Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Asano, Shiro*; Okuyama, Toshihisa*; Onawa, Toshio*; Yanagi, Yutaka*; Ejiri, Mitsuru*; Kanahara, Toshio*; Ichihashi, Koji*; Kikuchi, Atsushi*; Mizumaki, Shoichi*; Masaki, Kei; et al.
Fusion Engineering and Design, 86(9-11), p.1816 - 1820, 2011/10
Times Cited Count：12 Percentile：66.68(Nuclear Science & Technology)The real vacuum vessel (VV) manufacturing of JT-60SA has started since Nov. 2009 at Toshiba. Prior to starting manufacturing, fundamental welding R&Ds had been performed by three stages. In the first stage, primary tests for screening welding method were performed. In the second stage, the trial welding for 1m-long straight and curved double shell samples were conducted. The dependences of welding quality and distortion on the welding conditions, such as arc voltage and current, setting accuracy, welding sequence, the shape of grooves, etc. were measured. In addition, welding condition with low heat input was explored. In the last stage, fabrication sequence was confirmed and established by the trial manufacturing of the 20
upper half mock-up. This poster presents the R&D results obtained in the first and second stages.
Higashijima, Satoru; Sakurai, Shinji; Suzuki, Satoshi; Yokoyama, Kenji; Kashiwa, Yoshitoshi; Masaki, Kei; Shibama, Yusuke; Takechi, Manabu; Shibanuma, Kiyoshi; Sakasai, Akira; et al.
Fusion Engineering and Design, 84(2-6), p.949 - 952, 2009/06
Times Cited Count：9 Percentile：53.16(Nuclear Science & Technology)An upgrading device of JT-60 tokamak with fully superconducting coils (JT-60SA) is constructed under both the Japanese domestic program and the international program "Broader Approach". The maximum heat flux to JT-60SA divertor is estimated to 15 MW/m
for 100 s, and a monoblock-type CFC divertor armor is promising. The JT-60SA armor consists of CFC monoblocks, a cooling CuCrZr screw-tube, and a thin OFHC-Cu buffer layer, and the brazed joints are essential for the armor. Metalization inside CFC monoblock is applied for further improvement, and we confirmed again that the mock-up has heat removal capability in excess of ITER requirement. For optimization of the fabrication method and understanding of the production yield, the mock-ups corresponding to quantity produced in one furnace is also produced, and the half of the mock-ups could remove 15 MW/m as required. This summarizes the recent progress of design and mock-up test results for JT-60SA divertor armor.
Matsukawa, Makoto; Kikuchi, Mitsuru; Fujii, Tsuneyuki; Fujita, Takaaki; Hayashi, Takao; Higashijima, Satoru; Hosogane, Nobuyuki; Ikeda, Yoshitaka; Ide, Shunsuke; Ishida, Shinichi; et al.
Fusion Engineering and Design, 83(7-9), p.795 - 803, 2008/12
Times Cited Count：17 Percentile：72.65(Nuclear Science & Technology)no abstracts in English
Ninomiya, Hiromasa; Akiba, Masato; Fujii, Tsuneyuki; Fujita, Takaaki; Fujiwara, Masami*; Hamamatsu, Kiyotaka; Hayashi, Nobuhiko; Hosogane, Nobuyuki; Ikeda, Yoshitaka; Inoue, Nobuyuki; et al.
Journal of the Korean Physical Society, 49, p.S428 - S432, 2006/12
To contribute DEMO and ITER, the design to modify the present JT-60U into superconducting coil machine, named National Centralized Tokamak (NCT), is being progressed under nationwide collaborations in Japan. Mission, design and strategy of this NCT program is summarized.
Kikuchi, Mitsuru; Tamai, Hiroshi; Matsukawa, Makoto; Fujita, Takaaki; Takase, Yuichi*; Sakurai, Shinji; Kizu, Kaname; Tsuchiya, Katsuhiko; Kurita, Genichi; Morioka, Atsuhiko; et al.
Nuclear Fusion, 46(3), p.S29 - S38, 2006/03
Times Cited Count：13 Percentile：41.68(Physics, Fluids & Plasmas)The National Centralized Tokamak (NCT) facility program is a domestic research program for advanced tokamak research to succeed JT-60U incorporating Japanese university accomplishments. The mission of NCT is to establish high beta steady-state operation for DEMO and to contribute to ITER. The machine flexibility and mobility is pursued in aspect ratio and shape controllability, feedback control of resistive wall modes, wide current and pressure profile control capability for the demonstration of the high-b steady state.
Tsuchiya, Katsuhiko; Akiba, Masato; Azechi, Hiroshi*; Fujii, Tsuneyuki; Fujita, Takaaki; Fujiwara, Masami*; Hamamatsu, Kiyotaka; Hashizume, Hidetoshi*; Hayashi, Nobuhiko; Horiike, Hiroshi*; et al.
