Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Nishikiori, Ryo; Kojima, Atsushi; Hanada, Masaya; Kashiwagi, Mieko; Watanabe, Kazuhiro; Umeda, Naotaka; Tobari, Hiroyuki; Yoshida, Masafumi; Ichikawa, Masahiro; Hiratsuka, Junichi; et al.
Plasma and Fusion Research (Internet), 11, p.2401014_1 - 2401014_4, 2016/03
One of critical issues for high-energy high-current beam acceleration in ITER and JT-60SA is the high voltage holding which is dominated by vacuum discharges. The past results suggest that vacuum discharge occurs beyond the threshold of the dark current. The dark current can be derived from F-N theory where electric field enhancement factor beta is included. Though, beta could only be evaluated from the experiment previously. Therefore, the method to decide beta without experiment is required. This time dark currents were measured at three different areas to compare beta in different electric field. As a result, the effective electric field 
E, where E is average electric field, were found to be almost constant for different areas although the beta is largely different. By applying E, beta can be evaluated analytically, leading to the analytical prediction of the dark current and voltage holding capability without the measurements.
Hiratsuka, Junichi; Hanada, Masaya; Kojima, Atsushi; Umeda, Naotaka; Kashiwagi, Mieko; Miyamoto, Kenji*; Yoshida, Masafumi; Nishikiori, Ryo; Ichikawa, Masahiro; Watanabe, Kazuhiro; et al.
Review of Scientific Instruments, 87(2), p.02B137_1 - 02B137_3, 2016/02
Times Cited Count：4 Percentile：21.76(Instruments & Instrumentation)To understand the physics of the negative ion extraction/acceleration, the heat load density profile on the acceleration grid has been firstly measured in the ITER prototype accelerator where the negative ions are accelerated to 1 MeV with five acceleration stages. In order to clarify the profile, the peripheries around the apertures on the acceleration grid were separated into thermally insulated 34 blocks with thermocouples. The spatial resolution is as low as 3 mm and small enough to measure the tail of the beam profile with a beam diameter of 16 mm. It was found that there were two peaks of heat load density around the aperture. These two peaks were also clarified to be caused by the intercepted negative ions and secondary electrons from detailed investigation by changing the beam optics and gas density profile. This is the first experimental result, which is useful to understand the trajectories of these particles.
Yoshida, Masafumi; Hanada, Masaya; Kojima, Atsushi; Kashiwagi, Mieko; Umeda, Naotaka; Hiratsuka, Junichi; Ichikawa, Masahiro; Watanabe, Kazuhiro; Grisham, L. R.*; Tsumori, Katsuyoshi*; et al.
Review of Scientific Instruments, 87(2), p.02B144_1 - 02B144_4, 2016/02
Times Cited Count：9 Percentile：42.81(Instruments & Instrumentation)Time evolution of spatial profile of negative ion production during an initial conditioning phase has been experimentally investigated in the JT-60 negative ion source. Up to 0.4 g Cs injection, there is no enhancement of the negative ion production and no observation of the Cs emission signal in the source, suggesting the injected Cs is mainly deposited on the water-cooled wall near the nozzle. After 0.4 g Cs injection, enhancement of the negative ion production appeared only at the central segment of the PG. The calculation of the Cs neutral/ion trajectories implied that a part of Cs was ionized near the nozzle and was transported to this area. The expansion of the area of the surface production was saturated after ~2 g Cs injection corresponding to 6000 s discharge time. From the results, it is found that Cs ionization and its transport plays an important role for the negative ion production.
Kojima, Atsushi; Hanada, Masaya; Tobari, Hiroyuki; Nishikiori, Ryo; Hiratsuka, Junichi; Kashiwagi, Mieko; Umeda, Naotaka; Yoshida, Masafumi; Ichikawa, Masahiro; Watanabe, Kazuhiro; et al.
