Effects of helium on irradiation response of reduced-activation ferritic-martensitic steels; Using nickel isotopes to simulate fusion neutron response

Kim, B. K.*; Tan, L.*; Sakasegawa, Hideo; Parish, C. M.*; Zhong, W.*; Tanigawa, Hiroyasu*; Kato, Yutai*

Journal of Nuclear Materials, 545, p.152634_1 - 152634_12, 2021/03

https://doi.org/10.1016/j.jnucmat.2020.152634

Hydrogen behavior in primary precipitate of F82H steel; Atomistic calculation based on the density functional theory

Watanabe, Yoshiyuki; Iwakiri, Hirotomo*; Murayoshi, Norihiko*; Kato, Daiji*; Tanigawa, Hiroyasu

Plasma and Fusion Research (Internet), 10, p.1205086_1 - 1205086_2, 2015/12

https://doi.org/10.1585/pfr.10.1205086

In this paper, formation energy of isolated hydrogen atom in CrC has been theoretically investigated with atomistic calculation based on the density functional theory. The lowest calculated formation energy of a hydrogen atom is -0.48 eV with a trigonal bipyramidal configuration surrounded by five regular Cr lattice atoms. A comparison of the formation energy of hydrogen atom in bcc-iron may indicate that hydrogen atoms in F82H steel are more energetically favorable in CrC-based precipitate rather than Fe-based matrix, leading to an increase of the tritium retention in the precipitate.

Modification of vacuum plasma sprayed tungsten coating on reduced activation ferritic/martensitic steels by friction stir processing

Tanigawa, Hiroyasu; Ozawa, Kazumi; Morisada, Yoshiaki*; Noh, S.*; Fujii, Hidetoshi*

Fusion Engineering and Design, 98-99, p.2080 - 2084, 2015/10

https://doi.org/10.1016/j.fusengdes.2015.04.059

The vacuum plasma spray (VPS) technique has been investigated as the most practical method to form Tungsten (W) layer as a plasma facing material in fusion devices. The issues are the thermal conductivity and the strength of VPS-W, i.e., the thermal conductivity of VPS-W were significantly lower than that of the bulk W, and the hardness of VPS-W is much less than that of the bulk W. These are mainly caused by the porous structure of VPS-W. In order to solve these issues, friction stir processing (FPS) was applied on VPS-W in this study. It was suggested that FSP can contribute to significant improvement both in mechanical and thermal properties of VPS-W coating.

Evaluation of damage accumulation behavior and strength anisotropy of NITE SiC/SiC composites by acoustic emission, digital image correlation and electrical resistivity monitoring

Nozawa, Takashi; Ozawa, Kazumi; Asakura, Yuki*; Koyama, Akira*; Tanigawa, Hiroyasu

Journal of Nuclear Materials, 455(1-3), p.549 - 553, 2014/12

https://doi.org/10.1016/j.jnucmat.2014.08.043

SiC/SiC composite is a promising candidate material of fusion DEMO reactor. This paper aims to identify its damage tolerance and strength anisotropy by various characterization techniques such as acoustic emission (AE) monitoring, electrical resistivity (ER) measurement, and digital image correlation (DIC). The AE results identified that damage accumulation initiated prior to the proportional limit stress (PLS) by both tensile and compressive loadings for 2D composites. The preliminary AE waveform analysis implied that this AE detect strength corresponds to initiation of micro-cracking but the stress-strain curve shows further linearity due to the strong interfacial friction. Then fiber sliding occurred near the PLS, followed by the non-linearlity of the curve. The preliminary tensile test results using a notched specimen also suggest notch insensitivity of the composites in any loading directions. The detailed failure mechanism will eventually be discussed with ER and DIC results.

R&D status on water cooled ceramic breeder blanket technology

Enoeda, Mikio; Tanigawa, Hisashi; Hirose, Takanori; Nakajima, Motoki; Sato, Satoshi; Ochiai, Kentaro; Konno, Chikara; Kawamura, Yoshinori; Hayashi, Takumi; Yamanishi, Toshihiko; et al.

Fusion Engineering and Design, 89(7-8), p.1131 - 1136, 2014/10

https://doi.org/10.1016/j.fusengdes.2014.01.035

The development of a Water Cooled Ceramic Breeder (WCCB) Test Blanket Module (TBM) is being performed as one of the most important steps toward DEMO blanket in Japan. Regarding the fabrication technology development using F82H, the fabrication of a real scale mockup of the back wall of TBM was completed. Also the assembling of the complete box structure of the TBM mockup and planning of the pressurization testing was studied. The development of advanced breeder and multiplier pebbles for higher chemical stability was performed for future DEMO blanket application. From the view point of TBM test result evaluation and DEMO blanket performance design, the development of the blanket tritium simulation technology, investigation of the TBM neutronics measurement technology and the evaluation of tritium production and recovery test using D-T neutron in the Fusion Neutronics Source (FNS) facility has been performed.

