Development and validation of analysis code for spallation products behavior in LBE coolant system of ADS comparing with the distribution data in MEGAPIE spallation target

Miyahara, Shinya*; Arita, Yuji*; Nakano, Keita; Maekawa, Fujio; Sasa, Toshinobu; Obayashi, Hironari; Takei, Hayanori

Nuclear Engineering and Design, 403, p.112147_1 - 112147_17, 2023/03

https://doi.org/10.1016/j.nucengdes.2022.112147

It is important to evaluate the inventories and the release and transport behavior of the spallation products (SPs) in the Lead-Bismuth Eutectic (LBE) coolant system of Accelerator Driven System (ADS) for the safety studies of the radiological hazard both in the cases of normal operation and accident. University of Fukui and JAEA have been developing the computer analysis code TRAIL (Transport of RAdionuclides In Liquid metal systems) which predicts the time dependent behavior of SPs within the LBE coolant system of ADS for the wide range of operational events. The source term of both radioactive and stable SPs in the LBE coolant is given as input and the radioactive decay chain model for the radioactive SPs is implemented in the code to evaluate the effect of precursors on the SPs mobility. This paper presents the recent advancement status of the code development and the validation results comparing with the distribution data of volatile SPs in MEGAPIE spallation target.

A Study on removal mechanisms of cesium aerosol from noble gas bubble in sodium pool, 3; Measurement of decontamination factors in water simulation test

Koie, Ryusuke*; Kawaguchi, Munemichi*; Miyahara, Shinya*; Uno, Masayoshi*; Seino, Hiroshi

Proceedings of 29th International Conference on Nuclear Engineering (ICONE 29) (Internet), 4 Pages, 2022/08

In order to investigate removal mechanisms of cesium aerosol from noble gas bubble in sodium pool, we performed a water simulation test to measure the decontamination factors of simulant aerosols with nitrogen gas bubbles rising through the water pool. As a result, it was found that the decontamination factors increased with the increase in the aerosol diameter and the water pool depth.

Estimation of flow field in natural convection with density stratification by local ensemble transform Kalman filter

Ishigaki, Masahiro*; Hirose, Yoshiyasu; Abe, Satoshi; Nagai, Toru*; Watanabe, Tadashi*

Fluids (Internet), 7(7), p.237_1 - 237_18, 2022/07

https://doi.org/10.3390/fluids7070237

Evaluation of multiaxial low cycle creep-fatigue life for Mod.9Cr-1Mo steel under non-proportional loading

Nakayama, Yuta*; Ogawa, Fumio*; Hiyoshi, Noritake*; Hashidate, Ryuta; Wakai, Takashi; Ito, Takamoto*

ISIJ International, 61(8), p.2299 - 2304, 2021/08

https://doi.org/10.2355/isijinternational.ISIJINT-2020-780

This study discusses the creep-fatigue strength for Mod.9Cr-1Mo steel at a high temperature under multiaxial loading. A low-cycle fatigue tests in various strain waveforms were performed with a hollow cylindrical specimen. The low cycle fatigue test was conducted under a proportional loading with a fixed axial strain and a non-proportional loading with a 90-degree phase difference between axial and shear strains. The low cycle fatigue tests at different strain rates and the creep-fatigue tests at different holding times were also conducted to discuss the effects of stress relaxation and strain holding on the failure life. In this study, two types of multiaxial creep-fatigue life evaluation methods were proposed: the first method is to calculate the strain range using Manson's universal slope method with considering a non-proportional loading factor and creep damage; the second method is to calculate the fatigue damage by considering the non-proportional loading factor using the linear damage law and to calculate the creep damage from the improved ductility exhaustion law. The accuracy of the evaluation methods is much better than that of the methods used in the evaluation of actual machines such as time fraction rule.

