Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Abe, Shinichiro; Hashimoto, Masanori*; Liao, W.*; Kato, Takashi*; Asai, Hiroaki*; Shimbo, Kenichi*; Matsuyama, Hideya*; Sato, Tatsuhiko; Kobayashi, Kazutoshi*; Watanabe, Yukinobu*
IEEE Transactions on Nuclear Science, 70(8, Part 1), p.1652 - 1657, 2023/08
Times Cited Count：0 Percentile：0.01(Engineering, Electrical & Electronic)Single event upsets (SEUs) caused by neutrons is a reliability problem for microelectronic devices in the terrestrial environment. Acceleration tests using white neutron beam provide realistic soft error rates (SERs), but only a few facilities can provide white neutron beam in the world. If single-source irradiation applicable to diverse neutron source can be utilized for the evaluation of the SER in the terrestrial environment, it contributes to solve the shortage of beam time. In this study, we investigated the feasibility of the SER estimation in the terrestrial environment by any one of these measured data with the SEU cross sections obtained by PHITS simulation. It was found that the SERs estimated by our proposed method are within a factor of 2.7 of that estimated by the Weibull function. We also investigated the effect of simplification which reduce the computational cost in simulation to the SER estimation.
Sanada, Yukihisa; Tokiyoshi, Masanori*; Nishiyama, Kyohei*; Sato, Rina; Yoshimura, Kazuya; Funaki, Hironori; Abe, Tomohisa; Ishida, Mutsushi*; Nagamine, Haruo*; Fujisaka, Motoyuki*
Nihon Genshiryoku Gakkai Wabun Rombunshi (Internet), 22(2), p.87 - 96, 2023/04
Since the accident at the Fukushima Daiichi Nuclear Power Plant, many decontamination works have been carried out, but it is difficult to say that much data on workers' exposure has necessarily been analyzed in detail. In this paper, based on the GPS location information carried by the workers together with their personal dosimeters, the air dose rate in the work area and the characteristics of each type of work were analyzed. The results showed that more than 50% of the measured actual doses were more than twice the median planned dose calculated from the air dose rate and actual working hours. Furthermore, as a result of the analysis by work type, it was found that the exposure doses of demolition workers tended to be high, and that this was due to the fact that most of the work was carried out before the work was carried out to reduce the dose at the work site. In addition, when the conversion from air dose to effective dose was taken into account, there were many cases of underestimation where the planned values were lower than the measured values, and it is considered important for management to set appropriate working factor.
Nara, Yoshitaka*; Kato, Masaji*; Sato, Tsutomu*; Kono, Masanori*; Sato, Toshinori
Journal of MMIJ, 138(4), p.44 - 50, 2022/04
It is important to understand the long-term migration of radionuclides when considering rock engineering projects such as the geological disposal of radioactive waste. The network of fractures and pores in a rock mass plays a major role in fluid migration as it provides a pathway for fluid flow. The geometry of a network can change due to fracture sealing by some fine-grained materials over long-term periods. In the present study, we use a macro-fractured granite sample to investigate the change of permeability that occurs under the flow of water that includes two different amounts of clay. Findings showed that clay accumulated in a fracture and that the permeability (hydraulic conductivity) of the granite sample decreased over time, which was greater in for the higher clay content. We concluded that the accumulation of clay minerals in the fracture decreased the permeability of the rock. Furthermore, we consider that the filling and closure of fractures in rock is possible under the flow of groundwater that includes clay minerals.
-Orbital component in the Borromean nucleus 
BYang, Z. H.*; Kubota, Yuki*; Corsi, A.*; Yoshida, Kazuki; Sun, X.-X.*; Li, J. G.*; Kimura, Masaaki*; Michel, N.*; Ogata, Kazuyuki*; Yuan, C. X.*; et al.
Physical Review Letters, 126(8), p.082501_1 - 082501_8, 2021/02
Times Cited Count：43 Percentile：96.7(Physics, Multidisciplinary)A quasifree (
,
) experiment was performed to study the structure of the Borromean nucleus B, which had long been considered to have a neutron halo. By analyzing the momentum distributions and exclusive cross sections, we obtained the spectroscopic factors for 
and 
orbitals, and a surprisingly small percentage of 9(2)% was determined for . Our finding of such a small component and the halo features reported in prior experiments can be explained by the deformed relativistic Hartree-Bogoliubov theory in continuum, revealing a definite but not dominant neutron halo in B. The present work gives the smallest - or -orbital component among known nuclei exhibiting halo features and implies that the dominant occupation of or orbitals is not a prerequisite for the occurrence of a neutron halo.
