Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Moriyama, Junichiro*; Takakuwa, Osamu*; Yamaguchi, Masatake; Ogawa, Yuhei*; Tsuzaki, Kaneaki*
Computational Materials Science, 232, p.112650_1 - 112650_11, 2024/01
Times Cited Count：0 Percentile：0(Materials Science, Multidisciplinary)The present study focuses on a novel hydrogen-improved strength-ductility balance in some practical Fe-Cr-Ni-based austenitic alloys, which directly depends on the solute hydrogen content. The hydrogen absorption energy of the Fe-Cr-Ni model alloys with the face-centered cubic structure was examined using first-principles calculations to verify the contribution of Cr and Ni substitutions from Fe to the hydrogen solubility in the alloys. The Cr substitution substantially reduced the hydrogen absorption energy compared to the Ni substitution, whereby the increased Cr/Ni ratio exerts higher hydrogen solubility. The propensity in the calculations coincided with the experimental results obtained previously in the practical alloys with various Cr / Ni ratios.
Kamiya, Junichiro; Takano, Kazuhiro*; Wada, Kaoru; Yanagibashi, Toru*
e-Journal of Surface Science and Nanotechnology (Internet), 21(3), p.144 - 153, 2023/06
no abstracts in English
Np and 
Am gamma ray regionsFukuda, Tatsuo; Kobata, Masaaki; Shobu, Takahisa; Yoshii, Kenji; Kamiya, Junichiro; Iwamoto, Yosuke; Makino, Takahiro*; Yamazaki, Yuichi*; Oshima, Takeshi*; Shirai, Yasuhiro*; et al.
Journal of Applied Physics, 132(24), p.245102_1 - 245102_8, 2022/12
Times Cited Count：1 Percentile：15.88(Physics, Applied)Direct energy conversion has been investigated using Ni/SiC Schottky junctions with the irradiation of monochromatized synchrotron X-rays simulating the gamma rays of Np (30 keV) and Am (60 keV). From current-voltage measurements, electrical energies were obtained for both kinds of gamma rays. The energy conversion efficiencies were found to reach up to 
1.6%, which is comparable to those of a few other semiconducting systems reported thus far. This result shows a possibility of energy recovery from nuclear wastes using the present system, judging from the radiation tolerant nature of SiC. Also, we found different conversion efficiencies between the two samples. This could be understandable from hard X-ray photoelectron spectroscopy and secondary ion mass spectroscopy measurements, suggesting the formation of Ni-Si compounds at the interface in the sample with a poor performance. Hence, such combined measurements are useful to provide information that cannot be obtained by electrical measurements alone.
Yamamoto, Kazami; Kinsho, Michikazu; Hayashi, Naoki; Saha, P. K.; Tamura, Fumihiko; Yamamoto, Masanobu; Tani, Norio; Takayanagi, Tomohiro; Kamiya, Junichiro; Shobuda, Yoshihiro; et al.
Journal of Nuclear Science and Technology, 59(9), p.1174 - 1205, 2022/09
Times Cited Count：5 Percentile：87.42(Nuclear Science & Technology)In the Japan Proton Accelerator Research Complex, the purpose of the 3 GeV rapid cycling synchrotron (RCS) is to accelerate a 1 MW, high-intensity proton beam. To achieve beam operation at a repetition rate of 25 Hz at high intensities, the RCS was elaborately designed. After starting the RCS operation, we carefully verified the validity of its design and made certain improvements to establish a reliable operation at higher power as possible. Consequently, we demonstrated beam operation at a high power, namely, 1 MW. We then summarized the design, actual performance, and improvements of the RCS to achieve a 1 MW beam.
