FBR metallic materials test manual (2023 revised edition)

Imagawa, Yuya; Toyota, Kodai; Onizawa, Takashi; Kato, Shoichi

JAEA-Testing 2023-004, 76 Pages, 2024/03

JAEA-Testing-2023-004.pdf:2.08MB

This manual describes the methods for conducting material tests in air, argon gas, and sodium, and for organizing the data obtained, as a part of the development of high-temperature structural design technology for fast reactors. This manual reflects the revision of test methods in Japanese Industrial Standards (JIS) to the "FBR Metallic Materials Test Manual, PNC TN241 77-03" published in 1977 and the "FBR Metallic Materials Test Manual (Revised Edition), JNC TN9520 2001-001" published in 2001. Also, it was written with reference to the recommended room temperature / elevated temperature tensile test method by the Japan Society of Mechanical Engineers (JSME) and the test standard for the elevated-temperature low-cycle fatigue test method by the Society of Materials Science, Japan (JSMS), which are the standard for material test methods in the domestic academic society.

Validation of the applicability of the best-fit fatigue curves for 550C in Mod.9Cr-1Mo steel to 110 cycles

Toyota, Kodai; Imagawa, Yuya; Onizawa, Takashi; Kato, Shoichi; Furuya, Yoshiyuki*

Nihon Kikai Gakkai Rombunshu (Internet), 89(928), p.23-00206_1 - 23-00206_15, 2023/12

https://doi.org/10.1299/transjsme.23-00206

In order to design fast reactors, it is necessary to consider high cycle fatigue of structural materials up to 110 cycles; to evaluate high cycle fatigue at 110 cycles, it is necessary to develop a best-fit fatigue curve applicable up to 110 cycles. In this study, high cycle fatigue tests were conducted under strain-controlled conditions and ultrasonic fatigue tests were also conducted to develop a high cycle fatigue evaluation method for Mod.9Cr-1Mo steel, which is a candidate material for fast reactor structural materials. Based on the test results, the best-fit fatigue curves were extended and the applicability of the JSME best-fit fatigue curves up to 110 cycles was verified.

Equipment renewal, facility improvement, and dismantling / removal in the glove-box at basic laboratory of Plutonium Conversion Development Facility

Umino, Yoshinori; Kato, Keisuke; Tanigawa, Masafumi; Kobayashi, Daisuke; Obu, Tomoyuki; Kimura, Yuichi*; Nemoto, Ryo*; Tajiri, Kazuma*

Nihon Hozen Gakkai Dai-19-Kai Gakujutsu Koenkai Yoshishu, p.33 - 36, 2023/08

In the basic laboratory of the Plutonium Conversion Development Facility in Tokai Reprocessing Plant, tests had been conducted to obtain effective data for manufacturing mixed plutonium and uranium oxide powder by irradiating a mixture of plutonium and uranium solution with microwaves. The test has already been completed, and we are currently dismantling and removing equipment. In this paper, techniques related to equipment renewal, dismantling and removal works inside the glove-box are discussed.

Chemical species of cesium and iodine in condensed vaporized microparticles formed by melting nuclear fuel components with concrete materials

Onuki, Toshihiko*; Ye, J.*; Kato, Tomoaki; Liu, J.; Takano, Masahide; Kozai, Naofumi; Utsunomiya, Satoshi*

Environmental Science; Processes & Impacts, 25(7), p.1204 - 1212, 2023/07

https://doi.org/10.1039/D3EM00074E

To elucidate chemical forms of Cs and I in microparticles produced via the Fukushima Daiichi Nuclear Power Plant accident and released into the atmosphere, we analyzed Cs and I in condensed vaporized particles (CVP) produced by melting experiments using nuclear fuel components containing CsI with concrete. CVPs consisted of many round particles containing Cs and I of diameters less than several tens of micrometers. Two kinds of particles were present: one containing large amounts of Cs and I, suggesting the presence of CsI, and the other containing small amounts of Cs and I with large Si contents. Most of CsI from both particles were dissolved in water. On the contrary, some fractions of Cs remained from the latter particles. These results suggest that Cs was incorporated in CVPs along with Si to form water low-soluble CVPs

Pressure-modulated magnetism and negative thermal expansion in the HoFe intermetallic compound

Cao, Y.*; Zhou, H.*; Khmelevskyi, S.*; Lin, K.*; Avdeev, M.*; Wang, C.-W.*; Wang, B.*; Hu, F.*; Kato, Kenichi*; Hattori, Takanori; et al.

Chemistry of Materials, 35(8), p.3249 - 3255, 2023/04

https://doi.org/10.1021/acs.chemmater.3c00158

Hydrostatic and chemical pressure are efficient stimuli to alter the crystal structure and are commonly used for tuning electronic and magnetic properties in materials science. However, chemical pressure is difficult to quantify and a clear correspondence between these two types of pressure is still lacking. Here, we study intermetallic candidates for a permanent magnet with a negative thermal expansion (NTE). Based on in situ synchrotron X-ray diffraction, negative chemical pressure is revealed in HoFe on Al doping and quantitatively evaluated by using temperature and pressure dependence of unit cell volume. A combination of magnetization and neutron diffraction measurements also allowed one to compare the effect of chemical pressure on magnetic ordering with that of hydrostatic pressure. Intriguingly, pressure can be used to control suppression and enhancement of NTE. Electronic structure calculations indicate that pressure affected the top of the majority band with respect to the Fermi level, which has implications for the magnetic stability, which in turn plays a critical role in modulating magnetism and NTE. This work presents a good example of understanding the effect of pressure and utilizing it to control properties of functional materials.