Compatibility of Ni and F82H with liquid Pb-Li under rotating flow

Kanai, Akihiko*; Park, C.*; Noborio, Kazuyuki*; Kasada, Ryuta*; Konishi, Satoshi*; Hirose, Takanori; Nozawa, Takashi; Tanigawa, Hiroyasu

Fusion Engineering and Design, 89(7-8), p.1653 - 1657, 2014/10

https://doi.org/10.1016/j.fusengdes.2014.03.008

Radiation-induced effects in physical properties of materials, 2-6; Evaluation of irradiation creep for F82H steel by using pressurized tubes

Ando, Masami; Nozawa, Takashi; Hirose, Takanori; Tanigawa, Hiroyasu

Purazuma, Kaku Yugo Gakkai-Shi, 90(1), p.64 - 67, 2014/01

http://ci.nii.ac.jp/naid/110009688791

Reduced activation ferritic/martensitic steel (RAFM) is a candidate for the material of DEMO blanket structure. The irradiation creep behavior of F82H and JLF-1 steel has been measured at 300, 400 and 500C up to 5 dpa using helium-pressurized creep tubes irradiated in HFIR. These tubes were pressurized with helium to hoop stress levels of 0400 MPa at the irradiation temperature. The results for F82H and JLF-1 with a 400 MPa hoop stress detected small creep strains ( 0.25%) after irradiation at 300C. Irradiation creep rate (creep strain/dose) was tendency to be a similar behavior for high-dose irradiated RAFM specimens in FFTF. In this paper, a procedure of irradiation creep test & evaluation was also summarized.

Microsegregation in a F82H plate

Sakasegawa, Hideo; Tanigawa, Hiroyasu

Journal of Nuclear Materials, 442(1-3), p.S18 - S22, 2013/11

https://doi.org/10.1016/j.jnucmat.2013.01.322

Through the Broader Approach (BA) activity in Japan, F82H-BA07 heat of 5 tons prepared applying electrosrag remelting (ESR) has been studied as a step toward a larger-scale melting about 20 tons. From the result of elemental mapping images using electron probe microanalysis (EPMA), micro-segregation of at least four metallic elements such as chromium, tungsten, vanadium and manganese was found as stripes parallel to the hot rolling direction. In the case of tungsten segregation, the maximum difference of content was about 1.0 wt% between the observed stripes. This difference could cause differences in nano-metric structures between stripes, and affect mechanical properties. In this presentation, we discuss how much micro-segregation should be decreased considering effects of micro-segregation on nano-metric structures and mechanical properties in addition to the result of optimization of homogenizing condition.

Re-defining failure envelopes for silicon carbide composites based on damage process analysis by acoustic emission

Nozawa, Takashi; Ozawa, Kazumi; Tanigawa, Hiroyasu

Fusion Engineering and Design, 88(9-10), p.2543 - 2546, 2013/10

https://doi.org/10.1016/j.fusengdes.2013.05.054

A SiC/SiC composite is a promising candidate for a fusion DEMO blanket. Due to the inherent quasi-ductile failure of composites, determining failure scenario for this class of composites is undoubtedly important to develop design codes in practical use of them. This study aims to evaluate the failure behavior of the quasi-ductile SiC/SiC composites to provide a strength map. For this purpose, detailed tensile, compressive and in-plane shear failure behaviors were evaluated by the acoustic emission (AE) technique. The AE results distinguished damage accumulation processes by wavelet analysis. Of particular emphasis is that matrix cracking occurred prior to the PLS by both tensile and compressive loadings because the rough-surface of SiC fibers resulted in the strong frictional stress at the fiber/matrix (F/M) interface. In this paper, an updated failure envelope will be provided by referring the actual matrix cracking stresses as more realistic and reasonable failure criteria.

A Feasible DEMO blanket concept based on water cooled solid breeder

Someya, Yoji; Tobita, Kenji; Uto, Hiroyasu; Hoshino, Kazuo; Asakura, Nobuyuki; Nakamura, Makoto; Tanigawa, Hisashi; Enoeda, Mikio; Tanigawa, Hiroyasu; Nakamichi, Masaru; et al.

Proceedings of 24th IAEA Fusion Energy Conference (FEC 2012) (CD-ROM), 8 Pages, 2013/03

This paper presents the conceptual design of a blanket with simplified structure whose interior consists of the mixture of breeder and multiplier pebble bed, cooling tubes and support for them only. Neutronics calculation indicated that the blanket satisfies a self-sufficient production of tritium. An important finding is that little decrease is seen in TBR even when the gap between neighboring blanket modules is as wide as 0.03 m. This means that blanket modules can be arranged with such a significant clearance gap without sacrifice of tritium production. On the other hand, the thickness of blanket housing is important from the viewpoint of safety. The blanket housing may rupture when the cooling pipe in the blanket is tearing, because thickness of structure materials is thin as 22 mm. This thickness is expected to maintain to 8 MPa in the steam pressure. Finally, the blanket housing, and aspect ratio of blanket shape is proposed in consideration of TBR, and engineering problem such as maintenance and manufacture are discussed.