Kamiya, Junichiro; Takano, Kazuhiro*; Yuza, Hiromu*; Wada, Kaoru
e-Journal of Surface Science and Nanotechnology (Internet), 20(2), p.107 - 118, 2022/05
no abstracts in English
Nakanoya, Takamitsu; Kamiya, Junichiro; Yoshimoto, Masahiro; Takayanagi, Tomohiro; Tani, Norio; Kotoku, Hirofumi*; Horino, Koki*; Yanagibashi, Toru*; Takeda, Osamu*; Yamamoto, Kazami
JAEA-Technology 2021-019, 105 Pages, 2021/11
JAEA-Technology-2021-019.pdf:10.25MB
Since a user operation startup, the 3 GeV synchrotron accelerator (Rapid-Cycling Synchrotron: RCS) gradually reinforced the beam power. As a result, the surface dose rate of the apparatus located at the beam injection area of the RCS, such as the magnet, vacuum chambers, beam monitors, etc., increases year by year. The beam injection area has many apparatuses which required manual maintenance, so reducing worker's dose is a serious issue. To solve this problem, we have organized a task force for the installation of the shield. The task force has aimed to optimize the structure of the radiation shield, construct the installation procedure with due consideration of the worker's dose suppression. As the examination result of the shield design, we have decided to adopt removal shielding that could be installed quickly and easily when needed. We carried out shield installation work during the 2020 summer maintenance period. The renewal work required to install the shielding has been carried out in a under high-dose environment. For this reason, reducing the dose of workers was an important issue. So, we carefully prepared the work plan and work procedure in advance. During the work period, we implemented various dose reduction measures and managed individual dose carefully. As a result, the dose of all workers could be kept below the predetermined management value. We had installed removal shielding at the beam injection area in the 2020 summer maintenance period. We confirmed that this shield can contribute to the reduction of the dose during work near the beam injection area. It was a large-scale work to occupy the beam injection area during almost of the summer maintenance period. However, it is considered very meaningful for dose suppression in future maintenance works.
Takano, Kazuhiro; Kotoku, Hirofumi*; Kobayashi, Fuminori*; Miyao, Tomoaki*; Moriya, Katsuhiro; Kamiya, Junichiro
JAEA-Technology 2021-017, 35 Pages, 2021/11
JAEA-Technology-2021-017.pdf:5.32MB
In J-PARC LINAC, the vacuum system of L3BT, which is a beam transport line connecting LINAC and 3GeV synchrotron, uses a turbo molecular pump and roots pump for rough exhaust and an ion pump for main exhaust. In addition, beam dumps are connected to the end of the L3BT at 0 degree, 30 degree, 90 degree, and 100 degree positions via vacuum partition windows. The roots pumps are used as the exhaust system for each beam dump. The roots pump controllers have been installed away from the pump in the accelerator tunnel to avoid radiation damages. Besides, the special controllers, which have no inverter circuit inside, have been used to reduce the electrical noise on the beam loss monitors nearby. However, using the special controller without inverters, several problems have occurred such as the instability or wide variability of the pumping speed. To solve such problems, the roots pump controller with the inverter circuit must be used after reducing the electrical noise. In this report, some countermeasures to reduce the electrical noise from the inverters were investigated. The noise reduction circuit was successfully optimized to the level where the beam loss monitors works unaffected.
Nakanoya, Takamitsu; Kamiya, Junichiro; Yoshimoto, Masahiro; Takayanagi, Tomohiro; Tani, Norio; Kotoku, Hirofumi*; Horino, Koki*; Yanagibashi, Toru*; Takeda, Osamu*; Yamamoto, Kazami
Proceedings of 18th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.238 - 242, 2021/10
Since a user operation startup, the 3GeV synchrotron accelerator (Rapid-Cycling Synchrotron: RCS) gradually reinforced the beam power. As a result, the surface dose rate of the apparatus located at the beam injection area of the RCS increases year by year. The beam injection area has many apparatuses which required manual maintenance, so reducing worker's dose is a serious issue. To solve this problem, we have decided to adopt removal shielding that could be installed quickly and easily when needed. We carried out shield installation work during the 2020 summer maintenance period. The installation work of the shield has been carried out in a under high-dose environment. For this reason, reducing the dose of workers was an important issue. So, we carefully prepared the work plan and work procedure in advance. During the work period, we implemented various dose reduction measures and managed individual dose carefully. As a result, the dose of all workers could be kept below the predetermined management value. We had installed removal shielding at the beam injection area in the 2020 summer maintenance period. We confirmed that this shield can contribute to the reduction of the dose during work near the beam injection area.
