neutron diffraction revealing the achievement of excellent combination of strength and ductility in metastable austenitic steel by grain refinement

Mao, W.; Gong, W.; Harjo, S.; Morooka, Satoshi; Gao, S.*; Kawasaki, Takuro; Tsuji, Nobuhiro*

Journal of Materials Science & Technology, 176, p.69 - 82, 2024/03

https://doi.org/10.1016/j.jmst.2023.07.036

The yield stress of Fe-24Ni-0.3C (wt.%) metastable austenitic steel increased 3.5 times (158 551 MPa) when the average grain size decreased from 35 m (coarse-grained [CG]) to 0.5 m (ultrafine-grained [UFG]), whereas the tensile elongation was kept large (0.87 0.82). neutron diffraction measurements of the CG and UFG Fe-24Ni-0.3C steels were performed during tensile deformation at room temperature to quantitatively elucidate the influence of grain size on the mechanical properties and deformation mechanisms. The initial stages of plastic deformation in the CG and UFG samples were dominated by dislocation slip, with deformation-induced martensitic transformation (DIMT) also occurring in the later stage of deformation. Results show that grain refinement increases the initiation stress of DIMT largely and suppresses the rate of DIMT concerning the strain, which is attributed to the following effects. (i) Grain refinement increased the stabilization of austenite and considerably delayed the initiation of DIMT in the 111//LD (LD: loading direction) austenite grains, which were the most stable grains for DIMT. As a result, most of the 111//LD austenite grains in the UFG specimens failed to transform into martensite. (ii) Grain refinement also suppressed the autocatalytic effect of the martensitic transformation. Nevertheless, the DIMT with the low transformation rate in the UFG specimen was more efficient in increasing the flow stress and more appropriate to maintain uniform deformation than that in the CG specimen during deformation. The above phenomena mutually contributed to the excellent combination of strength and ductility of the UFG metastable austenitic steel.

Hierarchical deformation heterogeneity during Lders band propagation in an Fe-5Mn-0.1C medium Mn steel clarified through scanning electron microscopy

Koyama, Motomichi*; Yamashita, Takayuki*; Morooka, Satoshi; Yang, Z.*; Varanasi, R. S.*; Hojo, Tomohiko*; Kawasaki, Takuro; Harjo, S.

Tetsu To Hagane, 110(3), p.205 - 216, 2024/02

https://doi.org/10.2355/tetsutohagane.TETSU-2023-052

Martensitic transformation behavior of Fe-Ni-C alloys monitored by neutron diffraction during cryogenic cooling

Yamashita, Takayuki*; Harjo, S.; Kawasaki, Takuro; Morooka, Satoshi; Gong, W.; Fujii, Hidetoshi*; Tomota, Yo*

ISIJ International, 64(2), p.192 - 201, 2024/01

https://doi.org/10.2355/isijinternational.ISIJINT-2023-208

Lattice parameters of austenite and martensite during transformation for Fe-18Ni alloy investigated through neutron diffraction

Gong, W.; Harjo, S.; Tomota, Yo*; Morooka, Satoshi; Kawasaki, Takuro; Shibata, Akinobu*; Tsuji, Nobuhiro*

Acta Materialia, 250, p.118860_1 - 118860_16, 2023/05

https://doi.org/10.1016/j.actamat.2023.118860

Actual stress analysis of small-bore butt-welded pipe by complementary use of synchrotron X-rays and neutrons

Suzuki, Kenji*; Miura, Yasufumi*; Shiro, Ayumi*; Toyokawa, Hidenori*; Saji, Choji*; Shobu, Takahisa; Morooka, Satoshi

Zairyo, 72(4), p.316 - 323, 2023/04

https://doi.org/10.2472/jsms.72.316

Microstructure and plasticity evolution during Lders deformation in an Fe-5Mn-0.1C medium-Mn steel

Koyama, Motomichi*; Yamashita, Takayuki*; Morooka, Satoshi; Sawaguchi, Takahiro*; Yang, Z.*; Hojo, Tomohiko*; Kawasaki, Takuro; Harjo, S.

ISIJ International, 62(10), p.2036 - 2042, 2022/10

https://doi.org/10.2355/isijinternational.ISIJINT-2021-510

Revisit deformation behavior of lath martensite

Harjo, S.; Gong, W.; Kawasaki, Takuro; Morooka, Satoshi; Yamashita, Takayuki*

ISIJ International, 62(10), p.1990 - 1999, 2022/10

https://doi.org/10.2355/isijinternational.ISIJINT-2022-207

Influence of shape of deformed rebar on bond performance of reinforced concrete

Kobayashi, Kensuke*; Yasue, Ayumu*; Morooka, Satoshi; Kanematsu, Manabu*

Konkurito Kogaku Nenji Rombunshu (DVD-ROM), 44(1), p.208 - 213, 2022/07

no abstracts in English

Volatilization of BC control rods in Fukushima Daiichi nuclear reactors during meltdown; B-Li isotopic signatures in cesium-rich microparticles

Fueda, Kazuki*; Takami, Ryu*; Minomo, Kenta*; Morooka, Kazuya*; Horie, Kenji*; Takehara, Mami*; Yamasaki, Shinya*; Saito, Takumi*; Shiotsu, Hiroyuki; Onuki, Toshihiko*; et al.

Journal of Hazardous Materials, 428, p.128214_1 - 128214_10, 2022/04

https://doi.org/10.1016/j.jhazmat.2022.128214

Characterization of deformation by cold rolling in ferritic steel containing Cu particles using neutron transmission analysis

Oba, Yojiro; Morooka, Satoshi; Oishi, Kazuki*; Suzuki, Junichi*; Tsuchiyama, Toshihiro*

ISIJ International, 62(1), p.173 - 178, 2022/01

https://doi.org/10.2355/isijinternational.ISIJINT-2021-144