Review of Scientific Instruments, 87(2), p.02B304_1 - 02B304_5, 2016/02
Times Cited Count：11 Percentile：49.05(Instruments & Instrumentation)Optimization techniques of the vacuum insulation design have been developed in order to realize a reliable voltage holding capability of Multi-Aperture Multi-Grid accelerators for giant negative ion sources for nuclear fusion. In this method, the nested multilayer configuration of each acceleration stage in the MAMuG accelerator can be uniquely designed to satisfy the target voltage within given boundary conditions. The evaluation of the voltage holding capabilities of each acceleration stages were based on the past experimental results of the area effect and the multi-aperture effect on the voltage holding capability. Moreover, total voltage holding capability of multi-stage was estimated by taking the multi-stage effect into account, which was experimentally obtained in this time. In this experiment, the multi-stage effect appeared as the superposition of breakdown probabilities in each acceleration stage, which suggested that multi-stage effect can be considered as the voltage holding capability of the single acceleration gap having the total area and aperture. The analysis on the MAMuG accelerator for JT-60SA agreed with the past gap-scan experiments with an accuracy of less than 10% variation.
Hanada, Masaya; Kojima, Atsushi; Tobari, Hiroyuki; Nishikiori, Ryo; Hiratsuka, Junichi; Kashiwagi, Mieko; Umeda, Naotaka; Yoshida, Masafumi; Ichikawa, Masahiro; Watanabe, Kazuhiro; et al.
Review of Scientific Instruments, 87(2), p.02B322_1 - 02B322_4, 2016/02
Times Cited Count：11 Percentile：49.05(Instruments & Instrumentation)In International Thermo-nuclear Experimental Reactor (ITER) and JT-60 Super Advanced (JT-60 SA), the D
ion beams of 1 MeV, 40 A and 0.5 MeV, 22 A are required to produce 3600 s and 100 s for the neutral beam injection, respectively. In order to realize such as powerful D ion beams for long duration time, Japan Atomic Energy Agency (JAEA) has energetically developed cesium (Cs)-seeded negative ion sources (CsNIS) and electro-static multi-aperture and multi-stage accelerators (MAMuG accelerator) which are chosen as the reference design of ITER and JT-60 SA. In the development of the CsNIS, a 100s production of the H ion beam has been demonstrated with a beam current of 15 A by modifying the JT-60 negative ion source. At the higher current, the long pulse production of the negative ions has been tried by the mitigation of the arcing in the plasma inside the ion source. As for the long pulse acceleration of the negative ions in the MAMuG accelerator, the beam steering angle has been controlled to reduce the power loading of the acceleration grids A pulse duration time has been significantly extended from 0.4 s to 60 s at reasonable beam power for ITER requirement. The achieved pulse duration time is limited by the capacity of the power supplies in the test stand. In the range of 
60 s, there are no degradations of beam optics and voltage holding capability in the accelerator. It leads to the further extension of the pulse duration time at higher power density. This paper reports the latest results of development on the negative ion source and accelerator at JAEA.
Kojima, Atsushi; Umeda, Naotaka; Hanada, Masaya; Yoshida, Masafumi; Kashiwagi, Mieko; Tobari, Hiroyuki; Watanabe, Kazuhiro; Akino, Noboru; Komata, Masao; Mogaki, Kazuhiko; et al.
Nuclear Fusion, 55(6), p.063006_1 - 063006_9, 2015/06
Times Cited Count：41 Percentile：89.45(Physics, Fluids & Plasmas)Significant progresses in the extension of pulse durations of powerful negative ion beams have been made to realize the neutral beam injectors for JT-60SA and ITER. In order to overcome common issues of the long pulse production/acceleration of negative ion beams in JT-60SA and ITER, the new technologies have been developed in the JT-60SA ion source and the MeV accelerator in Japan Atomic Energy Agency. As for the long pulse production of high-current negative ions for JT-60SA ion source, the pulse durations have been successfully increased from 30 s at 13 A on JT-60U to 100 s at 15 A by modifying the JT-60SA ion source, which satisfies the required pulse duration of 100 s and 70% of the rated beam current for JT-60SA. This progress was based on the R&D efforts for the temperature control of the plasma grid and uniform negative ion productions with the modified tent-shaped filter field configuration. Moreover, the each parameter of the required beam energy, current and pulse has been achieved individually by these R&D efforts. The developed techniques are useful to design the ITER ion source because the sustainment of the cesium coverage in large extraction area is one of the common issues between JT-60SA and ITER. As for the long pulse acceleration of high power density beams in the MeV accelerator for ITER, the pulse duration of MeV-class negative ion beams has been extended by more than 2 orders of magnitude by modifying the extraction grid with a high cooling capability and a high-transmission of negative ions. A long pulse acceleration of 60 s has been achieved at 70 MW/m
(683 keV, 100 A/m) which has reached to the power density of JT-60SA level of 65 MW/m.
