Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Ukai, Shigeharu; Sakamoto, Kan*; Otsuka, Satoshi; Yamashita, Shinichiro; Kimura, Akihiko*
Journal of Nuclear Materials, 583, p.154508_1 - 154508_24, 2023/09
Times Cited Count：6 Percentile：91.18(Materials Science, Multidisciplinary)Nakanishi, Takumi*; Hori, Yuta*; Shigeta, Yasuteru*; Sato, Hiroyasu*; Kiyanagi, Ryoji; Munakata, Koji*; Ohara, Takashi; Okazawa, Atsushi*; Shimada, Rintaro*; Sakamoto, Akira*; et al.
Journal of the American Chemical Society, 145(35), p.19177 - 19181, 2023/08
Times Cited Count：1 Percentile：0(Chemistry, Multidisciplinary)Emura, Yuki; Takai, Toshihide; Kikuchi, Shin; Kamiyama, Kenji; Yamano, Hidemasa; Yokoyama, Hiroki*; Sakamoto, Kan*
Journal of Nuclear Science and Technology, 10 Pages, 2023/00
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)Asakura, Kazuki; Shimomura, Yusuke; Donomae, Yasushi; Abe, Kazuyuki; Kitamura, Ryoichi; Miyakoshi, Hiroyuki; Takamatsu, Misao; Sakamoto, Naoki; Isozaki, Ryosuke; Onishi, Takashi; et al.
JAEA-Review 2021-020, 42 Pages, 2021/10
JAEA-Review-2021-020.pdf:2.95MB
The disposal of radioactive waste from the research facility need to calculate from the radioactivity concentration that based on variously nuclear fuels and materials. In Japan Atomic Energy Agency Oarai Research and Development Institute, the study on considering disposal is being advanced among the facilities which generate radioactive waste as well as the facilities which process radioactive waste. This report summarizes a study result in FY2020 about the evaluation method to determine the radioactivity concentration in radioactive waste on Oarai Research and Development Institute.
Kikuchi, Shin; Takai, Toshihide; Yamano, Hidemasa; Sakamoto, Kan*
Proceedings of 28th International Conference on Nuclear Engineering (ICONE 28) (Internet), 9 Pages, 2021/08
In a postulated severe accidental condition of sodium-cooled fast reactor (SFR), eutectic melting between boron carbide (B
C) and stainless steel (SS) may occur. Thus, behavior of BC-SS eutectic melting is one of the phenomena to evaluate the core disruptive accidents in SFR. In this study, the reaction experiments using SS crucibles and the pellets of SS with low BC concentration as samples were performed to simulate the state of the reaction interface in which the eutectic reaction and interdiffusion of BC-SS have progressed to a certain extent. It was revealed that the rate constants of eutectic reaction between SS and SS with low BC concentration are smaller than that of BC-SS eutectic reaction at high temperatures.
Aghamiri, S. M. S.*; Sugawara, Naoya*; Ukai, Shigeharu; Ono, Naoko*; Sakamoto, Kan*; Yamashita, Shinichiro
Materials Characterization, 176, p.111043_1 - 111043_6, 2021/06
Advanced oxidation-resistant FeCrAl ODS alloys were developed via the control of composition-processing conditions for the accident tolerant fuel (ATF) cladding. For the first time, a single-crystal like recrystallized FeCrAl ODS alloy was achieved with a unique crystallographic texture of 110-plane and 211-direction and a high number density of fine nanoscale oxide particles. Evaluation of yield strengths at different temperatures showed higher values in transverse (T) direction than longitudinal (L) direction. The crystal orientation dependence of the yield strength up to 800
C was attributed to lower value of Schmid factor in transverse direction. Accordingly, the critical resolved shear stress of this practical class of advanced materials was calculated in various temperatures.
Kikuchi, Shin; Sakamoto, Kan*; Takai, Toshihide; Yamano, Hidemasa
Nihon Kikai Gakkai 2020-Nendo Nenji Taikai Koen Rombunshu (Internet), 4 Pages, 2020/09
In a postulated severe accidental condition of sodium-cooled fast reactor (SFR), eutectic melting between boron carbide (BC) as control rod element and stainless steel (SS) as control rod cladding or related structure may occur. Thus, behavior of BC-SS eutectic melting is one of the phenomena to evaluate the core disruptive accidents in SFR. In order to clarify the kinetic feature of BC-SS eutectic melting process in the interface, the thinning test for SS crucibles using the pellets of BC or SS with low BC concentration were performed to obtain the rate constant with dependence of BC concentration against SS. It was found that the rate constants of eutectic melting between SS and SS low BC concentration were smaller than that of BC-SS in the high temperature range. Besides, the rate constant of eutectic melting between SS and BC containing SS became small when decreasing the BC concentration against SS.
scattering length from 
photoproduction on the proton near the reaction thresholdIshikawa, Takatsugu*; Fujimura, Hisako*; Fukasawa, Hiroshi*; Hashimoto, Ryo*; He, Q.*; Honda, Yuki*; Hosaka, Atsushi; Iwata, Takahiro*; Kaida, Shun*; Kasagi, Jirota*; et al.
