MAAP code analysis for the in-vessel phase of Fukushima-Daiichi Nuclear Power Station Unit 1 and comparison of the results among Units 1 to 3

Sato, Ikken; Yoshikawa, Shinji; Yamashita, Takuya; Shimomura, Kenta; Cibula, M.*; Mizokami, Shinya*

Nuclear Engineering and Design, 422, p.113088_1 - 113088_24, 2024/06

https://doi.org/10.1016/j.nucengdes.2024.113088

Effect of preparation conditions and storage time on characteristic and rheological properties of carbonate slurries

Kato, Tomoaki; Yamagishi, Isao

JAEA-Technology 2023-018, 53 Pages, 2023/11

JAEA-Technology-2023-018.pdf:2.6MB

In the decommissioning of Fukushima Daiichi Nuclear Power Station, radioactive carbonate slurry waste was generated using the Advanced Liquid Processing System (ALPS) pretreatment and temporarily stored in a high integrity container (HIC). In 2015, overflow of supernatant from HIC estimate as bubble retention in the carbonate slurry was discovered, increasing the need for a safety assessment of the carbonate slurry stored the HIC (HIC slurry). In this study, a carbonate slurry (simulated slurry) was prepared according to the Mg/Ca mass ratio in the ALPS inlet water of the HIC slurry which overflew the HIC. The effects of reaction time during the pretreatment process, suspended solids concentration (SS concentration), and settling time on the particle composition, morphology and rheological properties of the slurry were investigated. Evaluating the effect of reaction time and concentration process on chemical properties in slurry production, the effect of the reaction time was not confirmed in the simulated slurry that had undergone the concentration process, and slurry prepared at SS concentration of 150 g/L was composed of formless particles have a particle diameter of 0.4 m or less. We also investigate the effect of SS concentration on sedimentability, decrease in SS concentration by dilution with processing solution contributed to an increase in the initial slurry settling velocity. Furthermore, two different flow characteristics were observed depending on the settling time, suggesting that the slurry at the initial settling time has non-Bingham flow properties, whereas it changes to Bingham flow properties as the settling time becomes longer. In addition, yield stress was increased with settling time, and this yield stress was found to be exponentially proportional to the density of the slurry. These results provide knowledge to estimate the current state of HIC slurry and are expected to contribute to the safety assessment.

MAAP code analysis focusing on the fuel debris condition in the lower head of the pressure vessel in Fukushima-Daiichi Nuclear Power Station Unit 2

Sato, Ikken; Yoshikawa, Shinji; Yamashita, Takuya; Cibula, M.*; Mizokami, Shinya*

Nuclear Engineering and Design, 404, p.112205_1 - 112205_21, 2023/04

https://doi.org/10.1016/j.nucengdes.2023.112205

Based on updated knowledge from plant-internal investigations, experiments and model simulations until now, the in-vessel phase of Fukushima-Daiichi Nuclear Power Station Unit 2 was analyzed using the MAAP code. In Unit 2, it is considered that the core material enthalpy was relatively low when it relocated to the lower plenum of the pressure vessel, then, cooled by the coolant and solidified there. Although the MAAP code tended to underestimate the degree of core-material oxidation during the relocation, this probable underestimation was compensated for by an existing study that was considered more reliable, so that more realistic debris conditions in the lower plenum could be obtained. Basic validity of the former prediction of the Unit 2 accident progression behavior was confirmed and detailed boundary condition for the later phase was provided. This boundary condition should be utilized for future studies addressing debris reheating process leading to lower head failure and debris relocation toward the pedestal.

Radiation imaging using an integrated radiation imaging system based on a compact Compton camera under Unit 1/2 exhaust stack of Fukushima Daiichi Nuclear Power Station

Sato, Yuki; Terasaka, Yuta

Journal of Nuclear Science and Technology, 59(6), p.677 - 687, 2022/06

https://doi.org/10.1080/00223131.2021.2001391

Preparation of carbonate slurry simulating chemical composition of slurry in overflowed high integrity container and evaluation of its characteristics