Abe, Shinichiro; Sato, Tatsuhiko; Kuroda, Junya*; Manabe, Seiya*; Watanabe, Yukinobu*; Liao, W.*; Ito, Kojiro*; Hashimoto, Masanori*; Harada, Masahide; Oikawa, Kenichi; et al.
Proceedings of IEEE International Reliability Physics Symposium (IRPS 2020) (Internet), 6 Pages, 2020/04
Times Cited Count：2 Percentile：64.23(Engineering, Electrical & Electronic)Single event upsets (SEUs) caused by neutrons have been recognized as a serious reliability problem for microelectronic devices on the ground level. In our previous work, it was found that hydride placed in front of the memory chip has considerably impact on SEU cross sections because H ions generated via elastic scattering of neutrons with hydrogen atoms are only emitted in a forward direction. In this study, the effect of components neighboring transistors on neutron-induced SEUs was investigated for 65-nm bulk SRAMs by using PHITS. It was found that the shape of the SEU cross section around few MeV comes from the thickness and the position of components placed in front of transistors when that components do not contains hydrogen atoms. By considering components adjoin memory cells in the test board used in the simulation, measured data at J-PARC BL10 were reproduced well. In addition, it was found that the effect of components neighboring transistors on neutron-induced SERs does not negligible in terrestrial environment.
Nara, Yoshitaka*; Kato, Masaji*; Sato, Tsutomu*; Kono, Masanori*; Sato, Toshinori
Proceedings of 5th ISRM Young Scholars' Symposium on Rock Mechanics and International Symposium on Rock Engineering for Innovative Future (YSRM 2019 and REIF 2019) (USB Flash Drive), 6 Pages, 2019/12
It is important to understand the long-term migration of radionuclides considering carious rock engineering projects such as the geological disposal of radioactive wastes. The network of fractures and pores in a rock mass can play important roles as the pathway of the fluid flow of rock. Usually groundwater contains fine-grained minerals such as clays. It is probable that the accumulation of the fine-grained minerals occurs in a fracture if the groundwater flows in a fracture in a rock. In this study, we have conducted the permeability measurement using water including clays. Specifically, we used a macro-fractured granite as a rock sample, and investigated the change of the permeability under the flow of the water including clays. It was shown that the hydraulic conductivity decreased with elapsed time.
Abe, Shinichiro; Liao, W.*; Manabe, Seiya*; Sato, Tatsuhiko; Hashimoto, Masanori*; Watanabe, Yukinobu*
IEEE Transactions on Nuclear Science, 66(7, Part 2 ), p.1374 - 1380, 2019/07
Times Cited Count：7 Percentile：61.94(Engineering, Electrical & Electronic)Single event upsets (SEUs) caused by secondary cosmic-ray neutrons have recognized as a serious reliability problem for microelectronic devices. Acceleration tests at neutron facilities are convenient to validate soft error rates (SERs) quickly, but some corrections caused from measurement conditions are required to derive realistic SERs at actual environment or to compare other measured data. In this study, the effect of irradiation side on neutron-induced SEU cross sections was investigated by performing neutron transport simulation using PHITS. SERs for 65-nm bulk CMOS SRAMs are estimated using the sensitive volume model. It was found from simulation that SERs for the sealant side irradiation are 30-50% larger than those for the board side irradiation. This difference comes from the difference of production yield and angular distribution of secondary H and He ions, which are the main cause of SEUs. Thus the direction of neutron irradiation should be reported when the result of acceleration tests are published. This result also indicates that SERs can be reduced by equipping device with sealant side facing downward.
Sato, Yuji*; Tsukamoto, Masahiro*; Shobu, Takahisa; Funada, Yoshinori*; Yamashita, Yorihiro*; Hara, Takahiro*; Sengoku, Masanori*; Sakon, Yu*; Okubo, Tomomasa*; Yoshida, Minoru*; et al.
Applied Surface Science, 480, p.861 - 867, 2019/06
Times Cited Count：30 Percentile：82.18(Chemistry, Physical)Kato, Masaji*; Nara, Yoshitaka*; Okazaki, Yuki*; Kono, Masanori*; Sato, Toshinori; Sato, Tsutomu*; Takahashi, Manabu*
Materials Transactions, 59(9), p.1427 - 1432, 2018/09
Times Cited Count：6 Percentile：32.61(Materials Science, Multidisciplinary)To ensure the safe geological disposal of radioactive waste, it is important to determine the permeability (hydraulic conductivity) of clays. The transient pulse method is suitable for low-permeability materials because it requires a relatively short time to determine their permeability. Upstream pore pressure typically increases in the measurement conducted via the transient pulse method. However, this procedure cannot be used to determine the permeability of clays due to the increase in pore pressure. Therefore, the transient pulse method has never been applied to determine clay permeability. In this study, we applied the transient pulse method to a clay sample to determine its permeability while decreasing the downstream pore pressure.
