Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Kobayashi, Takanori; Sakon, Miyoji; Takada, Osamu; Hatori, Masakazu; Sakamoto, Tsutomu; Sato, Toshiyuki; Kazama, Akihito*; Ishizawa, Yoshihiro*; Igawa, Katsuhisa*; Nakae, Hideo*
JAEA-Review 2011-047, 48 Pages, 2012/02
JAEA-Review-2011-047.pdf:9.58MB
I confirmed a leak of the effluent gas from cylinder part during a load examination after the check of the emergency generator C unit on December 28, 2010 of the facilities check average and confirmed crack in No.8 cylinder liner part. As a result, because it was not performed oil pressure management properly without attaching an oil pressure gauge when I removed cylinder liner about the cause, crack occurred by having been able to write excessive stress for the cylinder liner and reached damage. By a process of this investigation, a fall of the materials strength of some cylinder liner was confirmed, but because a lead ingredient got mixed with materials by a casting process at the time of the production of the cylinder liner, as for this, Widmannst tten graphite occurred, and it became clear that materials strength fell. In addition, I performed inspection by the supersonic wave velocity measurement as technique to distinguish this Widmannst tten graphite easily and confirmed that I was effective.
Ando, Masaki; Iijima, Susumu*; Oigawa, Hiroyuki; Sakurai, Takeshi; Nemoto, Tatsuo*; Okajima, Shigeaki; Osugi, Toshitaka*; Ono, Akio; Hayasaka, Katsuhisa; Sodeyama, Hiroshi
JAEA-Data/Code 2006-006, 67 Pages, 2006/03
JAEA-Data-Code-2006-006.pdf:6.08MB
As a part of research and development of an advanced fueled fast reactor, we carried out benchmark experiments in the FCA-XVII-1 core with MOX simulating fuel to obtain reference data to be compared with those measured in the FCA-XVI-1 and XVI-2 cores simulating metallic fueled FBR. Following nuclear characteristics were measured in the experiments: Criticality, reaction rate ratio, sample reactivity worth, sodium void reactivity effect and 
U Doppler effect. Extra measurements were performed in modified FCA-XVII-1 cores to obtain experimental data for various reactor types: (1) Measurement of sodium void reactivity effect in various plutonium isotope compositions, (2) Measurement of sodium void reactivity effect in a core where axial blanket was replaced with a sodium layer and (3) Measurement of various nuclear characteristics in a nitride fuel region. This report describes methods and results of the above experiments and method of analysis.
*; Tanigawa, Shingo*; *; Yamaguchi, Katsuhisa; *; *; *
PNC TN9410 88-141, 159 Pages, 1988/09
The structural analyses of the core support plate have been applied to study thermal transfomation behaviors and the differences of the movement by changing analytical model, under anticipated transient without scram (ATWS) conditions of FBR. The analyses have been performed for 1000 MWe class loop type fast breeder reactor using a structural analysis code FINAS. The thermal-hydraulic results, which have been performed to ATWS conditions using a plant system code, were used as the thermal boundary conditions to the calculation. The scope of the analyses included a whole section of reactor vessel and the dead load of core assemblies was also considered. Following results were obtained from these studies. (1)The thermal transformation of a upper core support plate can be evaluated according to the free expansion behavior owing to the temperature change of core support plate itself. (2)The radial restriction due to core subassemblies has much influence on the axial bend of the core support plate. (3)There are some differences to the transformation results between by the whole model and by the one dimensional model during the thermal transient is large. Another analysis will be needed, however, about the reactivity change according to the displacement of the core structure.
*; Haraguchi, Tetsuharu*; *; Tanigawa, Shingo*; Yamaguchi, Katsuhisa
PNC TN9410 88-107, 121 Pages, 1988/09
In the studies using PLANDTL, it would be planned to valid the thermal-hydraulic analysis codes which were developed each for whole system, plenum and subassembly, and also to evaluate the reactor plant in the future using these codes. SSC-L is to be as the main code in these studies and is used for design analysis through test analysis. In the first step of this study, model development and modification of SSC-L has been achieved for PLANDTL and predictive analyses have been applied as to validate the models and examine the design of PLANDTL. The estimated transient curves have been obtained about flow rate and temperatures at subassembly and loop of PLANDTL. As a result, the design conditions have been given to be able to perform the programmed tests. It have been validated that the conditions of tests would be within the design value, and the characteristics of PLANDTL and operational conditions have been obtained from the predictive analyses using design data of the plant. The modification and validation of SSC-L will be applied using the results of various kinds of functional tests, and test analyses will be performed in future.