Present status of the JAEA-AMS-TONO (2022FY)

Fujita, Natsuko; Miyake, Masayasu; Matsubara, Akihiro*; Ishii, Masahiro*; Watanabe, Takahiro; Jinno, Satoshi; Nishio, Tomohiro*; Ogawa, Yumi; Kimura, Kenji; Shimada, Akiomi; et al.

Dai-35-Kai Tandemu Kasokuki Oyobi Sono Shuhen Gijutsu No Kenkyukai Hokokushu, p.17 - 19, 2024/03

The JAEA-AMS-TONO facility at the Tono Geoscience Center, JAEA has three accelerator mass spectrometers. We report the present status of the JAEA-AMS-TONO.

Status report of JAEA-AMS-TONO; Research and technical development in the last four years

Kokubu, Yoko; Fujita, Natsuko; Watanabe, Takahiro; Matsubara, Akihiro; Ishizaka, Chika; Miyake, Masayasu*; Nishio, Tomohiro*; Kato, Motohisa*; Ogawa, Yumi*; Ishii, Masahiro*; et al.

Nuclear Instruments and Methods in Physics Research B, 539, p.68 - 72, 2023/06

https://doi.org/10.1016/j.nimb.2023.03.005

The JAEA-AMS-TONO facility at the Tono Geoscience Center, JAEA has an accelerator mass spectrometer (JAEA-AMS-TONO-5MV). The spectrometer enabled us to use a multi-nuclide AMS of carbon-14 (C), beryllium-10, aluminium-26 and iodine-129, and we have recently been proceeding test measurement of chlorine-36. In response to an increase of samples, we installed a state-of-the-art multi-nuclide AMS with a 300 kV Tandetron accelerator in 2020. Recently, we are driving the development of techniques of isobar separation in AMS and of sample preparation. Ion channeling is applied to remove isobaric interference and we are building a prototype AMS based on this technique for downsizing of AMS. The small sample graphitization for C has been attempted using an automated graphitization equipment equipped with an elemental analyzer.

Recent improvements of the Particle and Heavy Ion Transport code System; PHITS version 3.33

Sato, Tatsuhiko; Iwamoto, Yosuke; Hashimoto, Shintaro; Ogawa, Tatsuhiko; Furuta, Takuya; Abe, Shinichiro; Kai, Takeshi; Matsuya, Yusuke; Matsuda, Norihiro; Hirata, Yuho; et al.

Journal of Nuclear Science and Technology, 9 Pages, 2023/00

https://doi.org/10.1080/00223131.2023.2275736

The Particle and Heavy Ion Transport code System (PHITS) is a general-purpose Monte Carlo radiation transport code that can simulate the behavior of most particle species with energies up to 1 TeV (per nucleon for ions). Its new version, PHITS3.31, was recently developed and released to the public. In the new version, the compatibility with high-energy nuclear data libraries and the algorithm of the track-structure modes have been improved. In this paper, we summarize the upgraded features of PHITS3.31 with respect to the physics models, utility functions, and application software introduced since the release of PHITS3.02 in 2017.

Theoretical and experimental estimation of the relative optically stimulated luminescence efficiency of an optical-fiber-based BaFBr:Eu detector for swift ions

Hirata, Yuho; Sato, Tatsuhiko; Watanabe, Kenichi*; Ogawa, Tatsuhiko; Parisi, A.*; Uritani, Akira*