Manabe, Seiya*; Watanabe, Yukinobu*; Liao, W.*; Hashimoto, Masanori*; Nakano, Keita*; Sato, Hikaru*; Kin, Tadahiro*; Abe, Shinichiro; Hamada, Koji*; Tampo, Motonobu*; et al.
IEEE Transactions on Nuclear Science, 65(8), p.1742 - 1749, 2018/08
Times Cited Count：8 Percentile：62.99(Engineering, Electrical & Electronic)Recently, the malfunction of microelectronics caused by secondary cosmic-ray muon is concerned as semiconductor devices become sensitive to radiation. In this study, we have performed muon irradiation testing for 65-nm ultra-thin body and thin buried oxide (UTBB-SOI) SRAMs in the Japan Proton Accelerator Research Complex (J-PARC), in order to investigate dependencies of single event upset (SEU) cross section on incident muon momentum and supply voltage. It was found that the SEU cross section by negative muon are approximately two to four times larger than those by positive muon in the momentum range from 35 MeV/c to 39 MeV/c. The supply voltage dependence of muon-induced SEU cross section was measured with the momentum of 38 MeV/c. SEU cross sections decrease with increasing supply voltage, but the decreasing of SEU cross section by negative muon is gentler than that by positive muon. Experimental data of positive and negative muon irradiation with the momentum of 38 MeV/c were analyzed by PHITS. It was clarified that the negative muon capture causes the difference between the SEU cross section by negative muon and that by positive muon.
Liao, W.*; Hashimoto, Masanori*; Manabe, Seiya*; Watanabe, Yukinobu*; Abe, Shinichiro; Nakano, Keita*; Sato, Hikaru*; Kin, Tadahiro*; Hamada, Koji*; Tampo, Motonobu*; et al.
IEEE Transactions on Nuclear Science, 65(8), p.1734 - 1741, 2018/08
Times Cited Count：14 Percentile：81.7(Engineering, Electrical & Electronic)Soft error induced by secondary cosmic-ray muon is concerned since susceptibility of semiconductor device to soft error increases with the scaling of technology. In this study, we have performed irradiation tests of muons on 65-nm bulk CMOS SRAM in the Japan Proton Accelerator Research Complex (J-PARC) and measured soft error rate (SER) to investigate mechanism of muon-induced soft errors. It was found that SER by negative muon increases above 0.5 V supply voltage, although SER by positive muon increases monotonically as the supply voltage lowers. SER by negative muon also increases with forward body bias. In addition, negative muon causes large multiple cell upset (MCU) of more than 20 bits and the ratio of MCU events to all the events is 66% at 1.2V supply voltage. These tendencies indicate that parasitic bipolar action (PBA) is highly possible to contribute to SER by negative muon. Experimental data are analyzed by PHITS. It was found that negative muon can deposit larger charge than positive muon, and such events that can deposit large charge may trigger PBA.
Nara, Yoshitaka*; Kuwatani, Ryuta*; Kono, Masanori*; Sato, Toshinori; Kashiwaya, Koki*
Zairyo, 67(7), p.730 - 737, 2018/07
Information of confining ability of rock is important for the geological disposal of radioactive wastes. To maintain or improve the confining ability of rocks, it is important to seal pores and cracks. In this study, we investigated the precipitation of minerals on the rock surface. As rock samples, we used Berea sandstone and Toki granite in this study. It was shown that precipitation occurred on the surface of rock specimens kept in calcium hydroxide solution for 1 month if the concentration was high. Specifically, if the concentration of calcium hydroxide solution was higher than 300 mg/l, the precipitation occurred obviously. After keeping rock specimens in calcium hydroxide solution, the weight of the rock samples increased and the concentration of calcium ion decreased by the precipitation. It is considered that the calcium ion in water was used for the precipitation on rock surfaces. Since the precipitation has been recognized for rock surfaces, it is possible to seal pores and cracks in rocks. Therefore, it is also possible to keep or decrease the permeability of rocks by the precipitation of calcium compounds.