Physical Review C, 101(5), p.052201_1 - 052201_6, 2020/05
Times Cited Count：4 Percentile：44.35(Physics, Nuclear)Aghamiri, S. M. S.*; Sowa, Takashi*; Ukai, Shigeharu*; Ono, Naoko*; Sakamoto, Kan*; Yamashita, Shinichiro
Materials Science & Engineering A, 771, p.138636_1 - 138636_12, 2020/01
Times Cited Count：33 Percentile：90.54(Nanoscience & Nanotechnology)Oxide dispersion strengthened (ODS) FeCrAl ferritic steels are being developed as potential accident tolerance fuel cladding materials for the light water reactors (LWRs) due to significant improvement in steam oxidation by alumina forming scale and good mechanical properties up to high temperatures. In this study, the microstructural characteristics and tensile properties of the two FeCrAl ODS cladding tubes with different extrusion temperatures of 1100C and 1150C were investigated during processing conditions. While the hot extruded sample showed micron sized elongated grains with strong 
-fiber in 
110
texture, cold pilger rolling process change the microstructure to submicron/micron size grain structure along with texture evolution to both -fiber (110 texture) and 
-fiber ({111} texture) via crystalline rotations. Subsequently, final annealing resulted in evolution of microstructure to large grain recrystallized structure starting at recrystallization temperature of 
810-850C. Two distinct texture development happened in recrystallized cladding tubes, i.e., only large elongated grains of (110) 211 texture following extrusion temperature of 1100C; and two texture components of (110) 211 and {111} 112 following higher extrusion temperature of 1150C. The different texture development and retarding of recrystallization progress in 1100C-extruded cladding tubes were attributed to higher distribution of oxide particles.
Ohashi, Kunihide*; Hino, Takanori*; Kobayashi, Hiroshi*; Onodera, Naoyuki; Sakamoto, Nobuaki*
Journal of Marine Science and Technology, 24(3), p.884 - 901, 2019/09
Times Cited Count：17 Percentile：75.85(Engineering, Marine)An unsteady Reynolds averaged Navier-Stokes solver with a structured overset grid method has been developed. Velocity pressure coupling is achieved using an artificial compressibility approach, spatial discretization is based on a FVM. Body motions are considered using the grid deformation technique and grid velocities in the convective term. The full multigrid (FMG) method is applied to obtain fast convergence. The cell flag on a coarse grid level is determined using the cell flag on a fine grid level. In the coarse and fine grid level calculations at the FMG stage, the data are interpolated until the finest grid level is achieved at an overset update interval. Then, the data are updated based on the overset relations at the finest grid level and then transferred to a coarser grid level. The computations for flows around a hull form, including an unsteady simulation with regular waves, are demonstrated.
Yamashita, Shinichiro; Ioka, Ikuo; Nemoto, Yoshiyuki; Kawanishi, Tomohiro; Kurata, Masaki; Kaji, Yoshiyuki; Fukahori, Tokio; Nozawa, Takashi*; Sato, Daiki*; Murakami, Nozomu*; et al.
Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.206 - 216, 2019/09
After the nuclear accident at Fukushima Daiichi Power Plant, research and development (R&D) program for establishing technical basis of accident-tolerant fuel (ATF) started from 2015 in Japan. Since then, both experimental and analytical studies necessary for designing a new light water reactor (LWR) core with ATF candidate materials are being conducted within the Japanese ATF R&D Consortium for implementing ATF to the existing LWRs, accompanying with various technological developments required. Until now, we have accumulated experimental data of the candidate materials by out-of-pile tests, developed fuel evaluation codes to apply to the ATF candidate materials, and evaluated fuel behavior simulating operational and accidental conditions by the developed codes. In this paper, the R&D progresses of the ATF candidate materials considered in Japan are reviewed based on the information available such as proceedings of international conference and academic papers, providing an overview of ATF program in Japan.