Horita, Takuma; Yamagishi, Isao; Nagaishi, Ryuji; Kashiwaya, Ryunosuke*

JAEA-Technology 2021-012, 34 Pages, 2021/07

JAEA-Technology-2021-012.pdf:2.1MB
JAEA-Technology-2021-012(errata).pdf:0.18MB

Waste mainly consisting of carbonate precipitates (carbonate slurry) from the Advanced Liquid Processing System (ALPS) and the improved ALPS at the Fukushima Daiichi Nuclear Power Station of Tokyo Electric Power Holdings, Inc. have been storing in the High Integrity Container (HIC). The supernatant solution of carbonate slurry contained in some of HICs were overflowed in April of 2015. The all of level of liquid in the HICs were investigated; however, almost of the HICs were under the level of overflow. The mechanism of overflow suggested to be depending on the difference of the properties of the carbonate slurry such as the retention/release characteristics of the bubbles. Therefore, in order to clarify the mechanism of leakage, the repeatability experiment was carried out by using simulated carbonate slurry. The simulated carbonate slurry was perpetrated by using the same cross-flow filter system of the actual ALPS. Moreover, the preparative conditions for the simulated carbonate slurry were the same as Mg/Ca concentration ratio in inlet water of the ALPS (raw water) and the ALPS operating conditions. The chemical characteristics of simulated carbonate slurries were revealed by ICP-AES, pH meter, etc. The density of the settled slurry layer tended to increase depending on the calcium concentration in the raw water. The bubble injection test was conducted in order to investigate the bubble retention/release behavior in the simulated carbonate slurry layer. The simulated carbonate slurry with high settling density, which was generated by high calcium concentration solution was revealed to retain the injected bubbles. Since the ratio of concentration calcium and magnesium during the carbonate slurry generation is assumed to affect the retention of bubbles in the slurry layer, the information on the composition of raw water is one of important factor for overflow of HICs.

Simple cation-exchange separation for ICP-MS measurement of Se in spent nuclear fuel sample

Asai, Shiho; Hanzawa, Yukiko; Suzuki, Hideya; Toshimitsu, Masaaki; Okumura, Keisuke; Shinohara, Nobuo; Kimura, Takaumi; Inagawa, Jun; Suzuki, Kensuke*; Kaneko, Satoru*

Proceedings of International Conference on Toward and Over the Fukushima Daiichi Accident (GLOBAL 2011) (CD-ROM), 5 Pages, 2011/12

Computational study for inventory estimation of Se-79, Tc-99, Sn-126, and Cs-135 in high-level radioactive wastes from spent nuclear fuels of light water reactors

Okumura, Keisuke; Asai, Shiho; Hanzawa, Yukiko; Okamoto, Tsutomu; Suzuki, Hideya; Toshimitsu, Masaaki; Inagawa, Jun; Kimura, Takaumi; Suzuki, Kensuke*; Kaneko, Satoru*

Proceedings of 14th International Conference on Environmental Remediation and Radioactive Waste Management (ICEM 2011) (CD-ROM), p.1443 - 1450, 2011/09

https://doi.org/10.1115/ICEM2011-59087

Inventory estimation of long-lived fission products (LLFPs) in high-level radioactive wastes (HLW) from spent nuclear fuels of light water reactors is important for a safety assessment of their disposal. In order to develop an inventory estimation method of difficult-to-measure LLFPs (Se-79, Tc-99, Sn-126, and Cs-135), a parametric study was carried out by using a sophisticated burnup calculation code and data. In the parametric study, fuel specifications and irradiation conditions are changed in the conceivable range. The considered parameters are fuel assembly types (PWR / BWR), U-235 enrichment, moderator temperature, void fraction, power density, and so on. From the calculated results, we clarify the burnup characteristics of the target LLFPs and their possible ranges of generations. Finally, candidates of the key nuclide are proposed for the scaling factor method of HLW.

Comparison of post-irradiation experimental data and theoretical calculations for inventory estimation of long-lived fission products in spent nuclear fuel

Asai, Shiho; Hanzawa, Yukiko; Okumura, Keisuke; Suzuki, Hideya; Toshimitsu, Masaaki; Shinohara, Nobuo; Kaneko, Satoru*; Suzuki, Kensuke*

Proceedings of 13th International Conference on Environmental Remediation and Radioactive Waste Management (ICEM 2010) (CD-ROM), p.261 - 264, 2010/10

https://doi.org/10.1115/ICEM2010-40101

Oxygen potentials of (AmNp)O

Otobe, Haruyoshi; Akabori, Mitsuo; Arai, Yasuo; Minato, Kazuo

Journal of the American Ceramic Society, 92(1), p.174 - 178, 2009/01

https://doi.org/10.1111/j.1551-2916.2008.02828.x

The oxygen potentials of the oxygen-deficient fluorite-type oxide AmPuO were measured by the electrochemical method with using a zirconia solid-electrolyte. The coulomb titration has been made for the sample at 1333 K over 0.02 0.25. The oxygen potentials were -93.63 and -440.18 kJmol for = 0.021 and 0.25 at 1333 K, respectively. The temperature dependence of the oxygen potentials was also measured between 1000 and 1333 K over the range of 0.02 0.243. The temperature dependence was almost linear over the and temperature ranges concerned.

Synthesis of americium trichloride by the reaction of americium nitride with cadmium chloride

Hayashi, Hirokazu; Takano, Masahide; Akabori, Mitsuo; Minato, Kazuo

Journal of Alloys and Compounds, 456(1-2), p.243 - 246, 2008/05

https://doi.org/10.1016/j.jallcom.2007.02.011

Americium trichloride was synthesized by the reaction of americium nitride with cadmium chloride at 600-660 K in a dynamic vacuum. The product was hexagonal AmCl, of which lattice parameters were determined to be = 0.7390 and = 0.4215 nm. The results indicate that high purity AmCl samples, in which the oxychloride was not found, were prepared without the use of corrosive reagents. The reaction of the nitrides with cadmium chloride is suitable for synthesis of high purity actinide and lanthanide chlorides.