Design loads and structural member modelling to shock-resistant design of buildings

Ikawa, Nozomu*; Mukai, Yoichi*; Nishida, Akemi; Hamamoto, Takuji*; Kano, Toshiya*; Ota, Toshiro*; Nakamura, Naohiro*; Komuro, Masato*; Takeuchi, Masato*

Proceedings of 12th International Conference on Shock and Impact Loads on Structures (SI 2017) (USB Flash Drive), p.259 - 268, 2017/06

Accidental actions on building structures involve impact and explosion loads. The design loads due to impact are determined by experiment data, impact simulation and energetics approach. These loads are presented in the form of load-time (F-t) curves caused by collision and explosion. It is assumed that the structure is rigid and immovable and that impacting body absorbs all the energy (i.e., hard impact condition is supposed), because this assumption gives conservative results in general. Responses of individual structural members directly-subjected to an impulsive load are evaluated. These responses are classified into three types; impulsive response, dynamic response, and quasi-static response. The maximum responses are basically estimated by direct integration method with a single-degree-of-freedom (SDOF) model. The procedure of the SDOF modelling based on the classification of types of members and failure modes is proposed in AIJ guideline.

On-site background measurements for the J-PARC E56 experiment; A Search for the sterile neutrino at J-PARC MLF

Ajimura, Shuhei*; Bezerra, T. J. C.*; Chauveau, E.*; Enomoto, T.*; Furuta, Hisataka*; Harada, Masahide; Hasegawa, Shoichi; Hiraiwa, T.*; Igarashi, Yoichi*; Iwai, Eito*; et al.

Progress of Theoretical and Experimental Physics (Internet), 2015(6), p.063C01_1 - 063C01_19, 2015/06

https://doi.org/10.1093/ptep/ptv078

The J-PARC E56 experiment aims to search for sterile neutrinos at the J-PARC Materials and Life Science Experimental Facility (MLF). In order to examine the feasibility of the experiment, we measured the background rates of different detector candidate sites, which are located at the third floor of the MLF, using a detector consisting of plastic scintillators with a fiducial mass of 500 kg. The gammas and neutrons induced by the beam as well as the backgrounds from the cosmic rays were measured, and the results are described in this article.

Disassembly of JT-60 tokamak device

Okano, Fuminori; Ikeda, Yoshitaka; Sakasai, Akira; Hanada, Masaya; Ichige, Hisashi; Miyo, Yasuhiko; Kaminaga, Atsushi; Sasajima, Tadayuki; Nishiyama, Tomokazu; Yagyu, Junichi; et al.

JAEA-Technology 2013-031, 42 Pages, 2013/11

JAEA-Technology-2013-031.pdf:18.1MB

The disassembly of JT-60 tokamak device and its peripheral equipments, where the total weight was about 6200 tons, started in 2009 and accomplished in October 2012. This disassembly was required process for JT-60SA project, which is the Satellite Tokamak project under Japan-EU international corroboration to modify the JT-60 to the superconducting tokamak. This work was the first experience of disassembling a large radioactive fusion device based on Radiation Hazard Prevention Act in Japan. The cutting was one of the main problems in this disassembly, such as to cut the wielded parts together with toroidal field coils, and to cut the vacuum vessel into two. After solving these problems, the disassembly completed without disaster and accident. This report presents the outline of the JT-60 disassembly, especially tokamak device.

Developing the soil moisture sensor using optical fiber technique (Joint research)

Komatsu, Mitsuru*; Nishigaki, Makoto*; Seno, Shoji*; Hirata, Yoichi*; Takenobu, Kazuyoshi*; Tagishi, Hirotaka*; Kunimaru, Takanori; Maekawa, Keisuke; Yamamoto, Yoichi; Toida, Masaru*; et al.

JAEA-Research 2012-001, 77 Pages, 2012/09

JAEA-Research-2012-001.pdf:4.85MB

This research focused on methods of estimating the amounts of groundwater recharge, which are normally required as upper boundary conditions in groundwater flow analyses, based on measurements of infiltrating water in the ground, to systematize the methods and establish systems which are stable and measurable on site over a long time. Regarding developing measurement systems, fiber-optic strain measurement methods that enable multiple-point and long-distance measurement were used for measuring three quantities: suction pressure, soil moisture and volumetric water content rate obtained by applying water absorption swelling material, and each measurement was discussed. The results showed that the fiber-optic soil aquameter has two types of practical application: one for measuring suction pressure (Type I), and the other for measuring volumetric water content rate obtained by applying water absorption swelling material (Type III). Furthermore, by using measurement instruments in actual fields, the validity of the two methods for estimating the rainfall infiltration capacities of shallow-layer soils, that is, estimating the capacities either directly by measurements of soil water or from unsaturated hydraulic conductivities, was confirmed.