Journal of Nuclear Science and Technology, 59(7), p.915 - 924, 2022/07

https://doi.org/10.1080/00223131.2021.2017372

The reliability of dose assessment with radiation detectors is an important feature in various fields, such as radiotherapy, radiation protection, and high-energy physics. However, many detectors irradiated by high linear energy transfer (LET) radiations exhibit decreased efficiency called the quenching effect. This quenching effect depends not only on the particle LET but strongly on the ion species and its microscopic pattern of energy deposition. Recently, a computational method for estimating the relative efficiency of luminescence detectors was proposed following analysis of microdosimetric specific energy distributions simulated using the particle and heavy ion transport code system (PHITS). This study applied the model to estimate the relative optically stimulated luminescence (OSL) efficiency of BaFBr:Eu detectors. Additionally, we measured the luminescence intensity of BaFBr:Eu detectors exposed to He, C and Ne ions to verify the calculated data. The model reproduced the experimental data in the cases of adopting a microdosimetric target diameter of approximately 30-50 nm. The calculated relative efficiency exhibit ion-species dependence in addition to LET. This result shows that the microdosimetric calculation from specific energy is a successful method for accurately understanding the results of OSL measurements with BaFBr:Eu detectors irradiated by various particles.

Separation/removal of steel surface coating film by laser cleaning

Yamane, Ikumi; Takahashi, Nobuo; Sawayama, Kengo; Nishiwaki, Hiroki; Matsumoto, Takashi; Ogawa, Jumpei; Nomura, Mitsuo; Arima, Tatsumi*

JAEA-Technology 2021-038, 18 Pages, 2022/02

JAEA-Technology-2021-038.pdf:1.61MB

We have dismantled uranium enrichment facilities in Ningyo-toge Environmental Engineering Center since their operation finished in 2001, and the total amount of metallic wastes is estimated to be about 130 thousand tons. Eighty percent of them can be disposed as nonradioactive waste (NR), but there are some steel parts possibly uranium-contaminated. We need removing painted surface of such steels and radiologically surveying to dispose them as NRs. Though painted surfaces have been conventionally removed through hand working with grinders, this manual work requires installation of green house, protective clothing, and full-face mask, in order to prevent dispersion and inhalation of airborne dusts. We desire further developments of surface cleaning techniques to reduce time, cost, workload, and secondary waste generation caused by excessive grinding. Therefore, in this study, we focused on the laser cleaning technology used for the separation and removal of paint films at construction sites. In order to improve the coating separation and removal technology for NR objects, we evaluated the coating separation and removal performance of NR steel surface by laser cleaning system, observed the coating scattering behavior by high-speed camera and investigated the coating recovery method, evaluated the laser separation and removal performance of steel surface powder, and thermodynamically evaluated the uranium compounds on steel surface. We additionally evaluated the feasibility of laser cleaning techniques in our works basing on these results, and discussed future work plans for further developments of laser cleaning techniques.

Measurement and evaluation of hydrogen production from mixtures of seawater and zeolite in decontamination of radioactive water

Kumagai, Yuta; Nagaishi, Ryuji; Kimura, Atsushi*; Taguchi, Mitsumasa*; Nishihara, Kenji; Yamagishi, Isao; Ogawa, Toru

Insights Concerning the Fukushima Daiichi Nuclear Accident, Vol.4; Endeavors by Scientists, p.37 - 45, 2021/10

Zeolite adsorbents are to be used for decontamination of radioactive water in Fukushima Dai-ichi Nuclear Power Station. Evaluation of hydrogen production by water radiolysis during decontamination is important for safe operation. Thus hydrogen production from the mixture of zeolite adsorbents and seawater was studied because seawater was urgently used as a coolant for the fuels. The hydrogen yield from the mixture decreased at a high weight fraction of zeolites. However, the measured yield was higher than the yield expected from the direct radiolysis of seawater in the mixture, which would decrease proportional to the weight fraction of seawater. The result suggests that the radiation energy deposited to zeolites was involved in the hydrogen formation. From the results, the hydrogen production rate was evaluated to be 3.6 mL/h per ton of radioactive water before decontamination. After the process, it was evaluated to be 1.5 L/h per ton of waste adsorbents due to the high dose rate.

Manufacture of substitutive assemblies for MONJU reactor decommissioning

Sakakibara, Hiroshi; Aoki, Nobuhiro; Muto, Masahiro; Otabe, Jun; Takahashi, Kenji*; Fujita, Naoyuki*; Hiyama, Kazuhiko*; Suzuki, Hirokazu*; Kamogawa, Toshiyuki*; Yokosuka, Toru*; et al.

