Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Kondo, Yasuhiro; Hirano, Koichiro; Ito, Takashi; Kikuzawa, Nobuhiro; Kitamura, Ryo; Morishita, Takatoshi; Oguri, Hidetomo; Okoshi, Kiyonori; Shinozaki, Shinichi; Shinto, Katsuhiro; et al.
Journal of Physics; Conference Series, 1350, p.012077_1 - 012077_7, 2019/12
Times Cited Count：1 Percentile：51.97(Physics, Particles & Fields)We have upgraded a 3-MeV linac at J-PARC. The ion source is same as the J-PARC linac's, and the old 30-mA RFQ is replaced by a spare 50-mA RFQ, therefore, the beam energy is 3 MeV and the nominal beam current is 50 mA. The main purpose of this system is to test the spare RFQ, but also used for testing of various components required in order to keep the stable operation of the J-PARC accelerator. The accelerator has been already commissioned, and measurement programs have been started. In this paper, present status of this 3-MeV linac is presented.
Fuwa, Yasuhiro; Shinozaki, Shinichi; Chishiro, Etsuji; Hirane, Tatsuya; Fang, Z.*; Fukui, Yuji*; Futatsukawa, Kenta*; Mizobata, Satoshi*; Iwama, Yuhei*; Sato, Yoshikatsu*; et al.
Proceedings of 16th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.611 - 613, 2019/10
In the J-PARC linac, a proton accelerator is operated using 45 units of 324 MHz and 972 MHz klystrons. In the future stabilization and advancement of the accelerator, it is important to acquire the klystron output characteristics near the maximum output accurately. In order to understand this characteristics, measurement of the characteristics of the replaced klystron for some reason such as discharge, as well as the new klystron. However, such measurements have not been performed because of the risk of damage including peripheral equipment due to discharge and the temporal interference with the operation of the accelerator. Therefore, we set up a klystron test stand in the linac building and measured the high-voltage characteristics and input/output characteristics of the klystron under various operating parameters. By using this measurement result, the characteristics of klystron can be obtained before installation, and it becomes possible to determine the optimum operation parameters and make effective plan of klystron replacements. In addition, basic data for predicting the degradation tendency of klystron was acquired by comparing the characteristics of the used and used klystron.
Kondo, Yasuhiro; Asano, Hiroyuki*; Chishiro, Etsuji; Hirano, Koichiro; Ishiyama, Tatsuya; Ito, Takashi; Kawane, Yusuke; Kikuzawa, Nobuhiro; Meigo, Shinichiro; Miura, Akihiko; et al.
Proceedings of 28th International Linear Accelerator Conference (LINAC 2016) (Internet), p.298 - 300, 2017/05
We have constructed a linac for development of various accelerator components at J-PARC. The ion source is same as the J-PARC linac's, and the RFQ is a used one in the J-PARC linac. The beam energy is 3 MeV and nominal beam current is 30 mA. The accelerator has been already commissioned, and the first development program, laser-charge-exchange experiment for the transmutation experimental facility, has been started. In this paper, present status of this 3-MeV linac is presented.
Hirano, Koichiro; Asano, Hiroyuki; Ishiyama, Tatsuya; Ito, Takashi; Okoshi, Kiyonori; Oguri, Hidetomo; Kondo, Yasuhiro; Kawane, Yusuke; Kikuzawa, Nobuhiro; Sato, Yoshikatsu; et al.
Proceedings of 13th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.310 - 313, 2016/11
We have used a beam scraper with the incident angle of 65deg to reduce the beam power deposition density in the MEBT between a 324 MHz RFQ and a 50-MeV DTL of the J-PARC linac. The 65
scraper was irradiated by the H
beam up to particle number of 1.47E22. We observed a lot of surface projections with several hundred micrometers high in the beam irradiation damage on the scraper by using the laser microscope. In order to study the limits of scrapers, we constructed a new 3 MeV linac at J-PARC. We will conduct the scraper irradiation test at the end of this year.
Oguri, Hidetomo; Hasegawa, Kazuo; Ito, Takashi; Chishiro, Etsuji; Hirano, Koichiro; Morishita, Takatoshi; Shinozaki, Shinichi; Ao, Hiroyuki; Okoshi, Kiyonori; Kondo, Yasuhiro; et al.
Proceedings of 11th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.389 - 393, 2014/10
no abstracts in English
Monji, Hideaki*; Shinozaki, Tatsuya*; Kamide, Hideki; Sakai, Takaaki
Journal of Engineering for Gas Turbines and Power, 132(1), p.012901_1 - 012901_8, 2010/01
Times Cited Count：19 Percentile：64.21(Engineering, Mechanical)This paper deals with characteristics of surface vortex in a cylindrical vessel. One of the characteristics is a gas core length which is important to estimate the onset condition of the gas entrainment but influenced easily by the experimental condition. In the experiment using water, the effects of the water temperature, water level and the surface tension on the gas core length were investigated. The onset condition of the gas entrainment is sometimes estimated by using the Burgers vortex model but the real flow in the vessel is different from the model. The velocity fields were measured by PIV and the velocity gradient of the downward flow was discussed. The proper flow conditions for the Burgers vortex model are a high water level and a high flow rate.
Monji, Hideaki*; Shinozaki, Tatsuya*; Kamide, Hideki; Sakai, Takaaki
Proceedings of 16th International Conference on Nuclear Engineering (ICONE-16) (CD-ROM), 9 Pages, 2008/05
This paper deals with characteristics of surface vortex in a cylindrical vessel. One of the characteristics is a gas core length which is important to estimate the onset condition of the gas entrainment but influenced easily by the experimental condition. In the experiment using water, the effects of the water temperature, water level and the surface tension on the gas core length were investigated. The onset condition of the gas entrainment is sometimes estimated by using the Burgers vortex model but the real flow in the vessel is different from the model. The velocity fields were measured by PIV and the velocity gradient of the downward flow was discussed. The proper flow conditions for the Burgers vortex model are a high water level and a high flow rate.
Shinozaki, Tatsuya*; Monji, Hideaki*; Kamide, Hideki
no journal, ,
The aim of this study is to reveal the influences of the working fluid properties, the flow configuration and the flow conditions on the characteristics of the free surface vortex. For investigation on the working fluid effect, temperature of the fluid was varied. Flow configuration was altered by changing the water level and by adding structures to the outlet. Then, we investigated the shape of the detached bubble when the surface active agent is added. We found out that all these parameters have considerable influences on the behavior of the free surface vortex.
screening of target kinases of AtATRSakamoto, Ayako; Nemoto, Keiichiro*; Seki, Motoaki*; Shinozaki, Kazuo*; Sawasaki, Tatsuya*
no journal, ,