Fusion Engineering and Design, 81(8-14), p.1599 - 1605, 2006/02
Times Cited Count：1 Percentile：9.94(Nuclear Science & Technology)no abstracts in English
plasma operationTamai, Hiroshi; Akiba, Masato; Azechi, Hiroshi*; Fujita, Takaaki; Hamamatsu, Kiyotaka; Hashizume, Hidetoshi*; Hayashi, Nobuhiko; Horiike, Hiroshi*; Hosogane, Nobuyuki; Ichimura, Makoto*; et al.
Nuclear Fusion, 45(12), p.1676 - 1683, 2005/12
Times Cited Count：15 Percentile：45.44(Physics, Fluids & Plasmas)Design studies are shown on the National Centralized Tokamak facility. The machine design is carried out to investigate the capability for the flexibility in aspect ratio and shape controllability for the demonstration of the high-beta steady state operation with nation-wide collaboration, in parallel with ITER towards DEMO. Two designs are proposed and assessed with respect to the physics requirements such as confinement, stability, current drive, divertor, and energetic particle confinement. The operation range in the aspect ratio and the plasma shape is widely enhanced in consistent with the sufficient divertor pumping. Evaluations of the plasma performance towards the determination of machine design are presented.
Sakasai, Akira; Ishida, Shinichi; Matsukawa, Makoto; Akino, Noboru; Ando, Toshinari*; Arai, Takashi; Ezato, Koichiro; Hamada, Kazuya; Ichige, Hisashi; Isono, Takaaki; et al.
Nuclear Fusion, 44(2), p.329 - 334, 2004/02
no abstracts in English
Sakasai, Akira; Ishida, Shinichi; Matsukawa, Makoto; Akino, Noboru; Ando, Toshinari*; Arai, Takashi; Ezato, Koichiro; Hamada, Kazuya; Ichige, Hisashi; Isono, Takaaki; et al.
Nuclear Fusion, 44(2), p.329 - 334, 2004/02
Times Cited Count：7 Percentile：22.88(Physics, Fluids & Plasmas)no abstracts in English
Tamai, Hiroshi; Matsukawa, Makoto; Kurita, Genichi; Hayashi, Nobuhiko; Urata, Kazuhiro*; Miura, Yushi; Kizu, Kaname; Tsuchiya, Katsuhiko; Morioka, Atsuhiko; Kudo, Yusuke; et al.
Plasma Science and Technology, 6(1), p.2141 - 2150, 2004/02
Times Cited Count：2 Percentile：6.49(Physics, Fluids & Plasmas)The dominant issue for the the modification program of JT-60 (JT-60SC) is to demonstrate the steady state reactor relevant plasma operation. Physics design on plasma parameters, operation scenarios, and the plasma control method are investigated for the achievement of high-. Engineering design and the R&D on the superconducting magnet coils, radiation shield, and vacuum vessel are performed. Recent progress in such physics and technology developments is presented.
Saigusa, Mikio*; Kikuchi, Yusuke*; Takei, Nahoko*; Kanazawa, Sadayoshi*; Kasugai, Atsushi; Sakamoto, Keishi; Imai, Tsuyoshi
Fusion Engineering and Design, 53(1-4), p.505 - 510, 2001/01
Times Cited Count：11 Percentile：61.93(Nuclear Science & Technology)no abstracts in English
Saigusa, Mikio*; Takei, Nahoko*; Kanazawa, Sadayoshi*; Kikuchi, Yusuke*; Kasugai, Atsushi; Sakamoto, Keishi; Imai, Tsuyoshi
Journal of Plasma and Fusion Research SERIES, Vol.3, p.383 - 386, 2000/00
no abstracts in English
Okamoto, Masaaki*; Yamada, Takashi*; Kikuchi, Yusuke*; Ono, Noriyasu*; Takamura, Shuichi*; Uesugi, Yoshihiko*; Ozeki, Takahisa; Kawano, Yasunori; Sugihara, Masayoshi
no journal, ,
no abstracts in English
Alonso, J.*; Botija, J.*; Medrano, M.*; Rincon, E.*; Fernandez, P.*; Soleto, A.*; Kikuchi, Mitsuru; Matsukawa, Makoto; Masaki, Kei; Shibama, Yusuke
no journal, ,
no abstracts in English
Asano, Shiro*; Ejiri, Mitsuru*; Yanagi, Yutaka*; Ichihashi, Koji*; Kikuchi, Atsushi*; Mizumaki, Shoichi*; Okuyama, Toshihisa*; Masaki, Kei; Shibama, Yusuke; Katayama, Masahiro*; et al.
no journal, ,
no abstracts in English
