Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Ebihara, Kenichi; Sekine, Daiki*; Sakiyama, Yuji*; Takahashi, Jun*; Takai, Kenichi*; Omura, Tomohiko*
International Journal of Hydrogen Energy, 48(79), p.30949 - 30962, 2023/09
Times Cited Count：0 Percentile：0.01(Chemistry, Physical)To understand hydrogen embrittlement (HE), which is one of the stress corrosion cracking of steel materials, it is necessary to know the H distribution in steel, which can be effectively interpreted by numerical simulation of thermal desorption spectra. In weld metals and TRIP steels, residual austenite significantly influences the spectra, but a clear H distribution is not well known. In this study, an originally coded two-dimensional model was used to numerically simulate the previously reported spectra of high-carbon ferritic-austenitic duplex stainless steels, and it was found that H is mainly trapped at the carbide surface when the amount of H in the steel is low and at the duplex interface when the amount of H is high. It was also found that the thickness dependence of the H desorption peak for the interface trap site is caused by a different reason than the conventional one.
Hirota, Noriaki; Takeda, Kiyoko*; Tachibana, Yukio; Masaki, Yasuhiro*
Zairyo To Kankyo, 70(3), p.68 - 76, 2021/03
Corrosion resistance of stainless steels and Ni-based alloys were evaluated in a sulfuric acid decomposition gas at high temperature. The evaluation were carried out in an environment simulated in the sulfuric acid decomposition reaction vessel for thermochemical hydrogen production process (IS process). Their corrosion films were also analyzed for better understanding of the corrosion behavior. As a result, after 100 hour corrosion test, Ni-based alloy containing 2.4% Si showed good corrosion resistance. Ferritic stainless steel containing 3% Al (3Al-Ferrite) showed better corrosion resistance. Its corrosion rate was lower than that of SiC (0.1mm/year), which is a candidate material for the sulfuric acid decomposition reaction vessel. On the other hand, Ni-based alloy pre-filmed with Al
O
is prepared as the relative corrosion film of 3Al-Ferrite. Its corrosion rate was significantly higher than that of 3Al-Ferrite. As the result of EPMA analysis of these oxide films, Ni-based alloy containing 2.4% Si formed Si oxide film which had some cracks after the long term corrosion test. Therefore S penetrated into grain boundaries of the matrix through the oxide film. 3Al-Ferrite formed a thin and uniform AlO film, and the penetration of S into the grain boundaries was not observed. AlO pre-film of Ni-based alloy also showed S penetration in the matrix because the AlO pre-film had many small defects originally. The corrosion oxide film of 3Al-Ferrite consisted of only 
-AlO, while the AlO pre-film consist of -AlO and 
-AlO. Those results suggest that the better corrosion resistance of 3Al-Ferrite is due to the uniform formation of dense -AlO film at the early stage of the corrosion.
- dual phase steelEbihara, Kenichi; Sekine, Daiki*; Sakiyama, Yuji*; Takahashi, Jun*; Takai, Kenichi*; Omura, Tomohiko*
no journal, ,
Hydrogen embrittlement (HE) in high-strength steels and advanced high-strength steels is a phenomenon that must be understood for its prediction and prevention. Since the austenite phase ( phase) in these steels traps more H than the matrix phase, its effect on HE is of concern. In this study, we numerically reproduced the previously reported H thermal desorption spectra of a high-carbon - duplex stainless steel specimen to clarify the H-trapping defects in the specimen. The results show that H is trapped at the carbide surface when the amount of H inside the sample is low, but that the amount of H trapped at the phase surface increases as the H content increases, and that H trapped inside the phase is desorbed at relatively low temperatures. It was also found that the H entry simulation may not yield an appropriate pre-temperature initial H distribution. The conference will address this point.