Kojima, Atsushi; Hanada, Masaya; Yoshida, Masafumi; Umeda, Naotaka; Hiratsuka, Junichi; Kashiwagi, Mieko; Tobari, Hiroyuki; Watanabe, Kazuhiro; Grisham, L. R.*; NB Heating Technology Group
AIP Conference Proceedings 1655, p.060002_1 - 060002_10, 2015/04
Times Cited Count：6 Percentile：87.25(Physics, Applied)In this paper, the recent activities on the new test stand are reported toward demonstration of the long pulse production for 22A, 100s negative ion beams. As for the temperature control of the plasma grid, a prototype of the grid with cooling/heating by circulating a high-temperature fluorinated fluid has been improved to cover the full extraction area by using 5 segments of the PG. These grids were found to have a capability to control the temperature with a time constant of 10s as well as the prototype grid. As a result, 15A negative ion beams for 100s have been achieved.
ion beam for ITERUmeda, Naotaka; Kojima, Atsushi; Kashiwagi, Mieko; Tobari, Hiroyuki; Hiratsuka, Junichi; Watanabe, Kazuhiro; Dairaku, Masayuki; Yamanaka, Haruhiko; Hanada, Masaya
AIP Conference Proceedings 1655, p.050001_1 - 050001_10, 2015/04
For ITER neutral beam system, negative deuterium ion beam of 1 MeV, 40 A (current density of 200 A/m) is required for 3600 s. To demonstrate ITER relevant negative ion beam acceleration, beam acceleration test has been carried out at MeV test facility in JAEA. The present target is H ion beam acceleration up to 1 MeV with 200 A/m for 60 s, which beam energy and pulse length are the present facility limit. To extend pulse duration time up to facility limit at high power density beam, new extraction grid has been developed with high cooling capability, which electron suppression magnet is placed under cooling channel. In addition, the aperture size of the electron suppression grid is enlarged from 14 mm to 16 mm and the aperture displacement is modified to reduce collision of negative ion beam on the grid. By these modifications, total grid power loading has reduced from 14% to 11%. As a result, beam acceleration up to 60 s which is the facility limit, has achieved at 700 kV, 100 A/m of negative ion beam without breakdown.
Hiratsuka, Junichi; Hanada, Masaya; Umeda, Naotaka; Kojima, Atsushi; Kashiwagi, Mieko; Watanabe, Kazuhiro; Tobari, Hiroyuki; Yoshida, Masafumi
Plasma and Fusion Research (Internet), 10(Sp.2), p.3405045_1 - 3405045_4, 2015/04
To produce high current density (
200 A/m), high-energy ( 1 MeV) negative ion beams for long pulse duration time (1 hour) for International Thermo-nuclear Experimental Reactor (ITER), the suppression of the direct interception of the negative ions with the grids has been carefully investigated with studying the deflection angle by aperture displacement technique. The non-linear dependence of the deflection angle appears at the aperture diameter of 14 mm on a steering control grid (SCG). From this dependence, the aperture diameter and the offset distance of the SCG has been designed to be 16 mm and 0.7 mm, respectively and tested in a prototype accelerator for ITER. Each of the beamlets on the multiple apertures is properly steered with compensation of the deflection due to the residual magnetic field in the accelerator and the grid power loading was significantly reduced. It resulted in a 10% enhancement of the accelerated beam current.