Okano, Masanori; Akiyama, Kazuki; Taguchi, Katsuya; Nagasato, Yoshihiko; Omori, Eiichi
Dekomisshoningu Giho, (57), p.53 - 64, 2018/03
The construction of Tokai Reprocessing Plant (TRP) was initiated in June 1971, and its hot test using spent fuel started in September 1977. Thereafter TRP had been operated to reprocess 1,140 tons of spent fuel for approximately 30 years until May 2007, according to the reprocessing contract with domestic electric power companies. JAEA announced a policy of TRP in report of JAEA reform plan published in September 2014. The policy shows that TRP will shift to a decommissioning stage by economic reasons. Based on the policy, application of approval for TRP decommissioning plan was submitted to Nuclear Regulation Authority (NRA) in June 2017. This plan provides basic guidelines such as procedures for decommissioning and specific activities for risk reduction, and implementation divisions of decommissioning, management of spent fuels and radioactive wastes, decommissioning budget, and decommissioning schedule. The process of TRP decommissioning is planned to continue for approximately 70 years until the release of controlled areas of approximately 30 facilities.
Nara, Yoshitaka*; Kato, Masaji*; Niri, Ryuhei*; Kono, Masanori*; Sato, Toshinori; Fukuda, Daisuke*; Sato, Tsutomu*; Takahashi, Manabu*
Pure and Applied Geophysics, 175(3), p.917 - 927, 2018/03
Times Cited Count：14 Percentile：58.67(Geochemistry & Geophysics)Information on the permeability of rock is essential for various geoengineering projects. It is especially important to investigate how fractures and pores influence the physical and transport properties of rock. Infiltration of groundwater through the damage zone fills fractures in granite with fine-grained minerals. However, the permeability of rock possessing a fracture naturally filled with fine-grained mineral grains has yet to be investigated. In this study, the permeabilities of granite samples, including a macro-fracture filled with clay and a mineral vein, are investigated. The permeability of granite with a fine-grained mineral vein agrees well with that of the intact sample, whereas the permeability of granite possessing a macro-fracture filled with clay is lower than that of the macro-fractured sample. The decrease in the permeability is due to the filling of fine-grained minerals and clay in the macro-fracture. It is concluded that the permeability of granite increases due to the existence of the fractures, but decreases upon filling them with fine-grained minerals.
Kato, Masaji*; Nara, Yoshitaka*; Okazaki, Yuki*; Kono, Masanori*; Sato, Toshinori; Sato, Tsutomu*; Takahashi, Manabu*
Zairyo, 67(3), p.318 - 323, 2018/03
To ensure the safe geological disposal of radioactive wastes, it is important to determine the permeability of clays. The transient pulse test is suitable to apply to the low permeability materials, because it takes relatively short term to determine the permeability. Usually we increase the upstream pore pressure in the measurement with the transient pulse test. However, it is impossible to determine the permeability of clay in this procedure because of the increase of pore pressure. Therefore, the transient pulse test has never been applied to the determination of permeability of clays. In this study, we tried to apply the transient pulse test to a clay obtained in Mizunami Underground Research Laboratory to determine the permeability with decreasing the downstream pore pressure. It was clarified that the transient pulse test with decreasing downstream pore pressure is appropriate from the measurements of granite and sandstone. It was shown that the permeability of a clay was determined by the transient pulse test with decreasing the downstream pore pressure, which agreed with the permeability determined from the falling head test. The measurement time of the transient pulse test is much shorter than that of the falling head test. It is concluded that the transient pulse test is appropriate for the determination of the permeability of clays.
Homma, Toshimitsu; Takahara, Shogo; Iijima, Masashi; Sato, Sohei; Kimura, Masanori; Shimada, Kazumasa
JAEA-Review 2016-013, 162 Pages, 2016/07
JAEA-Review-2016-013.pdf:16.95MB
This is a Japanese translation of "Actions to Protect the Public in an Emergency due to Severe Conditions at a Light Water Reactor", which is published by the International Atomic Energy Agency in May 2013. The original IAEA Publication is available on the IAEA Website (https://www-pub.iaea.org/MTCD/Publications/PDF/EPR-NPP_PPA_web.pdf).