Analytical study on removal mechanisms of cesium aerosol from a noble gas bubble rising through liquid sodium pool, 2; Effects of particle size distribution and agglomeration in aerosols

Miyahara, Shinya*; Kawaguchi, Munemichi; Seino, Hiroshi; Atsumi, Takuto*; Uno, Masayoshi*

Proceedings of 28th International Conference on Nuclear Engineering (ICONE 28) (Internet), 6 Pages, 2021/08

https://doi.org/10.1115/ICONE28-63286

In a postulated accident of fuel pin failure of sodium cooled fast reactor, a fission product cesium will be released from the failed pin as an aerosol such as cesium iodide and/or cesium oxide together with a fission product noble gas such as xenon and krypton. As the result, the xenon and krypton released with cesium aerosol into the sodium coolant as bubbles have an influence on the removal of cesium aerosol by the sodium pool in a period of bubble rising to the pool surface. In this study, cesium aerosol removal behavior due to inertial deposition, sedimentation and diffusion from a noble gas bubble rising through liquid sodium pool was analyzed by a computer program which deals with the expansion and the deformation of the bubble together with the aerosol absorption considering the effects of particle size distribution and agglomeration in aerosols. In the analysis, initial bubble diameter, sodium pool depth and temperature, aerosol particle diameter and density, initial aerosol concentration in the bubble were changed as parameter, and the results for the sensitivities of these parameters on decontamination factor (DF) of cesium aerosol were compared with the results of the previous study in which the effects of particle size distribution and agglomeration in aerosols were not considered. From the results, it was concluded that the sensitivities of initial bubble diameter, the aerosol particle diameter and density to the DF became significant due to the inertial deposition of agglomerated aerosols. To validate these analysis results, the simulation experiments have been conducted using a simulant particles of cesium aerosol under the condition of room temperature in water pool and air bubble systems. The experimental results were compared with the analysis results calculated under the same condition.

Phase-field model for crystallization in alkali disilicate glasses; LiO-2SiO, NaO-2SiO and KO-2SiO

Kawaguchi, Munemichi; Uno, Masayoshi*

Journal of the Ceramic Society of Japan, 128(10), p.832 - 838, 2020/10

https://doi.org/10.2109/jcersj2.20145

This study developed phase-field method (PFM) technique in oxide melt system by using a new mobility coefficient (). The crystal growth rates () obtained by the PFM calculation with the constant were comparable to the thermodynamic driving force in normal growth model. The temperature dependence of the was determined from the experimental crystal growth rates and the . Using the determined , the crystal growth rates () in alkali disilicate glasses, LiO-2SiO, NaO-2SiO and KO-2SiO were simulated. The temperature dependence of the was qualitatively and quantitatively so similar that the PFM calculation results demonstrated the validity of the . Especially, the obtained by the PFM calculation appeared the rapid increase just below the thermodynamic melting point () and the steep peak at around -100 K. Additionally, as the temperature decreased, the apparently approached zero ms, which is limited by the representing the interface jump process. Furthermore, we implemented the PFM calculation for the variation of the parameter in the . As the increased from zero to two, the peak of the became steeper and the peak temperature of the shifted to the high temperature side. The parameters and in the increased exponentially and decreased linearly as the atomic number of the alkali metal increased due to the ionic potential, respectively. This calculation revealed that the and in the were close and reasonable for each other.

A Study on sodium-concrete reaction in presence of internal heating

Kawaguchi, Munemichi; Miyahara, Shinya*; Uno, Masayoshi*

Journal of Nuclear Engineering and Radiation Science, 6(2), p.021305_1 - 021305_9, 2020/04

https://doi.org/10.1115/1.4045898

Sodium-concrete reaction (SCR) is one of the important phenomena during severe accidents in sodium-cooled fast reactors (SFRs) owing to the generation of large sources of hydrogen and aerosols in the containment vessel. In this study, SCR experiments with an internal heater were performed to investigate the chemical reaction beneath the internal heater (800C), which was used to simulate the obstacle and heating effect on SCR. Furthermore, the effects of the internal heater on the self-termination mechanism were discussed. The internal heater on the concrete hindered the transport of Na into the concrete. Therefore, Na could start to react with the concrete at the periphery of the internal heater, and the concrete ablation depth at the periphery was larger than under the internal heater. The high Na pool temperature of 800C increased largely the Na aerosol release rate, which was explained by Na evaporation and hydrogen bubbling, and formed the porous reaction product layer, whose porosity was 0.54-0.59 from the mass balance of Si and image analyzing EPMA mapping. They had good agreement with each other. The porous reaction products decreased the amount of Na transport into the reaction front. The Na concentration around the reaction front became about 30wt.% despite the position of the internal heater. It was found that the Na concentration condition was one of the dominant parameters for the self-termination of SCR, even in the presence of the internal heater.

