-2-ethylhexyl-bis(N-di-2-ethylhexyl-ethylamide) amine (EHBAA). EXAFS and UV-Vis spectra of Ru in HCl solutions revealed that the predominant Ru species in 0.5-10 M HCl solutions changed from [RuCl(HO)] to [RuCl] with the HCl concentration. The extraction percentages of Ru in the EHBAA system increased with increasing HCl concentration, reached 80% at [HCl] = 5 M, and decreased athigher HCl concentrations. EXAFS analysis of the extracted complex indicated that the Ru had 5 Cl and 1 HO in its inner coordination sphere. The similarity of the dependence on HCl concentrations of the extraction in the EHBAA system and the distribution profile of [RuCl(HO)] on [RuCl(HO)] suggested that the EHBAA extracted the pentachlorido species.