JAEA-Technology 2020-020, 73 Pages, 2021/03

JAEA-Technology-2020-020.pdf:8.26MB

The decommissioning is currently in progress at the prototype fast breeder reactor Monju. Fuel assemblies will be taken out of its core for the first step of the great task. Fuel assemblies stand on their own spike plugged into a socket on the core support plate and support with adjacent assemblies through their housing pads each other, resulting in steady core structure. For this reason, some substitutive assemblies are necessary for the purpose of discharging the fuel assemblies of the core. Monju side commissioned, therefore, Plutonium Fuel Development Center to manufacture the substitutive assemblies and the Center accepted it. This report gives descriptions of design, manufacture, and shipment in regard to the substitutive assemblies.

Thermally altered subsurface material of asteroid (162173) Ryugu

Kitazato, Kohei*; Milliken, R. E.*; Iwata, Takahiro*; Abe, Masanao*; Otake, Makiko*; Matsuura, Shuji*; Takagi, Yasuhiko*; Nakamura, Tomoki*; Hiroi, Takahiro*; Matsuoka, Moe*; et al.

Nature Astronomy (Internet), 5(3), p.246 - 250, 2021/03

https://doi.org/10.1038/s41550-020-01271-2

Here we report observations of Ryugu's subsurface material by the Near-Infrared Spectrometer (NIRS3) on the Hayabusa2 spacecraft. Reflectance spectra of excavated material exhibit a hydroxyl (OH) absorption feature that is slightly stronger and peak-shifted compared with that observed for the surface, indicating that space weathering and/or radiative heating have caused subtle spectral changes in the uppermost surface. However, the strength and shape of the OH feature still suggests that the subsurface material experienced heating above 300 C, similar to the surface. In contrast, thermophysical modeling indicates that radiative heating does not increase the temperature above 200 C at the estimated excavation depth of 1 m, even if the semimajor axis is reduced to 0.344 au. This supports the hypothesis that primary thermal alteration occurred due to radiogenic and/or impact heating on Ryugu's parent body.

New design and fabrication technology applied in mercury target vessel #8 of J-PARC

Wakui, Takashi; Wakai, Eiichi; Kogawa, Hiroyuki; Naoe, Takashi; Hanano, Kohei; Haga, Katsuhiro; Takada, Hiroshi; Shimada, Tsubasa*; Kanomata, Kenichi*

JPS Conference Proceedings (Internet), 28, p.081002_1 - 081002_6, 2020/02

https://doi.org/10.7566/JPSCP.28.081002

A mercury target vessel of J-PRAC is designed with a triple-walled structure consisting of the mercury vessel and a double-walled water shroud with internal and external vessels. During the beam operation at 500 kW in 2015, small water leakages from a water shroud of the mercury target vessel occurred twice. Design, fabrication and inspection processes were improved based on the lessons learned from the target failures. The total length of welding lines at the front of the mercury target vessel decreases drastically to approximately 55% by adopting monolithic structure cut out from a block of stainless steel by the wire-electrical discharge machining. Thorough testing of welds by radiographic testing and ultrasonic testing was conducted. The fabrication of the mercury target vessel #8 was finished on September 2017 and the beam operation using it started. Stable beam operation at 500 kW has been achieved and it could experience the maximum beam power of 1 MW during a beam test.

Effects of the nuclear structure of fission fragments on the high-energy prompt fission -ray spectrum in U()

Makii, Hiroyuki; Nishio, Katsuhisa; Hirose, Kentaro; Orlandi, R.; Lguillon, R.; Ogawa, Tatsuhiko; Soldner, T.*; Kster, U.*; Pollitt, A.*; Hambsch, F.-J.*; et al.

Physical Review C, 100(4), p.044610_1 - 044610_7, 2019/10

https://doi.org/10.1103/PhysRevC.100.044610