Kojima, Atsushi; Hanada, Masaya; Yoshida, Masafumi; Tobari, Hiroyuki; Kashiwagi, Mieko; Umeda, Naotaka; Watanabe, Kazuhiro; Grisham, L. R.*
Review of Scientific Instruments, 85(2), p.02B312_1 - 02B312_5, 2014/02
Times Cited Count：12 Percentile：48.5(Instruments & Instrumentation)The negative ion source for JT-60SA is designed to produce high power and long pulse beams with a beam energy of 500 keV, a negative ion current of 22A and a pulse duration of 100s. One of the key issues toward long pulse production of such high-current beams is the control of the surface temperature on the plasma grid (PG) where cesium is layered. In order to optimize cesium layer on PG for long pulse duration, we have developed an actively cooled PG where fluorinated fluids having high boiling point of 270
C is circulated. While the surface temperature of the PG in the JT-60 negative ion source has been kept at 170C for 100s with ramp-up time of 7s, stable long pulse beam extractions of 100s have been obtained. This current density is 90% of the required current density for JT-60 SA. The further increase of the current density is expected by optimizing the arc discharge power.
ion beams for ITER NB acceleratorUmeda, Naotaka; Kashiwagi, Mieko; Taniguchi, Masaki; Tobari, Hiroyuki; Watanabe, Kazuhiro; Dairaku, Masayuki; Yamanaka, Haruhiko; Inoue, Takashi; Kojima, Atsushi; Hanada, Masaya
Review of Scientific Instruments, 85(2), p.02B304_1 - 02B304_3, 2014/02
Times Cited Count：12 Percentile：48.5(Instruments & Instrumentation)In order to realize neutral beam systems in ITER whose target is to produce D ion beam of 1 MeV, 200 A/m during 3600s, the electrostatic five-stages negative ion accelerator has been developed at JAEA. To extend pulse length, heat load of the acceleration grids was reduced by controlling the ion beam trajectory. Namely, the beam deflection due to the residual magnetic filter in the accelerator was suppressed with the newly developed extractor with a 0.5 mm off-set aperture displacement. The use of new extractor improved the deflection angle from 6 mrad to 1 mrad, resulting in the reduction of direct interception of negative ions from 23% to 15% of the total acceleration power, respectively. As a result, the pulse length of 130 A/m, 881 keV H ion beam has been successfully extended from a previous value of 0.4s to 8.7s.
Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Kojima, Atsushi; Yoshida, Masafumi; Taniguchi, Masaki; Dairaku, Masayuki; Maejima, Tetsuya; Yamanaka, Haruhiko; Watanabe, Kazuhiro; et al.
Review of Scientific Instruments, 85(2), p.02B320_1 - 02B320_3, 2014/02
Times Cited Count：29 Percentile：75.28(Instruments & Instrumentation)The negative ion extractor for high power and long-pulse operations is newly developed toward the neutral beam injector (NBI) for heating & current drive of future fusion machines such as ITER, JT-60 Super Advanced (SA) and DEMO reactor. The satisfactory cooling capability is designed in the thermal analysis. A negative ion production and a suppression of electrons are experimentally validated for this new extractor. As the results, the negative ion current shows increases by a factor of 1.3 with suppressing the electron current. The beam divergence angle is also maintained small enough, 4 mrad.
Tobari, Hiroyuki; Inoue, Takashi; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Dairaku, Masayuki; Yamanaka, Haruhiko; Watanabe, Kazuhiro; Sakamoto, Keishi; Kuriyama, Masaaki*; et al.
Fusion Engineering and Design, 88(6-8), p.975 - 979, 2013/10
Times Cited Count：1 Percentile：10.69(Nuclear Science & Technology)The HV bushing, one of the ITER NB components, which is to be procured by JADA, is a multi-conductor feed through composed of five-stage double-layered insulator columns with large brazed ceramic ring and fiber reinforced plastic (FRP) ring. The HV bushing is a bulk head between insulation gas at 0.6 MPa and vacuum. The FRP ring is required to sustain the pressure load, seismic load and dead weight. Brazing area of the ceramic ring with Kovar is required to maintain vacuum leak tightness and pressure tightness against the air filled at 0.6 MPa. To design the HV bushing satisfying the safety factor of 
3.5, mechanical analyses were carried out. As for the FRP ring, it was confirmed that isotropic fiber cloth FRP rings should be used for sufficient strength against shear stress. Also, shape and fixation area of the Kovar sleeve were modified to lower the stress at the joint area. As a result, a design of the insulator for the HV bushing was established satisfying the requirement.
Kojima, Atsushi; Hanada, Masaya; Yoshida, Masafumi; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Grisham, L. R.*; et al.
