Quantitatively evaluating respective contribution of austenite and deformation-induced martensite to flow stress, plastic strain, and strain hardening rate in tensile deformed TRIP steel

Mao, W.; Gao, S.*; Gong, W.; Bai, Y.*; Harjo, S.; Park, M.-H.*; Shibata, Akinobu*; Tsuji, Nobuhiro*

Acta Materialia, 256, p.119139_1 - 119139_16, 2023/09

https://doi.org/10.1016/j.actamat.2023.119139

Transformation-induced plasticity (TRIP)-assisted steels exhibit an excellent combination of strength and ductility due to enhanced strain hardening rate associated with deformation-induced martensitic transformation (DIMT). Quantitative evaluation on the role of DIMT in strain hardening behavior of TRIP-assisted steels and alloys can provide guidance for designing advanced materials with strength and ductility synergy, which is, however, difficult since the phase composition keeps changing and both stress and plastic strain are dynamically partitioned among constituent phases during deformation. In the present study, tensile deformation with neutron diffraction measurement was performed on an Fe-24Ni-0.3C (wt.%) TRIP-assisted austenitic steel. The analysis method based on stress partitioning and phase fractions measured by neutron diffraction was proposed, by which the tensile flow stress and the strain hardening rate of the specimen were resolved into factors associated with each phase, i.e., the austenite matrix, deformation-induced martensite, and the transformation rate of DIMT after differentiation, and then the role of each factor in the global strain hardening behavior was discussed. In addition, the plastic strain partitioning between austenite and martensite was indirectly estimated using the dislocation density measured by diffraction profile analysis, which constructed the full picture of stress and strain partitioning between austenite and martensite in the material. The results suggested that both the transformation rate and the phase stress borne by the deformation-induced martensite played important roles in the global tensile properties of the material. The proposed decomposition analysis method could be widely applied to investigating mechanical behavior of multi-phase alloys exhibiting the TRIP phenomenon.

Unexpected dynamic transformation from phase to phase in zirconium alloy revealed by in-situ neutron diffraction during high temperature deformation

Guo, B.*; Mao, W.; Chong, Y.*; Shibata, Akinobu*; Harjo, S.; Gong, W.; Chen, H.*; Jonas, J. J.*; Tsuji, Nobuhiro*

Acta Materialia, 242, p.118427_1 - 118427_11, 2023/01

https://doi.org/10.1016/j.actamat.2022.118427

Modelling of the LTDE-SD radionuclide diffusion experiment in crystalline rock at the sp Hard Rock Laboratory (Sweden)

Soler, J. M.*; Meng, S.*; Moreno, L.*; Neretnieks, I.*; Liu, L.*; Keklinen, P.*; Hokr, M.*; ha, J.*; Vetenk, A.*; Reimitz, D.*; et al.

Geologica Acta, 20(7), 32 Pages, 2022/07

https://doi.org/10.1344/GeologicaActa2022.20.7

Task 9B of the SKB Task Force on Modelling of Groundwater Flow and Transport of Solutes in fractured rock focused on the modelling of experimental results from the LTDE-SD in situ tracer test performed at the sp Hard Rock Laboratory in Sweden. Ten different modelling teams provided results for this exercise, using different concepts and codes. Three main types of modelling approaches were used: (1) analytical solutions to the transport-retention equations, (2) continuum-porous-medium numerical models, and (3) microstructure-based models accounting for small-scale heterogeneity (i.e. mineral grains and microfracture distributions). The modelling by the different teams allowed the comparison of many different model concepts, especially in terms of potential zonations of rock properties (porosity, diffusion, sorption), such as the presence of a disturbed zone at the rock and fracture surface, the potential effects of micro- and cm-scale fractures.

Effective grain size refinement of an Fe-24Ni-0.3C metastable austenitic steel by a modified two-step cold rolling and annealing process utilizing the deformation-induced martensitic transformation and its reverse transformation

Mao, W.; Gao, S.*; Bai, Y.*; Park, M.-H.*; Shibata, Akinobu*; Tsuji, Nobuhiro*

Journal of Materials Research and Technology, 17, p.2690 - 2700, 2022/03

https://doi.org/10.1016/j.jmrt.2022.02.031

Metastable austenitic steels having ultrafine grained (UFG) microstructures can be fabricated by conventional cold rolling and annealing processes by utilizing the deformation-induced martensitic transformation during cold rolling and its reverse transformation to austenite upon annealing. However, such processes are not applicable when the austenite has high mechanical stability against deformation-induced martensitic transformation, since there is no sufficient amount of martensite formed during cold rolling. In the present study, a two-step cold rolling and annealing process was applied to an Fe-24Ni-0.3C metastable austenitic steel having high mechanical stability. Prior to the cold rolling, a repetitive subzero treatment and reverse annealing treatment were applied. Such a treatment dramatically decreased the mechanical stability of the austenite and greatly accelerated the formation of deformation-induced martensite during the following cold rolling processes. As a result, the grain refinement was significantly promoted, and a fully recrystallized specimen with a mean austenite grain size of 0.5 mm was successfully fabricated, which exhibited both high strength and high ductility.

