Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Nakashio, Nobuyuki*; Osugi, Takeshi; Kurosawa, Shigenobu; Ishikawa, Joji; Hemmi, Ko; Iketani, Shotaro; Yokobori, Tomohiko
JAEA-Technology 2022-016, 47 Pages, 2022/08
JAEA-Technology-2022-016.pdf:2.23MB
The Nuclear Science Research Institute (NSRI) of the Japan Atomic Energy Agency (JAEA) started operation of the Advanced Volume Reduction Facilities (AVWF) for production of waste packages for disposal of low-level radioactive solid wastes (LLW). To clarify the operating conditions for homogenization of non-metallic LLW, preliminary tests were carried out using the plasma melting furnace of the non-metal melting unit. The fluidity of molten waste influences homogenization conditions of solidified products. It was clarified that the viscosity, which is determined by the chemical composition and the melting temperature, influence the fluidity of molten waste greatly through previous literature review and the small-scale melting tests. In the preliminary tests, the simulated waste with a cold tracer loaded in 200 L drums were melted. Using the waste chemical components (basicity, iron oxide concentration) as an experimental parameter, the homogeneity of the chemical components of the solidified product was investigated and the homogenization conditions of melting tests were examined. The retention ratio of the tracer in the molten bath was also confirmed. The viscosity of the molten wastes was measured and the correlation with homogeneity was examined. In addition, the technical requirements that should be concerned in advance for future actual operation were discussed.
Kawaguchi, Munemichi; Miyahara, Shinya; Uno, Masayoshi*
Netsu Sokutei, 45(1), p.2 - 8, 2018/01
Liquid sodium (Na) has been used as the coolant of fast reactors for the various merits, such as the high thermal conductivity. On the other hand, it is postulated that a steel liner may fail and lead to a sodium-concrete reaction (SCR) during the Na-leak accident. Because of concrete ablation and release of hydrogen gas due to the chemical reactions between Na and concrete components, the SCR is one of the important phenomena in the Na-leak accident. In the study, fundamental experiments related to the SCR were performed using Na and concrete powder. Here, the used concrete powder is milled siliceous concrete which is usually used as the structural concrete in Japanese nuclear power plants. The obvious temperature changes at 3 temperature regions were observed for the reaction process such as Na-melt, NaOH-SiO
and Na-HO-SiO reaction, which occurred around 100, 300 and 500
C, respectively. Especially, the violent reaction around 500C caused the temperature peak to 
C, and the reaction heat of 
kW/g was estimated under the Na-concrete mixing ratio such as 
. The main components of the reaction products was identified as NaSiO
with X-ray diffraction technique. Moreover, the measured thermophysical properties such as melting point, density, specific heat, thermal conductivity and viscosity were similar to those of 
NaO-
SiO (
).
Otani, Eiji*; Suzuki, Akio*; Ando, Ryota*; Urakawa, Satoru*; Funakoshi, Kenichi*; Katayama, Yoshinori
Advances in High-Pressure Technology for Geophysical Applications, p.195 - 209, 2005/09
This paper summarizes the techniques for the viscosity and density measurements of silicate melt and glasses at high pressure and temperature by using the X-ray radiography and absorption techniques in the third generation synchrotron radiation facility, SPring-8, Japan. The falling sphere method using in situ X-ray radiography makes it possible to measure the viscosity of silicate melts to the pressures above 6 GPa at high temperature. We summarize the details of the experimental technique of the viscosity measurement, and the results of the measurements of some silicate melts such as the albite and diopside-jadeite systems. X-ray absorption method is applied to measure the density of the silicate glasses such as the basaltic glass and iron sodium disilicate glass up to 5 GPa at high temperature. A diamond capsule, which is not reactive with the glass, is used for the density measurement of the glasses. The present density measurement of the glasses indicates that this method is useful for measurement of the density of silicate melts at high pressure and temperature.
Idesaki, Akira; Narisawa, Masaki*; Okamura, Kiyohito*; Sugimoto, Masaki; Tanaka, Shigeru; Morita, Yosuke; Seguchi, Tadao; Ito, Masayoshi*
Journal of Materials Science, 36(23), p.5565 - 5569, 2001/12
Times Cited Count：40 Percentile：77.80(Materials Science, Multidisciplinary)A very fine silicon carbide (SiC) fiber with diameter of 6 
m, about a half of that of a commercially available SiC fiber, was synthesized from a polymer blend of polycarbosilane (PCS) and polyvinylsilane (PVS). The fine SiC fiber was obtained by optimizing the composition and the spinning temperature of PCS-PVS polymer blends. In order to determine these optimum conditions, the relationship between temperature and melt viscosities of the polymer blends was investigated. As a result, it was found that the optimum spinning temperature range was within a temperature range where the melt viscosity is 5-10Pa
s. Moreover, by blending PVS with PCS, the spinning temperature of the polymer blends was lowered, the spinnability of polymer system was improved, and finer polymer fiber was obtained compared with PCS. The optimum content of PVS in the polymer blend was 15-20wt%.
Terasaki, Hidenori*; Kato, Takumi*; Urakawa, Satoru*; Funakoshi, Kenichi*; Suzuki, Akio*; Okada, Taku; Maeda, Makoto*; Sato, Jin*; Kubo, Tomoaki*; Kasai, Shizu*
Earth and Planetary Science Letters, 190(1-2), p.93 - 101, 2001/07
Times Cited Count：55 Percentile：68.78(Geochemistry & Geophysics)The Fe-FeS melt is thought to be the major candidate of the outer core material. Its viscosity is one of the most important physical properties to study the dynamics of the convection in the outer core. We performed the in situ viscosity measurement of the Fe-FeS melt under high pressure using X-ray radiography falling sphere method with a novel sample assembly. Viscosity was measures in the temperature, pressure, and compositional conditions of 1233-1923 K, 1.5-6.9 GPa, and Fe-Fe 
S 
(wt %), respectively. The viscosity coefficients obtained by 17 measurements change systematically in the range of 0.008-0.036 Pa s. An activation energy of the viscous flow, 30 kJ/mol, and the activation volume, 1.5 cm 
/mol, are determined as the temperature and pressure dependence, and the viscosity of the Fe S melt is found to be smaller than that of the Fe melt by 15 %. These tendencies can be well correlated with the structural variation of the Fe-FeS melt.