Fusion Engineering and Design, 88(6-8), p.918 - 921, 2013/10
Times Cited Count：6 Percentile：44.02(Nuclear Science & Technology)In this paper, the recent activities are reported toward demonstration of the long pulse production. As for the improvement of uniform beam current profile, a symmetric magnetic field configuration for the source plasma production, a so-called tent-shaped filter, was found to be effective to improve the uniformity of the beam current profile. A similar configuration is applied to the JT-60 negative ion source whose plasma size is 1220 mm 
564 mm. An estimation from trajectory calculations of primary electrons with the symmetric magnetic field configuration showed that the primary electrons were distributed uniformly in a longitudinal direction. As for the temperature control of the plasma grid, a prototype of the grid with cooling/heating by circulating a high-temperature fluorinated fluid has been developed. This grid was found to have a capability to control the temperature with a time constant of 10 s by considering the physical properties of the fluid.
Kashiwagi, Mieko; Taniguchi, Masaki; Umeda, Naotaka; Dairaku, Masayuki; Tobari, Hiroyuki; Yamanaka, Haruhiko; Watanabe, Kazuhiro; Inoue, Takashi; DeEsch, H. P. L.*; Grisham, L. R.*; et al.
AIP Conference Proceedings 1515, p.227 - 236, 2013/02
Times Cited Count：12 Percentile：96.1(Physics, Applied)In a five stage multi-aperture multi-grid (MAMuG) accelerator for the ITER neutral beam injector (NBI), 1 MeV, 40 A D
ion beam is required for 1 hour. However, beamlets are deflected due to (1) magnetic field for electron suppression and (2) space charge repulsion between beamlets, and consequently, cause excess grid heat load. A three dimensional beam analysis has been carried out to compensate the beamlet deflections. This paper shows that the beamlet deflections due to (1) and (2) are compensated by an aperture offset of only 0.6 mm applied to the aperture of 17 mm in diameter in the extractor and by a metal bar attached around aperture area beneath the extractor, respectively. When the metal bar is increased to 3 mm in thickness and installed 30 mm away from the aperture area, the beamlet is steered gently by the weaker electric field distortion. The beam optics was confirmed not deteriorated by those compensations. The presentation also discusses application of these compensation techniques to the ITER design.
Shibata, Takanori; Terasaki, Ryo*; Kashiwagi, Mieko; Inoue, Takashi; Dairaku, Masayuki; Taniguchi, Masaki; Tobari, Hiroyuki; Umeda, Naotaka; Watanabe, Kazuhiro; Sakamoto, Keishi; et al.
AIP Conference Proceedings 1515, p.177 - 186, 2013/02
Times Cited Count：8 Percentile：92.97(Physics, Applied)In the neutral beam injector in JT-60SA, one of issues is that negative ion beam is partially intercepted at acceleration grids due to a spatial non-uniformity of negative ion production on large extraction area (0.90.45m). Previous experiments showed that fast electrons emitted from filament cathodes are transported in a longitudinal direction by 
drift and the spatial distribution of electron temperature (
) strongly relates with the non-uniformity. In this study, a three-dimensional electron transport analysis has been developed. Electron temperature in the analysis agreed well with measurements in JAEA 10A ion source. This study clarified that the bias of distribution are caused by the following reasons; (1) fast electrons drifted in the longitudinal direction survives near the end wall with energy up to 
= 25-60 eV and (2) they produces thermal electrons by collision with plasma particles there.
H ion beam acceleration at JAEA for the ITER neutral beam injectorTobari, Hiroyuki; Taniguchi, Masaki; Kashiwagi, Mieko; Dairaku, Masayuki; Umeda, Naotaka; Yamanaka, Haruhiko; Tsuchida, Kazuki; Takemoto, Jumpei; Watanabe, Kazuhiro; Inoue, Takashi; et al.