Half-integer Shapiro steps in strong ferromagnetic Josephson junctions

Yao, Y.*; Cai, R.*; Yang, S.-H.*; Xing, W.*; Ma, Y.*; Mori, Michiyasu; Ji, Y.*; Maekawa, Sadamichi; Xie, X.-C.*; Han, W.*

Physical Review B, 104(10), p.104414_1 - 104414_6, 2021/09

https://doi.org/10.1103/PhysRevB.104.104414

Coordination number regulation of molybdenum single-atom nanozyme peroxidase-like specificity

Wang, Y.*; Jia, G.*; Cui, X.*; Zhao, X.*; Zhang, Q.*; Gu, L.*; Zheng, L.*; Li, L. H.*; Wu, Q.*; Singh, D. J.*; et al.

Chem, 7(2), p.436 - 449, 2021/02

https://doi.org/10.1016/j.chempr.2020.10.023

neutron diffraction study on the deformation of a TRIP-assisted multi-phase steel composed of ferrite, austenite and martensite

Lavakumar, A.*; Park, M. H.*; Gao, S.*; Shibata, Akinobu*; Okitsu, Yoshitaka*; Gong, W.; Harjo, S.; Tsuji, Nobuhiro*

IOP Conference Series; Materials Science and Engineering, 580, p.012036_1 - 012036_6, 2019/09

https://doi.org/10.1088/1757-899X/580/1/012036

Rechargeable batteries based on stable redox reactions of disulfide included in a metal-organic framework as ligands

Shimizu, Takeshi*; Wang, H.*; Tanifuji, Naoki*; Matsumura, Daiju; Yoshimura, Masashi*; Nakanishi, Koji*; Ota, Toshiaki*; Yoshikawa, Hirofumi*

Chemistry Letters, 47(5), p.678 - 681, 2018/05

https://doi.org/10.1246/cl.180121

Determination of fusion barrier distributions from quasielastic scattering cross sections towards superheavy nuclei synthesis

Tanaka, Taiki*; Narikiyo, Yoshihiro*; Morita, Kosuke*; Fujita, Kunihiro*; Kaji, Daiya*; Morimoto, Koji*; Yamaki, Sayaka*; Wakabayashi, Yasuo*; Tanaka, Kengo*; Takeyama, Mirei*; et al.

Journal of the Physical Society of Japan, 87(1), p.014201_1 - 014201_9, 2018/01

https://doi.org/10.7566/JPSJ.87.014201

Excitation functions of quasielastic scattering cross sections for the Ca + Pb, Ti + Pb, and Ca + Cm reactions were successfully measured by using the gas-filled recoil-ion separator GARIS. Fusion barrier distributions were extracted from these data, and compared with the coupled-channels calculations. It was found that the peak energies of the barrier distributions for the Ca + Pb and Ti + Pb systems coincide with those of the 2n evaporation channel cross sections for the systems, while that of the Ca + Cm is located slightly below the 4n evaporation ones. This results provide us helpful information to predict the optimum beam energy to synthesize superheavy nuclei.

Study of the reaction Ca + Cm Lv at RIKEN-GARIS

Kaji, Daiya*; Morita, Kosuke*; Morimoto, Koji*; Haba, Hiromitsu*; Asai, Masato; Fujita, Kunihiro*; Gan, Z.*; Geissel, H.*; Hasebe, Hiroo*; Hofmann, S.*; et al.

Journal of the Physical Society of Japan, 86(3), p.034201_1 - 034201_7, 2017/03

https://doi.org/10.7566/JPSJ.86.034201

The fusion reaction of Ca + Cm Lv was studied using the gas-filled recoil-ion separator GARIS at RIKEN. A total of seven and spontaneous-fission decay chains were observed, which would originate from the reaction products of the element 116, Lv and Lv. Decay properties observed in the chains are in good agreement with the previously published ones. However, one of the chains showed a discrepancy, indicating the new spontaneous-fission branch in Cn or the production of the new isotope Lv.