Kamiya, Junichiro; Kotoku, Hirofumi*; Kurosawa, Shunta*; Takano, Kazuhiro; Yanagibashi, Toru*; Yamamoto, Kazami; Wada, Kaoru
Physical Review Accelerators and Beams (Internet), 24(8), p.083201_1 - 083201_23, 2021/08
Times Cited Count：0 Percentile：0.02(Physics, Nuclear)Through the operation of the vacuum system in J-PARC, it becomes evident that the high-power beam has more powerful effects on the vacuum system than expected. Those effects are the malfunction of vacuum equipment and the large pressure rise. The former is the failure of the turbomolecular pump (TMP) controller. The TMP itself is also damaged by a bearing crush due to a touch-down. We have developed a TMP controller that can connect with long cables of more than 200 m lengths to install the controller in a control room where there is no radiation influence. The TMP with high-strength bearing has been also developed. The latter is an extreme pressure rise with increasing the beam power. It is indicated that the pressure rise mechanism is a result of ion-stimulated gas desorption. It is finally confirmed that the dynamic pressure during the high-power beam is effectually suppressed by additionally installing the NEG pumps.
Kamiya, Junichiro; Takano, Kazuhiro; Yuza, Hiromu*; Wada, Kaoru
Proceedings of 12th International Particle Accelerator Conference (IPAC 21) (Internet), p.3471 - 3474, 2021/08
The NEG coating, which has been developed in CERN, is a revolutionary technique that can make a beam pipe act as a vacuum pump by coating the getter materials with the ability to adsorb/absorb gas molecules on the beam pipe surface. The NEG materials are alloys of titanium, zirconium, and vanadium. Titanium is one of the getter materials. In high-power beam accelerators, titanium has been used as the beam pipe chamber material due to its low radioactivation characteristics. The ordinal titanium surface has no getter function because it is covered with titanium-oxide film. The new technique, which removes the titanium-oxide surface by the sputtering and makes the titanium vacuum chamber itself the vacuum pump like NEG coated chamber, has been developed. After sputtering the inner surface of the titanium chamber, we obtained clear evidence that shows the chamber acts as a vacuum pump. We have also tried to make a titanium chamber with a getter function only by baking. Dependence of the getter characteristics on the baking temperature will also be reported.
Shobuda, Yoshihiro; Kamiya, Junichiro; Takayanagi, Tomohiro; Horino, Koki*; Ueno, Tomoaki*; Yanagibashi, Toru*; Kotoku, Hirofumi*
Proceedings of 12th International Particle Accelerator Conference (IPAC 21) (Internet), p.3205 - 3208, 2021/08
At the injection area of the RCS in J-PARC, the interaction between the copper stripes (RF-shields) on the ceramic chambers and the external magnetic fields modulatesthe magnetic fields in the chamber, causing beam losses for a special tune. A ceramic chamber spirally covered by the stripes is a candidate to mitigate the modulations. In this report, we numerically and experimentally investigate how the interaction is suppressed, while sustaining the beam impedance enhancement within tolerable at the RCS.
Kamiya, Junichiro; Kotoku, Hirofumi; Hikichi, Yusuke*; Takahashi, Hiroki; Yamamoto, Kazami; Kinsho, Michikazu; Wada, Kaoru*
JPS Conference Proceedings (Internet), 33, p.011023_1 - 011023_6, 2021/03
The vacuum system is the key for the stable high power beam operation in J-PARC 3 GeV rapid cycling synchrotron (RCS), because the gas molecules in the beam line make the beam loss due to the scattering. The more than 10 years operation of the RCS vacuum system showed that the ultra-high vacuum (UHV) has been stably maintained by the several developments. The challenges for lower beam line pressure will exist in a future operation with higher beam power. For such challenge, a TMP with a rotor of titanium alloy, which have much higher mechanical strength than aluminum allow for the normal rotter, has been developed. Overcoming the difficulties of the machining performance of the titanium alloy rotor was successfully manufactured. We will report the summary of the 10 years operation of the RCS vacuum system and the incoming developments towards the XHV.
