Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
FCC hierarchical martensite transformation under dynamic impact in FeMnAlNiTi alloyLi, C.*; Fang, W.*; Yu, H. Y.*; Peng, T.*; Yao, Z. T.*; Liu, W. G.*; Zhang, X.*; 徐 平光; Yin, F.*
Materials Science & Engineering A, 892, p.146096_1 - 146096_11, 2024/02
被引用回数：0 パーセンタイル：0.02(Nanoscience & Nanotechnology)The quasi-static superelastic responses and hierarchical martensite transformation from body-centered cubic (BCC) to face-centered cubic (FCC) under dynamic impact in Fe
Mn
Al
Ni
Ti
alloys were investigated. Polycrystalline and oligocrystalline alloys were produced through solution heat treatment and cyclic heat treatment processes, respectively. The results show the volume fraction of residual martensite for oligocrystalline alloys is lower, which exhibits better superelastic responses compared with polycrystalline alloys. Dynamic impact tests indicate that, despite the weakening of the grain boundary strengthening effect, the ultimate strength of the oligocrystalline alloys closely matches that of the polycrystalline alloys under dynamic impact. The martensite transformation of the FeMnAlNiTi alloy is characterized as hierarchical under dynamic impact, and increasing strain rates and grain sizes can enhance the BCC FCC martensite transformation, resulting in higher martensite phase fractions for oligocrystalline alloys. The increase in ultimate strength is attributed to the dynamic Hall-Petch effect introduced by more martensite phase interfaces under dynamic impact.
Xu, X.*; 大平 拓実*; Xu, S.*; 平田 研二*; 大森 俊洋*; 植木 洸輔*; 上田 恭介*; 成島 尚之*; 長迫 実*; 貝沼 亮介*; et al.
Advanced Materials & Processes, 180(7), p.35 - 37, 2022/10
Metallic biomaterials are widely used to replace or support failing hard tissues due to excellent mechanical properties and high wear resistance, with demand increasing as the global population continues to age. It is widely accepted that successful metallic biomaterials should have good biocompatibility, high corrosion resistance, and strong wear resistance. In addition, a low Young's modulus similar to human bone is now recognized as another important factor, in order to avoid bone atrophy due to the stress shielding effect. While the Young's modulus of stainless steels and conventional fcc CoCr alloys is as high as 190-240 GPa, for 
-type Ti-base alloys it is generally in the range of 50-80 GPa. Young's modulus values are as low as 35 GPa for Ti-Nb-Ta-Zr, close to that of human bone at approximately 10-30 GPa. However, Ti-base alloys come with the compromise of low wear resistance. In fact, alloys that feature a low Young's modulus along with high wear resistance have been difficult to realize. This article explores the recently developed bcc CoCr-base alloy Co-Cr-Al-Si as a potential solution to these issues, i.e., the difficulty in combining a low Young's modulus with high wear resistance, and the challenge of realizing large superelastic strains.
大平 拓実*; Xu, S.*; 平田 研二*; Xu, X.*; 大森 俊洋*; 植木 洸輔*; 上田 恭介*; 成島 尚之*; 長迫 実*; Harjo, S.; et al.
Advanced Materials, 34(27), p.2202305_1 - 2202305_11, 2022/07
被引用回数：12 パーセンタイル：87.92(Chemistry, Multidisciplinary)The demand for biomaterials has been increasing along with the increase in the population of elderly people worldwide. The mechanical properties and high wear resistance of metallic biomaterials makes them well-suited for use as substitutes or as support for damaged hard tissues. However, unless these biomaterials also have a low Young's modulus similar to that of human bones, bone atrophy inevitably occurs. Because a low Young's modulus is typically associated with poor wear resistance, it is difficult to realize a low Young's modulus and high wear resistance simultaneously. Also, the superelastic property of shape memory alloys makes them suitable for biomedical applications, like vascular stents and guide wires. However, due to the low recoverable strain of conventional biocompatible shape memory alloys, the demand for a new alloy system is high. The novel body-center-cubic cobalt-chromium-based alloys in this paper provide a solution to both of these problems. We believe our novel alloys are promising candidates for biomedical applications.
田口 浩*; 多田 栄介
JAERI-Tech 99-079, p.28 - 0, 1999/11
ITERの中心部分を構成するブランケット及びダイバータ等の炉内機器は、DT燃焼により放射化及び損傷する。そのため損傷した炉内機器は、放射化物の飛散を防ぐ二重シール扉を備えたキャスクを用いて遠隔操作により保守交換を行う必要がある。その際、二重シール扉には放射化ダスト等の飛散を防止するシール性能、遠隔操作に適した取り扱いの容易性及び耐放射線(
線)性が要求される。本研究では、従来の金属Cリングガスケットの弾性要素であるバネ材にTi-Ni系超弾性合金(Super Elastic Alloy: SEA)を適用して試験を実施した。この結果、標準品金属Cリングガスケットと比較して、少ない締付け力(機器の小型化の可能性)及び繰り返し使用時での気密性能を確保(容易な取り扱いの可能性)できる可能性が確認された。
清水 来紀*; Xu, X.*; 伊東 達矢; Gong, W.; Harjo, S.; 大森 俊洋*; 貝沼 亮介*
no journal, ,
Co-Cr-Al-Si合金は約15%程度の超弾性回復ひずみを有するが、応力誘起マルテンサイト変態開始時の過剰な応力
が超弾性疲労特性を劣化させる可能性がある。本研究では中性子回折によりの起源を調査する。