Kato, Masaji*; Nara, Yoshitaka*; Fukuda, Daisuke*; Kono, Masanori*; Sato, Toshinori; Sato, Tsutomu*; Takahashi, Manabu*
Zairyo, 65(7), p.489 - 495, 2016/07
Rock masses serve a vital function as natural barriers for geological disposal of radioactive waste; therefore, information on rock permeability is essential. Highly accurate measurement of permeability requires understanding of how temperature changes in the surrounding environment influence measurement results. We performed permeability measurement under conditions with dramatic changes of temperature in the surrounding environment to investigate the influence of such changes on the experimental results. Measurement of permeability with no temperature change was also conducted as reference. All measurements were conducted using the transient pulse method, and the sample material used was Toki granite obtained from Gifu Prefecture in central Japan. We found that temperature changes in the surrounding environment remarkably affected the pressure in reservoirs upstream and downstream, the pressure difference between them, and the confining pressure; all increased when temperature increased for our experimental system. Notably, pressure difference was affected immediately. This difference directly relates to estimation of permeability.
Watanabe, Hitoshi; Nakano, Masanao; Fujita, Hiroki; Takeyasu, Masanori; Mizutani, Tomoko; Isozaki, Tokuju*; Nagaoka, Mika; Hokama, Tomonori; Yokoyama, Hiroya; Nishimura, Tomohiro; et al.
JAEA-Review 2015-034, 175 Pages, 2016/03
JAEA-Review-2015-034.pdf:8.13MB
Environmental radiation monitoring around the Tokai Reprocessing Plant has been performed by the Nuclear Fuel Cycle Engineering Laboratories, based on "Safety Regulations for the Reprocessing Plant of Japan Atomic Energy Agency, Chapter IV - Environmental Monitoring". This annual report presents the results of the environmental monitoring and the dose estimation to the hypothetical inhabitant due to the radioactivity discharged from the plant to the atmosphere and the sea during April 2014 to March 2015. In this report, some data include the influence of the accidental release from the Fukushima Daiichi Nuclear Power Station of Tokyo Electric Power Co. in March 2011.
Ishizawa, Akihiro*; Idomura, Yasuhiro; Imadera, Kenji*; Kasuya, Naohiro*; Kanno, Ryutaro*; Satake, Shinsuke*; Tatsuno, Tomoya*; Nakata, Motoki*; Nunami, Masanori*; Maeyama, Shinya*; et al.
Purazuma, Kaku Yugo Gakkai-Shi, 92(3), p.157 - 210, 2016/03
The high-performance computer system Helios which is located at The Computational Simulation Centre (CSC) in The International Fusion Energy Research Centre (IFERC) started its operation in January 2012 under the Broader Approach (BA) agreement between Japan and the EU. The Helios system has been used for magnetised fusion related simulation studies in the EU and Japan and has kept high average usage rate. As a result, the Helios system has contributed to many research products in a wide range of research areas from core plasma physics to reactor material and reactor engineering. This project review gives a short catalogue of domestic simulation research projects. First, we outline the IFERC-CSC project. After that, shown are objectives of the research projects, numerical schemes used in simulation codes, obtained results and necessary computations in future.
Shimomura, Kenta; Kato, Shoichi; Wakai, Takashi; Ando, Masanori; Hirose, Yuichi*; Sato, Kenichiro*
Proceedings of 23rd International Conference on Nuclear Engineering (ICONE-23) (DVD-ROM), 9 Pages, 2015/05
This paper describes experimental and analytical works to confirm that the design standard for SFR components sufficiently covers possible failure mechanisms. Creep-fatigue damage evaluation method in JSME design standard for SFR components has been constructed based on experiments and/or numerical analyses of conventional austenitic stainless steels, such as 304SS. Since the material characteristics of Mod.9Cr-1Mo steel are substantially different from those of austenitic stainless steels, it is required to verify the applicability of the design standards to the SFR components made of Mod.9Cr-1Mo steel. A series of uni-axial creep-fatigue tests were conducted using double-ended notch bar specimens made of Mod.9Cr-1Mo steel under displacement controlled condition with 30 minute holding. The curvature radii of the specimens were 1.6mm, 11.2mm and 40.0mm. The specimen having 1.6mm notch and 11.2mm notch failed from outer surface but the specimen having 40.0mm notch showed obvious internal crack nucleation. In addition, though total duration time of the creep-fatigue test was only 2,000 hours, a lot of creep voids and inter granular crack growth were observed. To clarify the cause of such peculiar failure, some additional experiments were performed, as well as some numerical analyses. We could point out that such a peculiar failure aspect might result from corresponding stress distribution in the cross section. As a result of a series of investigations, possible causes of such peculiar failure could be narrowed down. A future investigation plan was proposed to clarify the most significant cause.