Yamazaki, Saishun; Pshenichnikov, A.; Pham, V. H.; Nagae, Yuji; Kurata, Masaki; Tokushima, Kazuyuki*; Aomi, Masaki*; Sakamoto, Kan*
Proceedings of Annual Topical Meeting on Reactor Fuel Performance (TopFuel 2018) (Internet), 8 Pages, 2018/10
It is predictively evaluated that degradation of fuel assembly proceeded in a certain steam-starved condition at the early stage of a SA at 1F unit 2 (BWR). As for PWR fuel assembly, effective steam flow rate was properly indicated by normalizing to a unit of g-H
O/sec/rod which is used as an important parameter for evaluating fuel degradation progression. Due to the inhomogeneous configuration of BWR fuel assembly, the difference of Zry oxidation and hydrogen uptake between the inside and outside of the channel box cannot be properly evaluated by this normalization. Instead of g-HO/sec/rod, proper evaluation unit for BWR configuration is necessary. To accumulate Zry oxidation and hydrogen uptake data for steam-starved conditions, high temperature oxidation tests were performed using a simulated BWR fuel bundle sample. The use of equivalent diameter of the cross section of BWR fuel assembly was proposed for normalization of effective steam flow rate.
Takahatake, Yoko; Ambai, Hiromu; Sano, Yuichi; Takeuchi, Masayuki; Koizumi, Kenji; Sakamoto, Kan*; Yamashita, Shinichiro
Proceedings of Annual Topical Meeting on Reactor Fuel Performance (TopFuel 2018) (Internet), 9 Pages, 2018/10
The corrosion behaviour of FeCrAl-ODS steels for the accident tolerant fuel cladding of LWRs were investigated in nitric acid solutions for the reprocessing process of spent fuels. The corrosion tests were carried out at 60C, 80C and the boiling point of the solutions, and the specimens were then analysed by XPS. The corrosion remarkably progressed at the boiling point, and the highest corrosion rate was 0.22 mm/y. In the oxide film, the atomic concentration of Fe was lower, than that in the base material, and those of Cr and Al were higher. The results show that the corrosion of FeCrAl-ODS steels in hot nitric acid solution is not severe because of the high corrosion resistance of the oxide film formed on the material; hence, the corrosion resistance of the new cladding materials in the dissolution process of spent fuel is acceptable for reprocessing operations.
Kondo, Keietsu; Aoki, So; Yamashita, Shinichiro; Ukai, Shigeharu*; Sakamoto, Kan*; Hirai, Mutsumi*; Kimura, Akihiko*
Nuclear Materials and Energy (Internet), 15, p.13 - 16, 2018/05
Times Cited Count：18 Percentile：87.82(Nuclear Science & Technology)Radiation hardening and microstructural evolution of ion irradiated 12Cr-6Al ODS ferritic steel was studied. Ion irradiation experiments were performed using Fe ions up to the nominal displacement damage of 20 dpa at the irradiation temperature was 300C. The monotonical increase of radiation hardening with dose was confirmed by experimentally obtained hardness data. The radiation hardening was also calculated theoretically by introducing the microstructural character examined by TEM into the dispersed barrier hardening model. The results showed a good agreement with the experimentally obtained data up to 5 dpa, while a slight discrepancy was found between theoretical and experimental hardness values at 20 dpa. Radiation hardening was mainly caused by irradiation-induced defect clusters below the irradiation dose of 5 dpa. As the irradiation dose increased toward 20 dpa, an additional influence of the radiation appeared, which was assumed to be induced by ' phase transformation.
Muta, Hiroaki*; Nishikane, Ryoji*; Ando, Yusuke*; Matsunaga, Junji*; Sakamoto, Kan*; Harjo, S.; Kawasaki, Takuro; Oishi, Yuji*; Kurosaki, Ken*; Yamanaka, Shinsuke*
Journal of Nuclear Materials, 500, p.145 - 152, 2018/03
Times Cited Count：13 Percentile：76.73(Materials Science, Multidisciplinary)Yamashita, Shinichiro; Nagase, Fumihisa; Kurata, Masaki; Nozawa, Takashi; Watanabe, Seiichi*; Kirimura, Kazuki*; Kakiuchi, Kazuo*; Kondo, Takao*; Sakamoto, Kan*; Kusagaya, Kazuyuki*; et al.
Proceedings of 2017 Water Reactor Fuel Performance Meeting (WRFPM 2017) (USB Flash Drive), 10 Pages, 2017/09
In Japan, the research and development (R&D) project on accident tolerant fuel and other components (ATFs) of light water reactors (LWRs) has been initiated in 2015 for establishing technical basis of ATFs. The Japan Atomic Energy Agency (JAEA) has coordinated and carried out this ATF R&D project in cooperation with power plant providers, fuel venders and universities for making the best use of the experiences, knowledges in commercial uses of zirconium-base alloys (Zircaloy) in LWRs. ATF candidate materials under consideration in the project are FeCrAl steel strengthened by dispersion of fine oxide particles(FeCrAl-ODS) and silicon carbide (SiC) composite, and are expecting to endure severe accident conditions in the reactor core for a longer period of time than the Zircaloy while maintaining or improving fuel performance during normal operations. In this paper, the progresses of the R&D project are reported.