Decommissioning of uranium handling facility for development of nuclear fuel manufacturing equipment

Kageyama, Tomio; Denuma, Akio; Koizumi, Jin*; Odakura, Manabu*; Haginoya, Masahiro*; Isaka, Shinichi*; Kadowaki, Hiroyuki*; Kobayashi, Shingo*; Morimoto, Taisei*; Kato, Yoshiaki*; et al.

JAEA-Technology 2022-033, 130 Pages, 2023/03

JAEA-Technology-2022-033.pdf:9.87MB

Uranium handling facility for development of nuclear fuel manufacturing equipment (Mockup room) was constructed in 1972. The Mockup room has a weak seismic resistance and is deteriorating with age. Also, the original purpose with this facility have been achieved and there are no new development plans using this facility. Therefore, interior equipment installed in this facility had been dismantled and removed since March 2019. After that, the Mockup room was inspected for contamination, and then controlled area in the Mockup room was cancelled on March 29th 2022. A total of 6,549 workers (not including security witnesses) were required for this work. The amount of non-radioactive waste generated by this work was 31,300 kg. The amount of radioactive waste generated by this work was 3,734 kg of combustible waste (103 drums), 4,393 kg of flame resistance waste (61 drums), 37,790 kg of non-combustible waste (124 drums, 19 containers). This report describes about the dismantling and removing the interior equipment in the Mockup room, the amount of waste generated by this work, and procedure for cancellation the controlled area in the facility.

Composite with a glassy nonporous coordination polymer enhances gas adsorption selectivity

Zheng, X.*; Kato, Masaru*; Uemura, Yohei*; Matsumura, Daiju; Yagi, Ichizo*; Takahashi, Kiyonori*; Noro, Shinichiro*; Nakamura, Takayoshi*

Inorganic Chemistry, 62(3), p.1257 - 1263, 2023/01

https://doi.org/10.1021/acs.inorgchem.2c04068

Design and actual performance of J-PARC 3 GeV rapid cycling synchrotron for high-intensity operation

Yamamoto, Kazami; Kinsho, Michikazu; Hayashi, Naoki; Saha, P. K.; Tamura, Fumihiko; Yamamoto, Masanobu; Tani, Norio; Takayanagi, Tomohiro; Kamiya, Junichiro; Shobuda, Yoshihiro; et al.

Journal of Nuclear Science and Technology, 59(9), p.1174 - 1205, 2022/09

https://doi.org/10.1080/00223131.2022.2038301

In the Japan Proton Accelerator Research Complex, the purpose of the 3 GeV rapid cycling synchrotron (RCS) is to accelerate a 1 MW, high-intensity proton beam. To achieve beam operation at a repetition rate of 25 Hz at high intensities, the RCS was elaborately designed. After starting the RCS operation, we carefully verified the validity of its design and made certain improvements to establish a reliable operation at higher power as possible. Consequently, we demonstrated beam operation at a high power, namely, 1 MW. We then summarized the design, actual performance, and improvements of the RCS to achieve a 1 MW beam.

Sodium-cooled Fast Reactors

Ohshima, Hiroyuki; Morishita, Masaki*; Aizawa, Kosuke; Ando, Masanori; Ashida, Takashi; Chikazawa, Yoshitaka; Doda, Norihiro; Enuma, Yasuhiro; Ezure, Toshiki; Fukano, Yoshitaka; et al.

Sodium-cooled Fast Reactors; JSME Series in Thermal and Nuclear Power Generation, Vol.3, 631 Pages, 2022/07

https://shop.elsevier.com/books/sodium-cooled-fast-reactors/morishita/978-0-12-824076-2

This book is a collection of the past experience of design, construction, and operation of two reactors, the latest knowledge and technology for SFR designs, and the future prospects of SFR development in Japan. It is intended to provide the perspective and the relevant knowledge to enable readers to become more familiar with SFR technology.

Measurements of thermal conductivity for near stoichiometric (UPuAm)O (z = 0.05, 0.10, and 0.15)

Yokoyama, Keisuke; Watanabe, Masashi; Tokoro, Daishiro*; Sugimoto, Masatoshi*; Morimoto, Kyoichi; Kato, Masato; Hino, Tetsushi*

Nuclear Materials and Energy (Internet), 31, p.101156_1 - 101156_7, 2022/06

https://doi.org/10.1016/j.nme.2022.101156

In current nuclear fuel cycle systems, to reduce the amount of high-level radioactive waste, minor actinides (MAs) bearing MOX fuel is one option for burning MAs using fast reactor. However, the effects of Am content in fuel on thermal conductivity are unclear because there are no experimental data on thermal conductivity of high Am bearing MOX fuel. In this study, The thermal conductivities of near stoichiometric (UPuAm)O solid solutions(z = 0.05, 0.10, and 0.15) have been measured between room temperature (RT) and 1473 K. The thermal conductivities decreased with increasing Am content and satisfied the classical phonon transport model ((A+BT)) up to about 1473 K. A values increased linearly with increasing Am content because the change in ionic radius affects the conduction of the phonon due to the solid solution in U and Am. B values were independent of Am content.