Plasma Science and Technology, 15(2), p.179 - 183, 2013/02
Times Cited Count：1 Percentile：4.39(Physics, Fluids & Plasmas)Vacuum insulation is a common issue for the accelerator and the HV bushing for the ITER NBI. The HV bushing has five-stage structure and each stage consists of double-layered insulators. Hence, several triple points exist around the insulators. To reduce electric field at those points simultaneously, three types of stress ring were developed. In voltage holding test of a full-scale mockup equipped with those stress rings, 120% of rated voltage was sustained and the voltage holding capability required in ITER was verified. In the MeV accelerator, voltage holding capability was not sufficient due to breakdown triggered by electric field concentration at edge and corner on grid components. By extending gap length, 1 MV was sustained in vacuum. Furthermore, with new accelerator grids which compensates beam deflection due to magnetic field and space charge repulsion between beamlets, 980 keV, 185 A/m H ion beam acceleration was demonstrated, which was close to ITER requirement.
Kojima, Atsushi; Hanada, Masaya; Hilmi, A.*; Inoue, Takashi; Watanabe, Kazuhiro; Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Tobari, Hiroyuki; Kobayashi, Shinichi*; et al.
Review of Scientific Instruments, 83(2), p.02B117_1 - 02B117_5, 2012/02
Times Cited Count：17 Percentile：60.55(Instruments & Instrumentation)Production of 500 keV, 3 A beams has been successfully achieved in the JT-60 negative by overcoming the low voltage holding of the accelerator. Toward the design of next ion source, database for the voltage holding capability based on experimental results is required and obtained. As a result, the voltage holding capability was found to vary with 67 N power of -0.15 and with 31.7 S power of -0.125 where N is the aperture number and S is the anode surface area. When N = 1100 and S = 2 m are applied to the design of JT-60SA ion source, the factors C are estimated to be 23 and 29, respectively. Therefore, the influence of the local electric field around the apertures is stronger than that of the surface area.
Taniguchi, Masaki; Kashiwagi, Mieko; Umeda, Naotaka; Dairaku, Masayuki; Takemoto, Jumpei; Tobari, Hiroyuki; Tsuchida, Kazuki; Yamanaka, Haruhiko; Watanabe, Kazuhiro; Kojima, Atsushi; et al.
Review of Scientific Instruments, 83(2), p.02B121_1 - 02B121_3, 2012/02
Times Cited Count：11 Percentile：46.97(Instruments & Instrumentation)JAEA has developed the MeV accelerator to demonstrate 1 MeV, 200 A/m H ion beam acceleration required for ITER NBI. A key to realize such a high power accelerator is improvement of voltage holding capability. Based on detailed investigation of the voltage holding characteristics, MeV accelerator was modified to reduce electric field concentration by extending gaps between the grid supports and increasing curvature radiuses at the support corners. After the modifications, accelerator succeeded in sustaining -1 MV in vacuum without beam acceleration. Moreover, beam deflection due to the magnetic field for electron suppression and space charge repulsion was compensated by aperture displacement technique. As the result, beam deflection was compensated and voltage holding during the beam acceleration was improved. Beam parameter of the MeV accelerator was increased to 980 keV, 185 A/m, which is close to the requirement of ITER accelerator.
Shibata, Takanori; Koga, Shojiro*; Terasaki, Ryo*; Inoue, Takashi; Dairaku, Masayuki; Kashiwagi, Mieko; Taniguchi, Masaki; Tobari, Hiroyuki; Tsuchida, Kazuki; Umeda, Naotaka; et al.
Review of Scientific Instruments, 83(2), p.02A719_1 - 02A719_3, 2012/02
Times Cited Count：2 Percentile：12.31(Instruments & Instrumentation)In the NBI for large fusion devices, production of uniform negative ion beam is one of important issues. A physical model is proposed to understand the non-uniformity. It has been qualitatively shown that the non-uniform beam intensity is due to the following process; (1) formation of non-uniform EEDF, (2) localized production of hydrogen atoms/ions (H
/H
) due to (1), (3) non-uniform flux of H/H to the PG and (4) localized surface production of negative ions. However, in the past studies, the EEDF was assumed as two temperature Maxwellian distribution from measurements. Thus effects of high energy electrons are not taken into account precisely. In the present research, local EEDF is calculated by the 3D Monte-Carlo kinetic model which takes into account the spatial and magnetic configurations of the real negative ion source. The numerical result show that high energy component of the EEDF enhances the spatial non-uniformity in the production rate of H/H.