The Analytical study of inventories and physicochemical configuration of spallation products produced in Lead-Bismuth Eutectic of Accelerator Driven System

Miyahara, Shinya*; Ohdaira, Naoya*; Arita, Yuji*; Maekawa, Fujio; Matsuda, Hiroki; Sasa, Toshinobu; Meigo, Shinichiro

Nuclear Engineering and Design, 352, p.110192_1 - 110192_8, 2019/10

https://doi.org/10.1016/j.nucengdes.2019.110192

Lead-Bismuth Eutectic (LBE) is used as a spallation neutron target and coolant materials of Accelerator Driven System (ADS), and many kinds of elements are produced as spallation products. It is important to evaluate the release and transport behavior of the spallation products in the LBE. The inventories and the physicochemical composition of the spallation products produced in LBE have been investigated for an LBE loop in the ADS Target Test Facility (TEF-T) in J-PARC. The inventories of the spallation products in the LBE were estimated using the PHITS code. The physicochemical composition of the spallation products in the LBE was calculated using the Thermo-Calc code under the conditions of the operation temperatures of LBE from 350C to 500C and the oxygen concentrations in LBE from 10 ppb to 1 ppm. The calculation showed that the 5 elements of Rb, Tl, Tc, Os, Ir, Pt, Au and Hg were soluble in LBE under the all given conditions and any kinds of compound were not formed in LBE. It was suggested that the oxides of Ce, Sr, Zr and Y were stable as CeO, SrO, ZrO and YO in the LBE.

Melting behavior and thermal conductivity of solid sodium-concrete reaction product

Kawaguchi, Munemichi; Miyahara, Shinya; Uno, Masayoshi*

Journal of Nuclear Science and Technology, 56(6), p.513 - 520, 2019/06

https://doi.org/10.1080/00223131.2019.1599744

This study revealed melting points and thermal conductivities of four samples generated by sodium-concrete reaction (SCR). We prepared the samples using two methods such as firing mixtures of sodium and grinded concrete powder, and sampling depositions after the SCR experiments. In the former, the mixing ratios were determined from the past experiment. The latter simulated the more realistic conditions such as the temperature history and the distribution of Na and concrete. The thermogravimetry-differential thermal analyzer (TG-DTA) measurement showed the melting points were 865-942C, but those of the samples containing metallic Na couldn't be clarified. In the two more realistic samples, the compression moldings in a furnace were observed. The observation revealed the softening temperature was 800-840C and the melting point was 840-850C, which was 10-20C lower than the TG-DTA results. The thermodynamics calculation of FactSage 7.2 revealed the temperature of the onset of melting was caused by melting of the some components such as NaSiO and/or NaSiO. Moreover, the thermal conductivity was =1-3W/m-K, which was comparable to xNaO-1-xSiO (x=0.5, 0.33, 0.25), and those at 700C were explained by the equation of .

Analyses of LSTF experiment and PWR plant for 5% cold-leg break loss of coolant accident

Watanabe, Tadashi*; Ishigaki, Masahiro*; Katsuyama, Jinya

Proceedings of 12th International Topical Meeting on Nuclear Reactor Thermal-Hydraulics, Operation and Safety (NUTHOS-12) (USB Flash Drive), 9 Pages, 2018/10

The analyses of LSTF experiment and PWR plant for 5% cold-leg break LOCA are performed using the RELAP5/MOD3.3 code. The discharge coefficient of critical flow model is determined so as to obtain the agreement of pressure transient between the LSTF experiment and the experimental analysis, and used for the PWR analysis. The characteristics of thermal-hydraulic phenomena in the experiment are shown to be simulated well by the two analyses. The decrease in core differential pressure during the loop-seal clearing is, however, underestimated by the two analyses, and the core heat up is not predicted. The loop flow rates are also underestimated by the two analyses. Although the duration of core heat up during the boil-off period is longer in the experimental analysis, the results of two analyses agree well, and the effect of scaling is found to be small between the experimental analysis and the PWR analysis.