Kamiya, Junichiro; Kotoku, Hirofumi; Shobuda, Yoshihiro; Takayanagi, Tomohiro; Yamamoto, Kazami; Yanagibashi, Toru*; Horino, Koki*; Miki, Nobuharu*
Journal of Physics; Conference Series, 1350, p.012172_1 - 012172_7, 2019/12
Times Cited Count：0 Percentile：0.06(Physics, Particles & Fields)One of the issues in the J-PARC 3 GeV rapid cycling synchrotron is the high residual radiation dose around the beam injection point. A radiation shield is necessary to reduce radiation exposure of workers when maintenance is performed there. A space to install the radiation shield should be secured by newly designing a structure of the vacuum chamber at the injection point and the alumina ceramics beam pipes for the shift bump magnets. To make the space for the shield, the chamber is lengthened along the beam line and the cross-sectional shape is changed from circle to rectangle. The displacement and inner stress of the vacuum chamber due to atmospheric pressure were evaluated to be enough small by the calculation. For the ceramics beam pipe's rf-shield, the damping resistor was effective to reduce the induced modulation voltages by the pulsed magnetic field.
Yamamoto, Kazami; Yamakawa, Emi*; Takayanagi, Tomohiro; Miki, Nobuharu*; Kamiya, Junichiro; Saha, P. K.; Yoshimoto, Masahiro; Yanagibashi, Toru*; Horino, Koki*; Nakanoya, Takamitsu; et al.
ANS RPSD 2018; 20th Topical Meeting of the Radiation Protection and Shielding Division of ANS (CD-ROM), 9 Pages, 2018/08
The existing beam power of the J-PARC Rapid Cycling Synchrotron is up to 500 kW, and higher radiation doses are concentrated in the injection area. These activations are caused by the interaction between the foil and the beam. To reduce dose exposure to workers near the injection point, we study a new design of the injection scheme. Experience has shown that eddy currents are generated in the metal flange near the magnet owing to the pulsed magnetic field, and the temperature exceeds 100 degrees C. The shield installed in the new injection system needs to have a layer structure, in which an insulator is inserted between iron shields to reduce the eddy current. From the results of the shielding calculation, even if 1 mm of polyethylene was inserted between two 9-mm-thick SUS 316 plates, which serve as shielding material, the shielding performance was reduced only about 5%, and we confirmed that it would function well.
Takayanagi, Tomohiro; Yamamoto, Kazami; Kamiya, Junichiro; Saha, P. K.; Ueno, Tomoaki*; Horino, Koki*; Kinsho, Michikazu; Irie, Yoshiro*
IEEE Transactions on Applied Superconductivity, 28(3), p.4100505_1 - 4100505_5, 2018/04
Times Cited Count：4 Percentile：25.6(Engineering, Electrical & Electronic)Yamamoto, Kazami; Kamiya, Junichiro; Saha, P. K.; Takayanagi, Tomohiro; Yoshimoto, Masahiro; Hotchi, Hideaki; Harada, Hiroyuki; Takeda, Osamu*; Miki, Nobuharu*
Proceedings of 14th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.374 - 378, 2017/12
The 3-GeV Rapid Cycling Synchrotron (RCS) of Japan Proton Accelerator Research Complex (J-PARC) aims to deliver 1-MW proton beam to the neutron target and Main Ring synchrotron. Present beam power of the Rapid Cycling Synchrotron is up to 500-kW and the higher radiation doses were concentrated in the injection area. These activations were caused by the interaction between the foil and the beam. To reduce the worker dose near the injection point, we have studied a new design of the injection scheme to secure enough space for radiation shielding and bellows. In the new system, two of four injection pulse bump magnets are replaced and we are able to ensure the additional space around the injection foil chamber. So far, new injection system seems not impossible. However, preliminary study result indicated that temperature of the duct and shielding metals would be slightly higher. The eddy current due to the shift bump magnet field generates heat. Thus we have to study details of above effect.
Okabe, Kota; Yamamoto, Kazami; Kamiya, Junichiro; Takayanagi, Tomohiro; Yamamoto, Masanobu; Yoshimoto, Masahiro; Takeda, Osamu*; Horino, Koki*; Ueno, Tomoaki*; Yanagibashi, Toru*; et al.