Takano, Sho*; Kusagaya, Kazuyuki*; Goto, Daisuke*; Sakamoto, Kan*; Yamashita, Shinichiro
Proceedings of 2017 Water Reactor Fuel Performance Meeting (WRFPM 2017) (USB Flash Drive), 10 Pages, 2017/09
We focused on one of accident tolerant fuel (ATF) materials, Oxide Dispersion Strengthened Fe-Cr-Al Steel (FeCrAl-ODS). There is a reasonable prospect that FeCrAl-ODS is applied to BWRs, but relatively high neutron absorption should be compensated. To decrease adverse neutron economic impact, thin FeCrAl-ODS cladding was designed, and we evaluated characteristics of a core into which 9
9 Advanced BWR (ABWR) bundles with thin FeCrAl-ODS claddings were loaded. Thin FeCrAl-ODS water rods and channel boxes were also applied. We confirmed that FeCrAl-ODS core reactivity was sufficient by increasing enrichment of UO fuel under the limit of 5 wt%. Moreover, some representative FeCrAl-ODS core characteristics were comparable to zircaloy core. We also confirmed that fuel thermal-mechanical behaviors of thin FeCrAl-ODS cladding at normal operation and transient conditions were acceptable. These results led to a conclusion that FeCrAl-ODS was applicable to BWR in the analysis range of this study.
Kimura, Akihiko*; Yuzawa, Sho*; Sakamoto, Kan*; Hirai, Mutsumi*; Kusagaya, Kazuyuki*; Yamashita, Shinichiro
Proceedings of 2017 Water Reactor Fuel Performance Meeting (WRFPM 2017) (USB Flash Drive), 10 Pages, 2017/09
The effect of Al addition on the PRW weldability of ODS steel is shown with the discussion focusing on the microstructure changes by the welding. The ordinary welding methods including electron beam (EB) welding and tungsten inert gas (TIG) welding were also applied to the SUS430 endcap welding to cladding tube made of FeCrAl-ODS steel. The endcap welded ODS steel tube samples were tensile tested at RT. The EB welded FeCrAl-ODS/SUS430 samples broke in the ODS steel tube, indicating that the weld bond is stronger than the ODS base metal. However, the TIG welded FeCrAl-ODS/SUS430 samples broke at a weld bond. X-ray CT scan analysis was performed for the weld bond, and the bonding strength was correlated with the X-ray CT results in order to assess the feasibility of those welding methods for ATF-ODS steel cladding.
Sakamoto, Kan*; Hirai, Mutsumi*; Ukai, Shigeharu*; Kimura, Akihiko*; Yamaji, Akifumi*; Kusagaya, Kazuyuki*; Kondo, Takao*; Yamashita, Shinichiro
Proceedings of 2017 Water Reactor Fuel Performance Meeting (WRFPM 2017) (USB Flash Drive), 7 Pages, 2017/09
This paper will show the overview of current status of development of accident tolerant FeCrAl-ODS fuel claddings for BWRs (boiling water reactors) in the program sponsored and organized by the Ministry of Economy, Trade and Industry (METI) of Japan. This program is being carried out to create the technical basis for the practical use of the accident tolerant fuels and the other components in LWRs through multifaceted activities. In the development of FeCrAl-ODS fuel claddings both the experimental and the analytical studies have been performed. The acquisition and accumulation of key material properties of FeCrAl-ODS fuel claddings were conducted by using bar, sheet and tube shaped FeCrAl-ODS materials fabricated in this program to support the evaluations in the analytical studies. A neutron irradiation test was also started in the ORNL High Flux Isotope Reactor (HFIR) to examine the effect of neutron irradiation on the mechanical properties.
Yamaji, Akifumi*; Yamasaki, Daiki*; Okada, Tomoya*; Sakamoto, Kan*; Yamashita, Shinichiro
Proceedings of 2017 Water Reactor Fuel Performance Meeting (WRFPM 2017) (USB Flash Drive), 10 Pages, 2017/09
Features of the accident tolerant fuel performance were evaluated with FEMAXI-7 when the current Zircaloy(Zry) cladding is replaced with FeCrAl-ODS steel cladding (a type of oxide dispersion strengthened steel being developed under the Project on Development of Technical Basis for Safety Improvement at Nuclear Power Plants by Ministry of Economy, Trade and Industry (METI) of Japan) for BWR 99 type fuel rod. In particular, influences of the creep strain rate and thickness of the ODS cladding on the fuel temperature, fission gas release rate (FGR) and pellet-cladding mechanical interaction (PCMI) are investigated.