Identified charged hadron production in collisions at = 200 and 62.4 GeV

Adare, A.*; Afanasiev, S.*; Aidala, C.*; Ajitanand, N. N.*; Akiba, Yasuyuki*; Al-Bataineh, H.*; Alexander, J.*; Aoki, Kazuya*; Aphecetche, L.*; Armendariz, R.*; et al.

Physical Review C, 83(6), p.064903_1 - 064903_29, 2011/06

https://doi.org/10.1103/PhysRevC.83.064903

Transverse momentum distributions and yields for , and in collisions at = 200 and 62.4 GeV at midrapidity are measured by the PHENIX experiment at the RHIC. We present the inverse slope parameter, mean transverse momentum, and yield per unit rapidity at each energy, and compare them to other measurements at different collisions. We also present the scaling properties such as and scaling and discuss the mechanism of the particle production in collisions. The measured spectra are compared to next-to-leading order perturbative QCD calculations.

Azimuthal correlations of electrons from heavy-flavor decay with hadrons in and Au+Au collisions at = 200 GeV

Adare, A.*; Afanasiev, S.*; Aidala, C.*; Ajitanand, N. N.*; Akiba, Yasuyuki*; Al-Bataineh, H.*; Alexander, J.*; Aoki, Kazuya*; Aphecetche, L.*; Aramaki, Y.*; et al.

Physical Review C, 83(4), p.044912_1 - 044912_16, 2011/04

https://doi.org/10.1103/PhysRevC.83.044912

Measurements of electrons from the decay of open-heavy-flavor mesons have shown that the yields are suppressed in Au+Au collisions compared to expectations from binary-scaled collisions. Here we extend these studies to two particle correlations where one particle is an electron from the decay of a heavy flavor meson and the other is a charged hadron from either the decay of the heavy meson or from jet fragmentation. These measurements provide more detailed information about the interaction between heavy quarks and the quark-gluon matter. We find the away-side-jet shape and yield to be modified in Au+Au collisions compared to collisions.

Application of cathodic protection of stainless steel for components in fuel reprocessing plant

Ueno, Fumiyoshi; Uchiyama, Yohei*; Kato, Chiaki; Yamamoto, Masahiro; Ebina, Tetsunari*; Shimogawara, Shigeru*; Kano, Yoichi*

Nihon Genshiryoku Gakkai Wabun Rombunshi, 9(3), p.279 - 287, 2010/09

https://doi.org/10.3327/taesj.J09.035

An application of cathodic protection method with impressed current system to control corrosion of austenitic stainless steel in boiling nitric acid solution was studied to improve corrosion resistance of components in fuel reprocessing plant. Plate and tube type specimens made of ultra low carbon type 304 stainless steel (SUS304ULC) were immersed in boiling nitric acid solutions using electrochemical test cells, electrochemical potentiostatic tests and cathodic protection tests were performed. Corrosion rates in the solution with and without protection were measured. As the results, corrosion rates of plate type specimens with cathodic protection were decreased from 1/40 to 1/10 against without protection. In the case of tube type specimen, loss of outer surface thickness was decreased about 1/8, and no deviation of the loss was observed. Authors were concluded that cathodic protection method was expectative as one of the maintenance methods of components in fuel reprocessing plant.

Proliferation and cell death of human glioblastoma cells after carbon-ion beam exposure; Morphologic and morphometric analyses

Oishi, Takuma*; Sasaki, Atsushi*; Hamada, Nobuyuki*; Ishiuchi, Shogo*; Funayama, Tomoo; Sakashita, Tetsuya; Kobayashi, Yasuhiko; Nakano, Takashi*; Nakazato, Yoichi*

Neuropathology, 28(4), p.408 - 416, 2008/08

https://doi.org/10.1111/j.1440-1789.2008.00899.x

Development of timing signal generator for real-time control

Akasaka, Hiromi; Takano, Shoji; Sato, Tomoki; Kawamata, Yoichi

Heisei-18-Nendo Nagoya Daigaku Sogo Gijutsu Kenkyukai Kairo, Keisoku, Seigyo Gijutsu Kenkyukai Hokokushu, p.106 - 109, 2007/03

no abstracts in English

Key R&D activities supporting disposal of radioactive waste; Responding to the challenges of the 21st century

Miyamoto, Yoichi; Umeki, Hiroyuki; Osawa, Hideaki; Naito, Morimasa; Nakano, Katsushi; Makino, Hitoshi; Shimizu, Kazuhiko; Seo, Toshihiro

Nuclear Engineering and Technology, 38(6), p.505 - 534, 2006/08

Ensuring sufficient supplies of clean, economic and acceptable energy is a critical global challenge for the 21st century. There seems little alternative to a greatly expanded role for nuclear power, but implementation of this option will depend on ensuring that all resulting wastes can be disposed of safely. Although there is a consensus on the fundamental feasibility of such disposal by experts in the field, concepts have to be developed to make them more practical to implement and, in particular, more acceptable to key stakeholders. By considering global trends and using illustrative examples from Japan, key areas for future R&D are identified and potential areas where the synergies of international collaboration would be beneficial are highlighted.