Proceedings of 14th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.853 - 857, 2017/12
The most important issue is to reduce the uncontrolled beam loss in the high intensity hadron accelerator such as J-PARC proton accelerators. The J-PARC 3 GeV Synchrotron (RCS) has a collimator system which narrows a high intensity beam in the RCS. After startup of RCS in 2007, the collimator system of the RCS worked well. However, in April 2016, vacuum leakage at the collimator system occurred during the maintenance operation. To investigate a cause of the failure, we took apart iron shields of the collimator reducing exposed dose of operators. As a result of inspection, we succeeded to identify the cause of the vacuum leakage failure. In this presentation, we report the failure investigation of the beam collimator system in the RCS.
Yamamoto, Kazami; Kamiya, Junichiro; Saha, P. K.; Takayanagi, Tomohiro; Yoshimoto, Masahiro; Hotchi, Hideaki; Harada, Hiroyuki; Takeda, Osamu*; Miki, Nobuharu*
Proceedings of 8th International Particle Accelerator Conference (IPAC '17) (Internet), p.579 - 581, 2017/05
The 3-GeV Rapid Cycling Synchrotron of Japan Proton Accelerator Research Complex aims to deliver 1-MW proton beam to the neutron target and Main Ring synchrotron. Present beam power of the Rapid Cycling Synchrotron is up to 500-kW and the higher radiation doses were concentrated in the injection area. These activations were caused by the interaction between the foil and the beam. To reduce the worker dose near the injection point, we have studied a new design of the injection scheme to secure enough space for radiation shielding and bellows. In the new system, two of four injection pulse bump magnets are replaced and we are able to ensure the additional space around the injection foil chamber. So far, new injection system seems not impossible. However, preliminary study result indicated that temperature of the duct and shielding metals would be slightly higher. The eddy current due to the shift bump magnet field generates heat. Thus we have to study details of above effect.
Yamamoto, Kazami; Okabe, Kota; Kamiya, Junichiro; Yoshimoto, Masahiro; Takeda, Osamu; Takayanagi, Tomohiro; Yamamoto, Masanobu
Proceedings of 13th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.314 - 318, 2016/11
The 3 GeV Rapid-Cycling Synchrotron (RCS) of the Japan Proton Accelerator Research Complex (J-PARC) project generates 1MW proton beam for the neutron experiments and Main ring accelerator. In case of such high intensity hadron accelerator, the most important issue is to reduce the uncontrolled loss. The beam collimation system is designed for this purpose. In the present design, the physical aperture is 1.5 times wider than the primary collimator aperture and the beam loss can be enough localized on this condition. After a startup of RCS in 2007, the collimator system of RCS worked well. But vacuum leakage occurred during the maintenance period in April, 2016. Since it was expected that the beam collimator was radio-activated very much, we took the influence of radiation into consideration and designed the collimator (ie. a remote clamp system to connect/take off it with a vacuum flange away from itself). Therefore, during the recovery work of the collimator, we were able to reduce the worker dose to less than 60 micro Sv though the collimator block had a residual dose of 40 mSv/h.
Kamiya, Junichiro; Hikichi, Yusuke; Kinsho, Michikazu; Ogiwara, Norio; Fukuda, Mitsuhiro*; Hamatani, Noriaki*; Hatanaka, Kichiji*; Kamakura, Keita*; Takahisa, Keiji*
Journal of Vacuum Science and Technology A, 33(3), p.031605_1 - 031605_8, 2015/05
Times Cited Count：5 Percentile：22.77(Materials Science, Coatings & Films)For the vacuum systems of high-intensity beam accelerators, low radioactivation materials with good vacuum characteristics and high mechanical strength are required. The titanium alloy Ti-6Al-4V was investigated as a potential low activation vacuum material with high mechanical strength for the fabrication of vacuum components, particularly the flanges of beam pipes, in the J-PARC 3 GeV synchrotron. The dose rate of Ti-6Al-4V when irradiated by a 400 MeV proton was observed to decrease more rapidly than that of stainless steel. Furthermore, the generated radioactive isotopes were nuclides with relatively short half-lives. The outgassing rate of Ti-6Al-4V was the same as the typical value for stainless steel. Additionally, the hydrogen concentration in bulk Ti-6Al-4V was reduced to approximately 1 ppm by vacuum firing. These results indicate that Ti-6Al-4V is a good candidate for use as a low activation vacuum material with high mechanical strength.
