Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Sn conductor for ITER central solenoidTakahashi, Yoshikazu; Nabara, Yoshihiro; Ozeki, Hidemasa; Hemmi, Tsutomu; Nunoya, Yoshihiko; Isono, Takaaki; Matsui, Kunihiro; Kawano, Katsumi; Oshikiri, Masayuki; Uno, Yasuhiro; et al.
IEEE Transactions on Applied Superconductivity, 24(3), p.4802404_1 - 4802404_4, 2014/06
Times Cited Count：25 Percentile：72.88(Engineering, Electrical & Electronic)Japan Atomic Energy Agency (JAEA) is procuring all amounts of NbSn conductors for Central Solenoid (CS) in the ITER project. Before start of mass-productions, the conductor should be tested to confirm superconducting performance in the SULTAN facility, Switzerland. The original design of cabling twist pitches is 45-85-145-250-450 mm, called normal twist pitch (NTP). The test results of the conductors with NTP was that current shearing temperature (Tcs) is decreasing due to electro-magnetic (EM) load cycles. On the other hand, the results of the conductors with short twist pitches (STP) of 25-45-80-150-450 mm show that the Tcs is stabilized during EM load cyclic tests. Because the conductors with STP have smaller void fraction, higher compaction ratio during cabling is required and possibility of damage on strands increases. The technology for the cables with STP was developed in Japanese cabling suppliers. The several key technologies will be described in this paper.
Sakuraba, Naotoshi; Numata, Masami; Komiya, Tomokazu; Ichise, Kenichi; Nishi, Masahiro; Tomita, Takeshi; Usami, Koji; Endo, Shinya; Miyata, Seiichi; Kurosawa, Tatsuya; et al.
JAEA-Technology 2009-071, 34 Pages, 2010/03
JAEA-Technology-2009-071.pdf:21.07MB
As a part of maintenance technology of a large-sized glove box for handling of TRU nuclides, we developed replacement technology for front acrylic panels using the bag-in/bag-out method and applied this technology to replace the deteriorated front acrylic panels at Waste Safety Testing Facility (WASTEF) in Nuclear Science Research Institute of Japan Atomic Energy Agency (JAEA). As a consequence, we could safely replace the front acrylic panels under the condition of continuous negative pressure only with partial decontamination of the glove box. We also demonstrated that the present technology is highly effective in points of safety, workability and cost as compared to the usual replacement technology for front acrylic panels of a glove box, where workers in an air-line suit replace directly the front acrylic panels in a green house.
Ando, Masami; Wakai, Eiichi; Tanigawa, Hiroyasu; Kawasaki, Yasushi
Nihon Kinzoku Gakkai-Shi, 72(10), p.785 - 788, 2008/10
Times Cited Count：1 Percentile：12.99(Metallurgy & Metallurgical Engineering)no abstracts in English
Maekawa, Fujio; Sakurai, Kiyoshi; Kosako, Kazuaki*; Kume, Etsuo; Kawasaki, Nobuo*; Nomura, Yasushi; Naito, Yoshitaka*
JAERI-Data/Code 99-048, p.52 - 0, 1999/12
JAERI-Data-Code-99-048.pdf:2.34MB
no abstracts in English
fuel and nucleonics analysis, 2; Measurements of FP nuclidesIto, Mitsuo; Fukaya, Hiroyuki; Ueno, Takashi; Miyata, Seiichi; Sonoda, Takashi; Usami, Hidehiko; Sakazume, Yoshinori; Kurosawa, Tatsuya; Kawasaki, Yasushi; Inagawa, Jun; et al.
no journal, ,
no abstracts in English
Yamane, Yuichi; Amano, Yuki; Yanagida, Yoshinori; Kawasaki, Yasushi; Sato, Makoto; Hayasaka, Hiromi; Tashiro, Shinsuke; Abe, Hitoshi; Uchiyama, Gunzo; Ueda, Yoshinori*; et al.
no journal, ,
The release and transport characteristics of radioactive materials at a boiling accident of the high active liquid waste (HALW) in a reprocessing plant have been studied for improving experimental data of source terms of the boiling accident. This paper describes an experiment using a small test device having an electric furnace, in which 100 mL of the HALW was heated from room temperature to 300
C and the amount of materials released during heating was measured. The amount of materials as a function of its initial concentration in the HALW is reported.
